《08-30176537-DC.pdf》由会员分享，可在线阅读，更多相关《08-30176537-DC.pdf（14页珍藏版）》请在三一文库上搜索。
1、a Date: 29 July 2008 Origin: European Latest date for receipt of comments: 31 October 2008 Project no.: 2008/00224 Responsible committee: TCI/77 Ropes and cordage and fishing nets Interested committees: Title: Draft BS EN ISO 10556: Fibre ropes of polyester/polyolefin dual fibres Supersession inform
2、ation: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGAR
3、DED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 October 2008. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No
4、 copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an orga
5、nization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also available from BSI Customer Services. Information on the co-operating organizations represented on the co
6、mmittees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/. Direct tel: 02
7、0 8996 7009 Responsible Committee Secretary: Committee Service Centre (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 8.0 DPC: 08/30176537 DC Licensed CopyChinese University of Hong Kong, 2
8、1/10/2008 08:04, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent British Standard. If no comments are received to the
9、contrary, then the UK will approve this draft and implement it as a British Standard. Comment is particularly welcome on national, legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK wi
10、ll be obliged to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is int
11、ended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the fron
12、t cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be prese
13、nted as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7)
14、 MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. A
15、mend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks,
16、 and Windows is a trademark of Microsoft Corporation. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI THIS DOCUMENT IS A DRAFT CIRCULATED FOR COMMENT AND APPROVAL. IT IS THEREFORE SUBJECT TO CHANGE AND MAY NOT BE REFERRED TO AS AN INTERNATIONAL STANDARD UNT
17、IL PUBLISHED AS SUCH. IN ADDITION TO THEIR EVALUATION AS BEING ACCEPTABLE FOR INDUSTRIAL, TECHNOLOGICAL, COMMERCIAL AND USER PURPOSES, DRAFT INTERNATIONAL STANDARDS MAY ON OCCASION HAVE TO BE CONSIDERED IN THE LIGHT OF THEIR POTENTIAL TO BECOME STANDARDS TO WHICH REFERENCE MAY BE MADE IN NATIONAL RE
18、GULATIONS. RECIPIENTS OF THIS DRAFT ARE INVITED TO SUBMIT, WITH THEIR COMMENTS, NOTIFICATION OF ANY RELEVANT PATENT RIGHTS OF WHICH THEY ARE AWARE AND TO PROVIDE SUPPORTING DOCUMENTATION. DRAFT INTERNATIONAL STANDARD ISO/DIS 10556 International Organization for Standardization, 2008 INTERNATIONAL OR
19、GANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION ISO/TC 38 Voting begins on: 2008-07-24 Secretariat: SAC Voting terminates on: 2008-12-24 Fibre ropes of polyester/polyolefin dual fibres Cordages en fibres bi-matriaux polyester/polyolfines ICS 59.080.50 ISO/CEN PARALLEL ENQ
20、UIRY The CEN Secretary-General has advised the ISO Secretary-General that this ISO/DIS covers a subject of interest to European standardization. In accordance with the ISO-lead mode of collaboration as defined in the Vienna Agreement, consultation on this ISO/DIS has the same effect for CEN members
21、as would a CEN enquiry on a draft European Standard. Should this draft be accepted, a final draft, established on the basis of comments received, will be submitted to a parallel two-month FDIS vote in ISO and formal vote in CEN. In accordance with the provisions of Council Resolution 15/1993 this do
22、cument is circulated in the English language only. Conformment aux dispositions de la Rsolution du Conseil 15/1993, ce document est distribu en version anglaise seulement. To expedite distribution, this document is circulated as received from the committee secretariat. ISO Central Secretariat work o
23、f editing and text composition will be undertaken at publication stage. Pour acclrer la distribution, le prsent document est distribu tel quil est parvenu du secrtariat du comit. Le travail de rdaction et de composition de texte sera effectu au Secrtariat central de lISO au stade de publication. Lic
24、ensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10556 ii ISO 2008 All rights reserved PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited un
25、less the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a tradema
26、rk of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies.
