《ABS-109-2007-E2008.pdf》由会员分享,可在线阅读,更多相关《ABS-109-2007-E2008.pdf(2467页珍藏版)》请在三一文库上搜索。
1、 GUIDE FOR BUILDING AND CLASSING HIGH SPEED NAVAL CRAFT 2007 Guide to Color Coding Used in Online Version of the Rules The following summarizes the colors corresponding to Rule Changes, Corrigenda items and editorial changes in the Rules files which are available for download. Rule Changes: Changes
2、effective 1 January 2007 NOTICE NO. 1 March 2007 (effective 1 January 2007) NOTICE NO. 2 July 2007 (effective 1 July 2007) NOTICE NO. 3 November 2007 (effective 1 October 2007) NOTICE NO. 4 January 2008 (effective 1 January 2008) NOTICE NO. 5 July 2008 (effective 1 July 2008) Corrigenda: CORRIGENDA/
3、EDITORIALS 29 January 2007 CORRIGENDA/EDITORIALS 1 March 2007 CORRIGENDA/EDITORIALS 12 April 2007 CORRIGENDA/EDITORIALS 1 July 2007 CORRIGENDA/EDITORIALS 30 January 2008 CORRIGENDA/EDITORIALS 14 July 2008 Editorials: Editorial Changes Copyright American Bureau of Shipping Provided by IHS under licen
4、se with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,-,- GUIDE FOR BUILDING AND CLASSING HIGH SPEED NAVAL CRAFT 2007 NOTICES AND GENERAL INFORMATION American Bureau of Shipping Incorporated by Act of Legis
5、lature of the State of New York 1862 Copyright 2006 American Bureau of Shipping ABS Plaza 16855 Northchase Drive Houston, TX 77060 USA Copyright American Bureau of Shipping Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or
6、networking permitted without license from IHS -,-,- This Page Intentionally Left Blank Copyright American Bureau of Shipping Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,
7、-,- ABS GUIDE FOR BUILDING AND CLASSING HIGH SPEED NAVAL CRAFT . 2007 iii N unavailability of repair facilities; unavailability of essential materials, equipment or spare parts; or delays incurred by action taken to avoid severe weather conditions), consideration may be given for an extension of the
8、 Special Periodical Survey not exceeding three (3) months, provided the craft is attended and the attending Surveyor(s) so recommend(s) after the following has been carried out: Annual Survey; and Re-examination of recommendations; and Progression of the Special Periodical Survey as far as practicab
9、le; and In the case where drydocking is due prior to the end of the class extension, an underwater examination is to be carried out by an approved diving company. An underwater examination by an approved company may be dispensed with in the case of extension of Drydocking Survey not exceeding 36 mon
10、ths interval provided the craft is without outstanding recommendation regarding underwater parts. (1 July 2005) If the craft is at sea on the Special Periodical Survey due date, consideration may be given for an extension of the Special Periodical Survey provided there is documented agreement to an
11、extension prior to the due date, positive arrangements have been made for a Surveyor to attend the craft at the first port of call, and the Bureau is satisfied there is technical justification for an extension; such an extension shall be granted only until arrival at the first port of call after the
12、 due date. However, if owing to “exceptional circumstances” the Special Periodical Survey cannot be completed at the first port of call, the Rule above for an extension of the Special Periodical Survey may be followed, but the total period of extension shall in no case be longer than three (3) month
13、s after the original due date of the Special Periodical Survey. 7.11 (1 July 2005) When a craft is intended for a demolition voyage with any periodical survey overdue, the crafts class suspension may be held in abeyance and consideration may be given to allow the craft to proceed on a single direct
14、ballast voyage from the lay up or final discharge port to the demolition yard. In such cases a short term Class Certificate with conditions for the voyage noted may be issued provided the attending Surveyor finds the craft in satisfactory condition to proceed for the intended voyage. 9 Lifting of Su
15、spension 9.1 (1 July 2005) Class will be reinstated after suspension for overdue surveys upon satisfactory completion of the overdue surveys. Such surveys will be credited as of the original due date. However, the craft is disclassed from the date of suspension until the date class is reinstated. 9.
