《08-30176807-DC.pdf》由会员分享，可在线阅读，更多相关《08-30176807-DC.pdf（9页珍藏版）》请在三一文库上搜索。
1、a Date: 2 December 2008 Origin: European Latest date for receipt of comments: 31 March 2009 Project no.: 2008/00282 Responsible committee: B/513 Construction equipment and plant and site safety Interested committees: Title: Draft BS EN 12111:2002/A1 Tunnelling machines - Road headers, continuous min
2、ers and impact rippers - Safety requirements Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN12111 : 2002 and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secre
3、tary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 March 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledge
4、ment will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electr
5、onic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Ser
6、vices. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the B
7、ritish Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7224 Responsible Committee Secretary: Mr M J Hodson (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC:
8、 08/30176807 DC Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in th
9、e preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged to publish the officia
10、l English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments re
11、ceive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatib
12、le with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below.
13、Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex
14、 (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains con
15、nector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Micro
16、soft Corporation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 12111:2002 prA1 November 2008 ICS 91.220; 93.060 English Version Tunnelling machines - Road headers, con
17、tinuous miners and impact rippers - Safety requirements Machines pour la construction de tunnels - Machines attaque ponctuelle, mineurs continus et brise-roches hydrauliques - Rgles de scurit Tunnelbaumaschinen - Teilschnittmaschinen, Continuous miners und Schlagkopfmaschinen - Sicherheitstechnische
18、 Anforderungen This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 151. This draft amendment A1, if approved, will modify the European Standard EN 12111:2002. If this draft becomes an amendment, CEN members are boun
19、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amendment was established by CEN in three official versions (English, French, German). A version in any other la
20、nguage made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Fin
21、land, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Warning : This document is not a European Standard. It is distributed for review a
22、nd comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in a
23、ny form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12111:2002/prA1:2008: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI EN 12111:2002/prA1:2008 (E) 2 Contents Page Foreword3 1 Modification to Clause 2
24、.4 2 Modification to 5.1.1 4 3 Modification to 5.6.4.1 .4 4 Addition of 5.6.6.4 5 Modification to 7.1 .4 6 Modification to 7.2.2 5 7 Modification to 7.3.1 5 8 Modification to Annex ZA .6 9 Addition of Annex ZB7 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Unc
25、ontrolled Copy, (c) BSI EN 12111:2002/prA1:2008 (E) 3 Foreword This document (EN 12111:2002/prA1:2008) has been prepared by Technical Committee CEN/TC 151 “Construction equipment and building material machines - Safety”, the secretariat of which is held by DIN. This document is currently submitted t
26、o the Unique Acceptance Procedure. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EC Directive(s). For relationship with EC Directive(s), see informative Annex ZA, B, C or D, whic
27、h is an integral part of this document. The main changes compared to the previous version are: Addition of Annex ZB; Editorial modification of Annex ZA; “Minor” changes of sub-clauses 5.6.6, 7.1, 7.2.2 and 7.3.1; reference to EN 292-1 be replaced by EN ISO 12100-1:2003 and EN 292-2 be replace by EN
28、ISO 12100-2: 2003. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI EN 12111:2002/prA1:2008 (E) 4 1 Modification to Clause 2 Replace “EN 292-1:1991“ with “EN ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for de
29、sign Part 1: Basic terminology, methodology (ISO 12100-1:2003)“. Replace “EN 292-2:1991“ with “EN ISO 12100-2:2003 Safety of machinery Basic concepts, general principles for design Part 2: Technical principles (ISO 12100-2:2003)“. 2 Modification to 5.1.1 In the 2nd paragraph, replace reference to “E
30、N 292“ with “ EN ISO 12100“. 3 Modification to 5.6.4.1 Replace the first sentence with the following: “The A-weighted emission sound pressure level at the control station shall be measured according to EN ISO 11202.“ Add the following sentence: “The sound pressure level shall not exceed 80 dB(A) at