27、In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. Copyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country,
28、neither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to eit
29、her ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Viol
30、ators may be prosecuted. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10556 ISO 2008 All rights reserved iii Contents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions.1 4 Designation1 5 Materials.2 6 General requirements
31、.2 7 Physical properties .4 8 Marking.8 Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10556 iv ISO 2008 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (I
32、SO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, gov
33、ernmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC
34、 Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the membe
35、r bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 10556 was prepared by Technical Committee ISO/TC 38, Textiles. Licensed
36、CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI DRAFT INTERNATIONAL STANDARD ISO/DIS 10556 ISO 2008 All rights reserved 1 1 Scope This document specifies requirements for 3-strand hawser-laid, 8 strand and 12 strand braided ropes made of polyester in combination wit
37、h polyolefin and it gives rules for their designation. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (includ
38、ing any amendments) applies. ISO 1968, Fibre ropes and cordage Vocabulary ISO 2307, Fibre ropes Determination of certain physical and mechanical properties ISO 9554, Fibre ropes General specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1
39、968 apply. 4 Designation Fibre ropes shall be designated by the words “fibre rope“; number of this document; construction or type of rope (see clause 6); reference number of the rope; materials from which the rope is made; level of performance of rope : fibre rope or higher strength (hs) fibre rope.
40、 EXAMPLE: Designation of a 3-strand hawser-laid rope (reference number 20 (type A) corresponding to a linear density of 194 ktex made of polyester/polyolefin dual fibre: Fibre rope ISO 10556 - A - 20 - polyester/polyolefin Fibre ropes of polyester/polyolefin dual fibres Licensed CopyChinese Universi
41、ty of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10556 2 ISO 2008 All rights reserved EXAMPLE: Designation of a 12-strand braided rope (reference number 20 (type T) corresponding to a linear density of 221 ktex made of higher strength polyester/polyolefin dual fibre: Fibre rope
42、ISO 10556 - T - 20 - polyester/polyolefin (hs) 5 Materials 5.1 Fibres 5.1.1 Polyester: the polyester portion of the rope shall be continuous multifilament, heat and light resistant fibre of industrial (high tenacity) grade. 5.1.2 Polyolefin: the polyolefin portion of the rope shall be of suitable te
43、nacity to meet all the requirements of this specification. NOTE Polyolefin may be polypropylene or a mix of polypropylene and polyethylene with a minimum of 15 % and a maximum of 50 % of polyethylene. 5.2 Yarns 5.2.1 The cover yarns of each strand of fibre ropes shall be made with polyester fibres c
44、overing a polyolefin core and shall contain a minimum of 40 % by weight of polyester fibre (see Tables 1 and 2). NOTE When inside yarns are used, they may consist of 100 % polyolefin fibres. 5.2.2 All the yarns used in higher strength fibre ropes shall be made with polyester fibres of dual fibre. 6
45、General requirements 6.1 Polyester/polyolefin dual fibre ropes shall be made in one of the following constructions: type A: 3-strand hawser-laid rope (see Figure 1); type L: 8-strand braided rope (see Figure 2) ; type T: 12-strand braided rope (see Figure 3). Licensed CopyChinese University of Hong
46、Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10556 ISO 2008 All rights reserved 3 Figure 1 Shape of a 3-strand hawser-laid rope (type A) Figure 2 Shape of an 8-strand braided rope (type L) 1 One plait pitch Figure 3 Shape of a 12-strand braided rope (type T) 6.2 Construction, manufactu
47、re, lay, labelling, packaging, invoicing and delivery lengths shall conform to ISO 9554. Licensed CopyChinese University of Hong Kong, 21/10/2008 08:04, Uncontrolled Copy, (c) BSI ISO/DIS 10556 4 ISO 2008 All rights reserved 7 Physical properties Linear density and minimum breaking force shall confo
48、rm to Tables 1, 2, 3 and 4. Table 1 Fibre ropes : 3-strand hawser-laid rope (type A) of polyester/polyolefin dual fibres Linear density b) c)Minimum breaking force d) e) kN Reference number a) Nominal ktex Tolerance Unspliced ropes Ropes with eye-spliced terminations 6 17,5 10 % 6,8 6,1 8 31,0 11,9
49、10,7 9 39,3 14,9 13,4 10 48,5 18,2 16,4 12 69,9 8 % 25,7 23,1 14 95,1 34,7 31,2 16 124 44,8 40,3 18 157 56,1 50,5 20 194 68,7 61,8 22 235 82,1 73,9 24 279 96,3 86,7 26 328 113 102 28 380 130 117 30 437 148 133 32 497 167 150 36 629 210 189 40 776 5 % 257 231 44 939 308 277 48 1 110 364 328 52 1 320 424 382 56 1 520 489 440 60