16、3 (1 July 2005) Class will be reinstated after suspension for overdue recommendations upon satisfactory completion of the overdue recommendation. However, the vessel is disclassed from the date of suspension until the date class is reinstated. Copyright American Bureau of Shipping Provided by IHS un
17、der license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Part 1 Conditions of Classification Chapter 1 Scope and Conditions of Classification Section 2 Suspension and Cancellation of Classificatio
18、n 1-1-2 10 ABS GUIDE FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT . 2007 9.5 Class will be reinstated after suspension for overdue continuous survey items, upon satisfactory completion of the overdue items. 11 Cancellation of Class 11.1 If the circumstances leading to suspension of class are not
19、 corrected within the time specified, the crafts class will be canceled. 11.3 A crafts class is canceled immediately when a craft proceeds to sea without having completed recommendations which were required to be dealt with before leaving port. 11.5 When class has been suspended for a period of thre
20、e (3) months due to overdue Annual, Intermediate, Special, or other periodical surveys required for maintenance of class; overdue Continuous Survey items; or overdue outstanding recommendations, class will be canceled. A longer suspension period may be granted for craft which are either on National
21、Emergency Service, laid up, awaiting disposition of a casualty, or under attendance for reinstatement. Copyright American Bureau of Shipping Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without lic
22、ense from IHS -,-,- ABS GUIDE FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT . 2007 11 P A R T 1 C H A P T E R 1 Scope and Conditions of Classification S E C T I O N 3 Classification Symbols and Notations 1 Classification Symbols Consists of a single mark, single figure or a single letter that rep
23、resents the design features of a craft (e.g. , A1, , etc.). 3 Classification Type Consists of words that describe a crafts specific mission parameters (e.g. Naval Craft). 5 Class Notation Craft which have been built to the satisfaction of the Surveyors to the Bureau to the full requirements of this
24、Guide, or equivalent and approved by the Committee, will be classed and distinguished in the Record by the symbols A1 HSC Naval Craft AMS indicating compliance with the hull and machinery requirements of this Guide. Classification notation consists of words, acronyms, letters and abbreviations that
25、describe a crafts restrictions, service or applicable survey characteristics. For the purpose of ABS classification of a craft, typically, one or more symbols and notations that will denote the crafts classification will be assigned. A typical arrangement of classification will follow the structure
26、below: Copyright American Bureau of Shipping Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Part 1 Conditions of Classification Chapter 1 Scope and Conditions of Classi
27、fication Section 3 Classification Symbols and Notations 1-1-3 12 ABS GUIDE FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT . 2007 A1EQUIPMENT CLASS TYPE STRUCTURAL NOTATION MACHINERY NOTATIONS CONTROL NOTATIONS ABCU AMS, R2N Ice Class, OE HSC Naval Craft Anchoring Equipment A1 Maltese Cross SymbolT
28、able A Table A Table A Table B Table C Table D Table E See:e.g. See:e.g. See:e.g. See:e.g. See:e.g. See:e.g. See:e.g. Copyright American Bureau of Shipping Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permit
29、ted without license from IHS -,-,- Part 1 Conditions of Classification Chapter 1 Scope and Conditions of Classification Section 3 Classification Symbols and Notations 1-1-3 ABS GUIDE FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT . 2007 13 TABLE A Principal Elements SYMBOL DESCRIPTION REFERENCE Th
30、is Maltese Cross symbol will be assigned to vessels for which hull construction and/or manufacture of its machinery and components are carried out under ABS survey. For a vessel, constructed under survey of another recognized Classification Society or Authority, the symbol will be omitted from the c
31、lassification. SVR A1 This symbol indicates compliance with the Hull requirements of the ABS Rules or their equivalent. The symbol A1 is followed by the appropriate vessel type notation. SVR A1 A1 , will signify that the equipment of anchors and cables of the craft is in compliance with the requirem
32、ents of this Guide and any additional optional requirement that may apply, or with the requirements corresponding to the service limitation noted in the crafts classification, which have been specially approved for the limited service. 11 AMS Notation Machinery constructed and installed to the satis