31、the operators position.“ 4 Addition of 5.6.6 Add the following new paragraph:“ 5.6.6 Declaration of noise emission values The declaration of the noise emission values is the sole responsibility of the manufacturer and shall be made in accordance with EN ISO 4871. The noise declaration shall mention
32、explicitly that the noise emission value has been obtained according to this noise test code.“ 5 Modification to 7.1 In the 1st paragraph replace “5.5.1 of EN 292-2:1991/A1:1995“ with “6.5 of EN ISO 12100-2:2003.“ Replace the 3rd paragraph with the following text: “The instruction shall include the
33、following information: the value of the A- weighted sound pressure level determined according to 5.6.4.1 if exceeding 80 dB(A); The vibration total value to which the hand-arm system is subjected, if it exceeds 2,5 m/s. Where this value does not exceed 2,5 m/s, this must be mentioned. the highest ro
34、ot mean square value of weighted acceleration to which the whole body is subjected, if exceeds 0,5 m/s. Where this value does not exceed 0.5 m/s, this shall be mentioned. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI EN 12111:2002/pr
35、A1:2008 (E) 5 the uncertainty of measurement. NOTE 1 The total value of hand-arm vibration of tunnelling machines as defined in this standard is below 2,5 m/s. NOTE 2 This single whole-body vibration emission value determined under particular operating and terrain conditions and is therefore not rep
36、resentative for the various conditions in accordance with the intended use of the machine. Consequently this single whole-body vibration emission value declared by the manufacturer in accordance with this European Standard is not intended to determine the whole-body vibration exposure to the operato
37、r using this machine. NOTE 3 The highest root mean square value of weighted acceleration of whole-body vibration is in accordance with the directive 2002/44/EC the highest value of the 3 values in orthogonal directions of vibration under consideration that the horizontal directions are multiplied by
38、 1,4. NOTE 4 Alternative for the measurement of these vibration values through the manufacturer these values can be determined on the basis of measurement taken for technically comparable machinery which is representative of the machinery to be produced. NOTE 5 Information on the uncertainty of vibr
39、ation measurements and the declaration and verification of vibration values is given in EN 12096:1997. For the estimation of the uncertainty are indicated in Table D.1 values of 0,4 and 0,5 of the measured vibration value in dependency on the vibration level.“ 6 Modification to 7.2.2 Delete “noise“
40、at the end of the 2nd indent. 7 Modification to 7.3.1 Replace the 1st indent with the following: “ business name and full address of the manufacturer or his authorised representative;“ Add the following indent:“ designation of machinery;“. Licensed Copy: London South Bank University, South Bank Univ
41、ersity, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI EN 12111:2002/prA1:2008 (E) 6 8 Modification to Annex ZA Replace the existing Annex ZA with the following: “ Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 98/37/EC This European S
42、tandard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 98/37/EC amended by Directive 98/79/EC on machinery. Once this standard is cited in the O
43、fficial Journal of the European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevan
44、t Essential Requirements except those of chapter 1.1.7, 1.5.7, 1.5.10, 1.5.13 of Annex I of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ Licensed Copy: London South B
45、ank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI EN 12111:2002/prA1:2008 (E) 7 9 Addition of Annex ZB Add the following Annex ZB: “ Annex ZB (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC This Eur
46、opean Standard has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association to provide a means of conforming to Essential Requirements of the New Approach Directive 2006/42/EC on machinery. Once this standard is cited in the Official Journal of th
47、e European Communities under that Directive and has been implemented as a national standard in at least one Member State, compliance with the normative clauses of this standard confers, within the limits of the scope of this standard, a presumption of conformity with the relevant Essential Requireme
48、nts except those of chapter 1.1.7, 1.5.7, 1.5.10, 1.5.13 of Annex I of that Directive and associated EFTA regulations. WARNING Other requirements and other EU Directives may be applicable to the product(s) falling within the scope of this standard.“ Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:42, Uncontrolled Copy, (c) BSI