《08-30178378-DC.pdf》由会员分享，可在线阅读，更多相关《08-30178378-DC.pdf（18页珍藏版）》请在三一文库上搜索。
1、a Date: 26 November 2008 Origin: European Latest date for receipt of comments: 28 February 2009 Project no.: 2008/00643 Responsible committee: MTE/23 Woodworking machines Interested committees: Title: Draft BS EN 1218-3:2001/A1 Safety of woodworking machines - Tenoning machines Part 3: Hand fed teno
2、ning machines with sliding table for cutting structural timbers Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN1218-3 : 2001 and partially supersede. NONE If you are aware of a current national standard which may be affected, ple
3、ase notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 28 February 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publ
4、ication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for br
5、iefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also availabl
6、e from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft
7、 may be found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20
8、8996 7001 Form 36 Version 8.0 DPC: 08/30178378 DC Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft
9、 are welcome and will assist in the preparation of the consequent British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will
10、 be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is inten
11、ded to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front
12、cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be present
13、ed as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) M
14、B Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Ame
15、nd to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, a
16、nd Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM FINAL DRAFT EN 1218-3:2001 prA1 November 2008 ICS 79.120.10 English Version Safety of
17、 woodworking machines - Tenoning machines - Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers Scurit des machines bois - Tenonneuses - Partie 3: Machines avance manuelle et table roulante pour la coupe des lments de charpente de toit en bois Sicherheit von Holzbear
18、beitungsmaschinen - Zapfenschneid- und Schlitzmaschinen - Teil 3: Abbundmaschinen mit von Hand bewegtem Schiebetisch This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee CEN/TC 142. This draft amendment A1, if approved, wil
19、l modify the European Standard EN 1218-3:2001. If this draft becomes an amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment into the relevant national standard without any alteration. This draft amendment
20、 was established by CEN in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the
21、 national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland
22、 and United Kingdom. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a European Standard. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR
23、 NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1218-3:2001/prA1:2008: E Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Unco
24、ntrolled Copy, (c) BSI EN 1218-3:2001/prA1:2008 (E) 2 Contents Page Foreword3 1 Modification to the Foreword .4 2 Modification to Clause 1, Scope.4 3 Modification to Clause 2, Normative references 4 4 Modification to 3.2, Definitions5 5 Modification to Clause 4, List of hazards.6 6 Modification to C
25、lause 5, Safety requirements and/or protective measures (hanging paragraph)8 7 Modification to 5.1.1, Safety and reliability of control systems8 8 Modification to 5.1.3, Starting.8 9 Modification to 5.1.4, Normal stopping .8 10 Modification to 5.1.5, Emergency stop8 11 Modification to 5.1.6, Failure
26、 of the power supply.8 12 Modification to 5.2.1 Stability.8 13 Modification to 5.2.2 Risk of break-up during operation.9 14 Modification to 5.2.3.2, Strength 9 15 Modification to 5.2.3.5, Spindle rings 9 16 Modification to 5.2.5, Devices to minimise the possibility or the effect of ejection.9 17 Mod
27、ification to 5.3.1, Fire and explosion 9 18 Modification to 5.3.4, Electricity.9 19 Modification to 5.3.5, Ergonomics and handling9 20 Modification to 5.3.7, Pneumatics10 21 Modification to 5.3.8, Hydraulics10 22 Modification to 5.3.12, Radiation10 23 Modification to 5.3.13, Laser.11 24 Modification
28、 to 5.3.16, Isolation .11 25 Modification to 5.3.17, Maintenance 11 26 Modification to Clause 6, Information for use (hanging paragraph)11 27 Modification to 6.2, Marking .11 28 Modification to 6.3, Instruction handbook 12 29 Modification to Annex A14 30 Modification to Annex E14 31 Modification to
29、Annex ZA .14 32 Addition of Annex ZB15 33 Modification to Bibliography16 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EN 1218-3:2001/prA1:2008 (E) 3 Foreword This document (EN 1218-3:2001/prA1:2008) has been prepared by Technical Co
30、mmittee CEN/TC 142 “Woodworking machines - Safety”, the secretariat of which is held by UNI. This document is currently submitted to the Unique Acceptance Procedure. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and s
31、upports essential requirements of the Machinery Directive. For relationship with EU Directive, see informative Annexes ZA and ZB, which are integral parts of this document. This document includes Amendment A.1, approved by CEN on XXXX-XX-XX. The main changes compared to the previous version are: - A
32、ddition of Annex ZB - Editorial modification of Annex ZA - “Minor” changes of sub-clauses 1, 2, 3.2, 4, 5, 5.1.1, 5.1.3, 5.1.4, 5.1.5, 5.1.6, 5.2.1, 5.2.2, 5.2.3.2, 5.2.3.5, 5.2.5, 5.3.1, 5.3.4, 5.3.7, 5.3.8, 5.3.16, 5.3.17, 6, 6.2, 6.3, Annex A, Annex E, Bibliography - Technical changes of sub-clau
33、ses 5.3.5, 5.3.12, 5.3.13 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EN 1218-3:2001/prA1:2008 (E) 4 1 Modification to the Foreword Replace the fourth paragraph with the following: “For relationship with EU Directive(s), see inform
34、ative Annexes ZA and ZB, which are integral parts of this document.“ 2 Modification to Clause 1, Scope Replace the first paragraph with: “This document deals with the significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to hand fed tenoning machines with slid
35、ing table for cutting structural timbers, hereinafter referred to as “machines“. Delete the third paragraph. 3 Modification to Clause 2, Normative references Replace the standard paragraph with the following: “The following referenced documents are indispensable for the application of this document.