33、faction of the Surveyors to the Bureau to the full requirements of this Guide, when found satisfactory after trial and approved by the Committee, will be classed and distinguished in the Record by the notation AMS. 13 AMS Notation Machinery which has not been constructed and installed under survey t
34、o this Bureau, but which is submitted for classification, will be subjected to a special classification survey. Where found satisfactory and thereafter approved by the Committee, the machinery will be classed and distinguished in the Record by the notation AMS. The mark signifying the survey during
35、construction will be omitted. 15 ACCU or ABCU Notations The automatic and remote-control systems are to be in accordance with the applicable requirements of Part 4, Chapter 9. Copyright American Bureau of Shipping Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 0
36、8/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,-,- ABS GUIDE FOR BUILDING AND CLASSING HIGH-SPEED NAVAL CRAFT . 2007 17 P A R T 1 C H A P T E R 1 Scope and Conditions of Classification S E C T I O N 4 Application 1 Application Limits This Guide is applicable
37、 to high speed naval craft constructed of steel, aluminum, or FRP and having LV not less than 2.36 (1.30) where L is as defined in 3-1-1/3 and V is as defined in 3-2-2/1.1.2. Applicable craft type and length are as follows: Craft Type Applicable Length Mono-hull 2/3XXX A2 High Impact Shock Grade A 2
38、/3XXX B2 High Impact Shock Grade A 2/3XXX C2 High Impact Shock Grade A 100 lbXXXD1 2/3 Wt 100 (4)12.8 (0.5) 150 (6)3.2 (0.125) Bar or Rod 150 (6) and 400 (16)6.4 (0.25) Plate is to be continuously scanned on 200 mm (8 in) grid including one diagonal from each grid. Rounds are to be circumferentially
39、 or helically scanned in a radial orientation, and bars are to be scanned perpendicularly to each side or surface. Material with indication heights greater than that of the comparable reference hole, and material which demonstrates a complete loss of back reflection are to be rejected. 3.9.2Liquid P
40、enetrant Inspection All inspected material is to be free from linear indications, and linearly-disposed (four or more in a line and separated by 1.6 mm (0.063 in) or less) round indications. The acceptance criteria for scattered round indications are shown below. Copyright American Bureau of Shippin
41、g Provided by IHS under license with ABS Licensee=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Part2Supplementary Requirements for Naval Vessels Chapter13Materials for Machinery, Boilers, Pressure Vessels and Pipin
42、g Section22Copper-Nickel Flats and Sections2-13-22 ABS RULE REQUIREMENTS FOR MATERIALS AND WELDING 2000101 Allowable Non-Linear Round Indication Indication Size, in mm (in)Cumulative Number per cm2 (in2) 0.8 (0.031)0.3 (20) 0.8 (0.031) and 1.6 (0.063)0.15 (10) 1.6 (0.063)0 (0) 3.11Cleanliness Prior
43、to any heat treatment, the material surface is to be free from contaminants such as sulfur and sulfur bearing lubricants, marking agents, etc. The material is not to come into contact with mercury or compounds of mercury. 3.13Alloy Identity When specified, each random mill length, prior to cutting t
44、o the ordered length, is to be tested for conformance to the ordered metallurgical alloy, ie alloy C70600 or alloy C71500. Qualitative spot testing is an acceptable method. Material not complying to the ordered alloy is to be rejected. 3.15Sampling When specified, sample pieces are to be selected at
45、 random in accordance with the table below for the visual and dimensional examinations. Number of Pieces in Lot Number of Sample Pieces to be Taken 1to8Entire Lot 9to908 91to15012 151to28019 281to50021 501to1,20027 1,201to3,20035 3,201to10,00038 10,001to35,00046 If one or more sample pieces fail any
46、 inspection or examination, then the lot that it represents is to be rejected. If a lot is rejected as a result of sample inspections, then each piece in the lot may be inspected and those which pass may be accepted. Rejected material may be refurbished by grinding or machining and resubmitted for i
47、nspection. 3.17Marking When specified, marking is to conform to the supplementary requirements, S3 and S4, in ASTM B248, or B249, as appropriate, and the marking is to include the lot number and the contract number. Copyright American Bureau of Shipping Provided by IHS under license with ABS License
48、e=Boeing Co/5910770001 Not for Resale, 08/07/2008 20:31:31 MDTNo reproduction or networking permitted without license from IHS -,-,- Part2Supplementary Requirements for Naval Vessels Chapter13Materials for Machinery, Boilers, Pressure Vessels and Piping Section22Copper-Nickel Flats and Sections2-13-22 102ABS RULE REQUIREMENTS FOR MATERIALS AND WELDING 2000 3.19Order