《08-30190915-DC.pdf》由会员分享，可在线阅读，更多相关《08-30190915-DC.pdf（5页珍藏版）》请在三一文库上搜索。
1、a Date: 8 October 2008 Origin: European Latest date for receipt of comments: 31 January 2009 Project no.: 2008/03243 Responsible committee: CPL/61/6 Portable motor-operated tools Interested committees: Title: Draft BS EN 60745-2-4/PRAC Hand-held motor operated electric tools - Safety - Part 2-4: Par
2、ticular requirements for sanders and polishers other than disk type Supersession information: If this document is published as a standard, the UK implementation of it will supersede BSEN60745-2-4 : 2003 and partially supersede. NONE If you are aware of a current national standard which may be affect
3、ed, please notify the secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 31 January 2009. This draft is issued to allow comments from interested parties; all comments will be given consideration prior t
4、o publication. No acknowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization
5、for briefing purposes. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email . British, International and foreign standards are also av
6、ailable from BSI Customer Services. Information on the co-operating organizations represented on the committees referenced above may be obtained from the responsible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this
7、 draft may be found via the British Standards Online Service on the BSI web site http:/. Direct tel: 020 8996 7273 Responsible Committee Secretary: Mrs G D Salt (BSI) E-mail: Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7
8、001 Form 36 Version 8.0 DPC: 08/30190915 DC Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:18, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on European discussions in which the UK took an active part. Your comments on this draft are welcom
9、e and will assist in the preparation of the consequent British Standard. Comment is particularly welcome on national legislative or similar deviations that may be necessary. Even if this draft standard is not approved by the UK, if it receives the necessary support in Europe, the UK will be obliged
10、to publish the official English Language text unchanged as a British Standard and to withdraw any conflicting standard. UK Vote Please indicate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensur
11、e that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and will be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comme
12、nts should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given
13、in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are available from the BSI web site at: http:/ Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No.
14、/ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change) by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read .
15、 so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be supported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows i
16、s a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:18, Uncontrolled Copy, (c) BSI Draft for vote FINAL DRAFT EUROPEAN STANDARD EN 60745-2-4 NORME EUROPENNE FprAC EUROPISCHE NORM September 2008 CENELEC European Committee for Elect
17、rotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Proje
18、ct: 22003 Ref. No. EN 60745-2-4:2003/FprAC:2008 E ICS 25.140.20; 25.140.30; 25.080.50 English version Hand-held motor-operated electric tools - Safety - Part 2-4: Particular requirements for sanders and polishers other than disk type Outils lectroportatifs moteur - Scurit - Partie 2-4: Rgles particu
19、lires pour les ponceuses et lustreuses, autres que du type disque Handgefhrte motorbetriebene Elektrowerkzeuge - Sicherheit - Teil 2-4: Besondere Anforderungen fr Schleifer und Polierer auer Tellerschleifern This draft amendment FprAC, if approved, will modify the European Standard EN 60745-2-4:2003
20、; it is submitted to CENELEC members for formal vote. Deadline for CENELEC: 2008-11-28. It has been drawn up by CLC/TC 61F. If this draft becomes an amendment, CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the s
21、tatus of a national standard without any alteration. This draft amendment was established by CENELEC in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Centra
22、l Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Mal
23、ta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and shall not be referred to as a Europ
24、ean Standard. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:18, Uncontrolled Copy, (c) BSI Draft for vote EN 60745-2-4:2003/FprAC:2008 - 2 - Foreword 1 This draft amendment to the European Standard EN 60745-2-4:2003 was prepared by the Technical 2 Committee CENELE
25、C TC 61F, Safety of hand-held and transportable motor-operated electric tools. 3 It is submitted to the CENELEC formal vote. 4 5 This amendment is proposed to extend Annex ZZ to include the new MD 2006/42/EC. 6 7 This draft amendment should not be ratified until EN 60745-1:2006/FprAC:2008 has been r
26、atified 8 (as a new edition of EN 60745-1). 9 10 After ratification, this amendment shall be merged with the existing European Standard 11 EN 60745-2-4:2003 and its amendments A11:2007 & A1:200X and published as a new edition of 12 EN 60745-2-4, so that it may be listed in the OJEC as supporting the
27、 new MD (2006/42/EC). 13 14 The following dates are proposed: 15 latest date by which the existence of the amendment has to be announced at national level (doa) dor + 6 months latest date by which the amendment has to be implemented at national level by publication of an identical national standard
28、or by endorsement (dop) 2009-12-29 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2009-12-29 This European Standard has been prepared under a mandate given to CENELEC by the European 16 Commission and the European Free Trade Association and cove
29、rs essential requirements of 17 EC Directives 98/37/EC (Machinery Directive), amended by Directive 98/79/EC, and 2006/42/EC. See 18 Annex ZZA and Annex ZZB. 19 Annexes ZA and ZZA and ZZB have been added by CENELEC. 20 This Part 2-4 is to be used in conjunction with EN 60745-1:200X 1). When this Euro
30、pean Standard 21 states “addition“, “modification“ or “replacement“, the relevant text in Part 1 is to be adapted 22 accordingly. 23 1) Future edition 3 of EN 60745-1. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:18, Uncontrolled Copy, (c) BSI Draft for vote - 3
31、- EN 60745-2-4:2003/FprAC:2008 Text of FprAC to EN 60745-2-4:2003 24 Replace the existing Annex ZZ 2)by the following: 25 Annex ZZA 26 (informative) 27 28 Coverage of Essential Requirements of Directive 98/37/EC 29 This European Standard has been prepared under a mandate given to CENELEC by the Euro
32、pean 30 Commission and the European Free Trade Association and within its scope the standard covers all 31 relevant Essential Requirements as given in EC Directive 98/37/EC (Machinery Directive), amended 32 by Directive 98/79/EC. 33 34 Compliance with this standard provides one means of conformity w
33、ith the specified essential 35 requirements of the Directives concerned. 36 37 WARNING: Other requirements and other EC Directives may be applicable to the products falling 38 within the scope of this standard. 39 Annex ZZB 40 (informative) 41 42 Coverage of Essential Requirements of Directive 2006/
34、42/EC 43 This European Standard has been prepared under a mandate given to CENELEC by the European 44 Commission and the European Free Trade Association and within its scope the standard covers all 45 relevant Essential Requirements as given in EC Directive 2006/42/EC (Machinery Directive). 46 47 Co
35、mpliance with this standard provides one means of conformity with the specified essential 48 requirements of the Directives concerned. 49 50 WARNING: Other requirements and other EC Directives may be applicable to the products falling 51 within the scope of this standard. 52 2) Available in EN 60745-2-4:2003/A11:2007. Licensed Copy: London South Bank University, South Bank University, 16/11/2008 12:18, Uncontrolled Copy, (c) BSI