36、 For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.“. Delete reference EN 292-1:1991 in Clause 2 and replace “EN 292-1:1991“ with “EN ISO 12100-1:2003“ throughout the document. Delete referen
37、ces EN 292-2:1991 and EN 292/A1:1995. Replace reference to EN 418:1992 with: “EN ISO 13850:2008, Safety of machinery - Emergency stop - Principles for design (ISO 13850:2006)“ and replace “EN 418:1992“ in 5.1.5, 1st paragraph, with “EN ISO 13850:2008“. Replace “EN 847-1:1997, Tools for woodworking -
38、 Safety requirements Part 1: Milling tools and circular sawblades“ with “EN 847-1:2005, Tools for woodworking - Safety requirements - Part 1: Milling tools, circular saw blades“ and “EN 847-1:1997“ with “EN 847-1:2005“ throughout the document. Replace “EN 954:1996“ with “EN ISO 13849-1:2008 Safety o
39、f machinery Safety-related parts of control systems Part 1: General principles for design (ISO 13849-1:2006)“ throughout the document. Replace “EN 60204-1:1992“ with “EN 60204-1:2006“ and replace in the title “(IEC 60204-1:1992, modified)“ with “(IEC 60204-1:2005, modified)“ Replace “EN 60947-4-1:19
40、92“ with “EN 60947-4-1:2001“ throughout the document and replace in the title “(IEC 60947-4-1:1990)“ with “(IEC 60947-4-1:2000)“. Replace “EN 60947-5-1:1997“ with “EN 60947-5-1:2004“ throughout the document and replace in the title “(IEC 60947-5-1:1997)“ with “(IEC 60947-5-1:2003)“. Replace referenc
41、e to “ISO 3745:1977“ with “EN ISO 3745:2003, Acoustics Determination of sound power levels of noise sources using sound pressure Precision methods for anechoic and semi-anechoic rooms (ISO 3745:2003)“ and replace “ISO 3745:1977“ with “EN ISO 3745:2003“ throughout the document. Replace reference to “
42、HD 21.1 S3:1997“ with “HD 21.1 S4:2002, Cables of rated voltages up to and including 450/750 V and having thermoplastic insulation Part 1: General requirements“ and replace “HD 21.1 S3:1997“ with “HD 21.1 S4:2002“ throughout the document. Licensed Copy: London South Bank University, South Bank Unive
43、rsity, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI EN 1218-3:2001/prA1:2008 (E) 5 Replace reference to “HD 22.1 S3:1997“ with “HD 22.1 S4:2002, Cables of rated voltages up to and including 450/750 V and having cross-linked insulation Part 1: General requirements“ and replace “HD 22.1 S3:1997“ with
44、“HD 22.1 S4:2002“ throughout the document. Replace reference to “HD 22.4 S3:1995+A1:1999“ with “HD 22.4 S4:2004, Cables of rated voltages up to and including 450/750 V and having crosslinked insulation Part 4: Cords and flexible cables“ and replace “HD 22.4 S3:1995+A1:1999“ with “HD 22.4 S4:2004“ th
45、roughout the document. Add the following references: “EN 614-1:2006, Safety of machinery Ergonomic design principles Part 1: Terminology and general principles“, “EN 894-1:1997, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General principles fo
46、r human interactions with displays and control actuators EN 894-2:1997, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays EN 894-3:2000, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Co
47、ntrol actuators“, “EN 1005-1:2001, Safety of machinery Human physical performance Part 1: Terms and definitions EN 1005-2:2003, Safety of machinery Human physical performance Part 2: Manual handling of machinery and component parts of machinery EN 1005-3:2002, Safety of machinery Human physical perf
48、ormance Part 3: Recommended force limits for machinery operation EN 1005-4:2005, Safety of machinery Human physical performance Part 4: Evaluation of working postures and movements in relation to machinery EN 1037:1995, Safety of machinery Prevention of unexpected start-up“, “EN 50370-1:2005, Electr
49、omagnetic compatibility (EMC) Product family standard for machine-tools Part 1: Emission EN 50370-2:2003, Electromagnetic compatibility (EMC) Product family standard for machine-tools Part 2: Immunity“, “EN 60439-1:1999, Low-voltage switchgear and controlgear assemblies Part 1: Type-tested and partially type-tested assemblies (IEC 60439-1:1999)“, “EN 61310-1: