《08-30176974-DC.pdf》由会员分享，可在线阅读，更多相关《08-30176974-DC.pdf（11页珍藏版）》请在三一文库上搜索。
1、a Date: 23 January 2008 Origin: International Latest date for receipt of comments: 30 April 2008 Project no.: 2007/00280 Responsible committee: GEL/15/3/5 Flexible insulating sleeving for electrical purposes Interested committees: Title: Draft IEC 62329-3-101 ED 1 Heat shrinkable moulded shapes Part
2、 3 Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 101 Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance Supersession information: If this document is published as a s
3、tandard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRA
4、FT IS NOT CURRENT BEYOND 30 April 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without pri
5、or written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies
6、 of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be ob
7、tained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 020 8996 7205 Responsible Com
8、mittee Secretary: Mr A Ashrafi (BSI) E-mail: asghar.ashrafibsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 08/30176974 DC Licensed Copy: London South Bank University, London South Bank Unive
9、rsity, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent standard. If no commen
10、ts are received to the contrary, then the UK will approve this draft. There is a high probability that this text could be adopted by CENELEC as a reference document for harmonization or as a European Standard. Recipients of this draft are requested to comment on the text bearing in mind this possibi
11、lity. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts
12、 are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comm
13、ents in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a
14、 comment form are available from the BSI web site at: http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (
15、justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as a
16、n alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank Uni
17、versity, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/405/CD COMMITTEE DRAFT (CD) IEC/TC or SC: TC15 Project number IEC 62329-3-101 Ed. 1.0 Title of TC/SC: Solid Electrical Insulating Materials Date of circulation 2008-01-18 Closing date for comments 2008-04-18 Also of interest
18、to the following committees TC112 Supersedes document 15/364/CD and 15/385/CC Functions concerned: Safety EMC Environment Quality assurance Secretary: John A. Gauthier, USA Email: THIS DOCUMENT IS STILL UNDER STUDY AND SUBJECT TO CHANGE. IT SHOULD NOT BE USED FOR REFERENCE PURPOSES. RECIPIENTS OF T
19、HIS DOCUMENT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. Title: IEC 62329-3-101 Ed. 1.0: Heat shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, material requ
20、irements and compatibility performance - Sheet 101: Heat- shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. (Titre) : Introductory note This project began as IC 62329-3-100 Ed. 1.0: Heat shrinkable moulded shapes Part 3: Specificati
21、on for individual materials Sheet 100 to 107: Requirements for shape dimensions, material requirements and compatibility performance. It was decided at the last TC 15 plenary meeting in Prague (May 2007) to separate this project into the 3 following parts: IEC 62329-3-100 Ed. 1.0: Heat shrinkable mo
22、ulded shapes - Part 3: Specification requirements for shape dimensions, material requirements and compatibility performance - Sheet 100: Heat-shrinkable moulded shape dimensions IEC 62329-3-101 Ed. 1.0: Heat shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, materia
23、l requirements and compatibility performance - Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. IEC 62329-3-102 Ed. 1.0: Heat shrinkable moulded shapes - Part 3: Specification requirements for shape dimensions, mate
24、rial requirements and compatibility performance - Sheet 102: Heat-shrinkable elastomeric moulded shapes, semi-rigid, material requirements and system performance FORM CD (IEC) 2002-08-08 Copyright 2008 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download t
25、his electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions. You may not copy or “mirror“ the file or printed version of the document, or any part of it, for any other purpose without permission in writing from IEC. Licensed Copy: L
26、ondon South Bank University, London South Bank University, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/405/CD 2 INTERNATIONAL ELECTROTECHNICAL COMMISSION HEAT SHRINKABLE MOULDED SHAPES Part 3: Specification requirements for shape dimensions, material requirements and compatibil
27、ity performance Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. FOREWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnic
28、al committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation i
29、s entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with
30、the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant su
31、bjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendations for international use and are published in the form of standards, technical reports or guides and they are accepted by the National Committees
32、in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or reg
33、ional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements o
34、f this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62329-3-101 has been prepared by subcommittee 15C: Specifications, of IEC technical committee 15: Insulating materials. T
35、he text of this standard is based on the following documents: FDIS Report on voting Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 1
36、5 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/405/CD 3 INTRODUCTION This International Standard is one of a series that deals with heat shrinkable moulded shapes for electrical purposes. The series consists of three parts: Part 1: Definitions and general requirements (IEC 62329-1) Part 2:
37、 Methods of test (IEC 62329-2) Part 3: Specification requirements for moulded shape dimensions, material requirements and compatibility performance. (IEC 62329-3) This Standard gives one of the sheets comprising part 3 as follows. Sheet 101: Heat shrinkable moulded shapes, polyolefin, semi-rigid, li
38、mited fire hazard, material requirements and system performance. Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/405/CD 4 HEAT SHRINKABLE MOULDED SHAPES Part 3: Specification for shape dimensions, material r
39、equirements and compatibility performance Sheet 101: Heat-shrinkable moulded shapes, polyolefin, semi-rigid, limited fire hazard, material requirements and system performance. 1. Scope This sheet of IEC 62329-3 gives the requirements for heat-shrinkable moulded shapes, polyolefin, semi-rigid, limite
40、d fire hazard, material requirements and system performance. Experience of product performance indicates that this moulded shape material is suitable for inclusion in systems for operation in the following temperature range, -30C to + 105C The moulded shapes may be supplied with a pre-coated adhesiv
41、e. Refer to the manufacturers/suppliers for options. A guide to adhesive compatibility is given in Appendix A. These moulded shapes are normally supplied in the styles and dimensions given in IEC 62329-3-100. The colour is normally Black. Styles and dimensions other than those specifically listed in
42、 IEC 62329-3-100 may be available as custom items. These items shall be considered to comply with this standard if they comply with the property requirements listed in Table 1 with the exception of dimensions. Materials that conform to this specification meet established levels of performance. Howev
43、er, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. 2. Normative references The following referenced documents are indispensable for the appli
44、cation of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies IEC 62329-1: Specification for heat shrinkable moulded shapes - Part 1: Definitions and general requirements. IEC 62
45、329-2: Heat shrinkable moulded shapes - Part 2: Methods of test. IEC 62329-3-100 Heat shrinkable moulded shapes dimensions IEC 60757:1983 Code for designation of colours. ISO 846:1997 Plastics - Evaluation of the action of micro-organisms. ISO 1817: 1999 Rubber, vulcanized - Determination of the eff
46、ect of liquids Licensed Copy: London South Bank University, London South Bank University, Fri Feb 15 06:48:22 GMT+00:00 2008, Uncontrolled Copy, (c) BSI 15/405/CD 5 3. Designation The moulded shapes shall be designated as shown by the following example Description IEC publication number IEC Part num
47、ber IEC Sheet number IEC Style/size code Colour Adhesive Code* (1) Drain holes (2) Moulded shapes IEC 62329 3 101 B/01 BK W1 D * For compatible adhesives and codes see Appendix A (1) Insert UN if uncoated (2) Insert N if no drain holes Any abbreviation for colour shall comply with IEC 60757. Where n
48、o abbreviation is given, the colour shall be written in full. 4. Conditions of test for the moulded shapes. The moulded shapes shall be shrunk in a forced air circulation oven for ( 10 1 ) min at the temperature specified in Table 1. 5. Requirements In addition to the general requirements given in I
49、EC 62329-1, the heat-shrinkable moulded shapes shall comply with the dimensional requirements given in IEC 62329-3-100 and Table 1. 6. Moulded shapes material conformance. Conformance with the requirements of this specification shall be based on the results form test sheets, ( 2 0,15 ) thick, unless otherwise specified*, which shall be prepared from the same cross-linked heat shrinkable material that is used to manu