《ASQ-D61165-1997.pdf》由会员分享，可在线阅读，更多相关《ASQ-D61165-1997.pdf（29页珍藏版）》请在三一文库上搜索。
1、STD-ASQ DbLLb5-ENGL 1797 E 075750b 0002320 575 m ANSI/IEC/ASQ D61165-1997 Application of Markov techniques Approved as an American National Standard by: American Society for Quality Copyright American Society for Quality Provided by IHS under license with ASQ Licensee=IHS Employees/1111111001, User=
2、Wing, Bernie Not for Resale, 04/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- - STD.ASQ DbL1bS-ENGL 1797 075950b 0002321 401 H ANSI/IEC/ASQ D61165-1997 AMERICAN NATIONAL STANDARD Application of Markov Techniques Approved as an American National Standard b
3、y: American Society for Quality An American National Standard Approved on September 16, 1997 American National Standards: An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American National Standard is intended as a guide to aid the
4、manufacturer, the consumer, and the general public. The existence of an American National Standard does not in any respect preclude anyone, whether he or she has approved the standard or not, from manufacturing, purchasing, or using products, processes, or procedures not conforming to the standard.
5、American National Standards are subject to periodic review and users are cautioned to obtain the latest edition. Caution Notice: This American National Standard may be revised or withdrawn at any time. The procedures of the American National Standards Institute require that action be taken to reaffi
6、rm, revise, or withdraw this standard no later than five years from the date of publication. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. Copyright American Society for Quality Provided by
7、IHS under license with ASQ Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- - STD-ASB DbLLb5-ENGL 1997 M 075950b 0002322 348 M O 1995 by IEC Copyright Protection Notice for the ANSI/IEC/
8、ASQ D61165- 1997 Standard. This standard is subject to copyright claims of IEC, ANSI and ASQ. Not for resale. No part of this publication may be reproduced in any form, including an electronic retrieval system, without the prior written permission of ASQ. All requests pertaining to the ANSI/IEC/ASQ
9、D61165-1997 standard should be submitted to ASQ. Note: As used in the document, the term “International Standard” refers to the American National Standard adoption of this and other International Standards. ASQ Mission: T o facilitate continuous improvement and increase customer satisfac- tion by id
10、entifying, communicating, and promoting the use of quality principles, con- cepts, and technologies; and thereby be recognized throughout the world as the leading authority on, and champion for, quality. 1098 7 6 5 4 3 2 1 Printed in the United States of America Printed on acid-free paper Published
11、by: American Societv for Qualitv Quality Press 61 1 East Wisconsin Avenue Milwaukee, Wisconsin 53201 -3005 800-248-1 946 Web site hltp:/www.asq.org Copyright American Society for Quality Provided by IHS under license with ASQ Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18
12、/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- STD-ASQ DbLLbS-ENGL 1997 m 075750b 0002323 289 m ANSI/IEC/ASQ D61165-1997 Contents Page Foreword . 1 Introduction 2 Clause 1 2 3 4 5 6 7 a 9 10 11 12 Scope . 3 Normative references 3 Definitions . 3 Symbols . 4
13、4.1 State-transition diagram 4 4.2 Dependability measures 4 4.3 Example 5 General 5 Assumptions 6 Development of Markov diagrams . 7 7.1 Precautions 7 7.2 Rules 7 7.3 Examples . 8 Evaluation of state-transition diagrams . 11 8.1 General . 11 8.2 Evaluation of reliability 12 8.3 Evaluation of availab
14、ility and maintainability 12 Simplifications and approximations 12 Collapsed state-transition diagram . 13 Reliability and availability expressions for system configurations . 15 Presentation of results . 15 iii Copyright American Society for Quality Provided by IHS under license with ASQ Licensee=I
15、HS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- STIIOASQ DbLLbS-ENGL 1777 075750b 0002324 110 = ANSI/IEC/ASQ D61165-I 997 Annexes A Example: Numerical evaluation of some dependability measures of
16、 a two-unit active redundant system 17 B Tables of reliability and availability expressions for basic system configurations, . 20 C Bibliography 22 iv Copyright American Society for Quality Provided by IHS under license with ASQ Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04
17、/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- STD=ASd DbLlb5-ENGL L797 W 07C750b 0002325 057 m Six Months Rule ANSIA EC/ASQ D61165-1997 Report on Voting Application of Markov Techniques 56(C0)164 Foreword 56 (CO) 1 76 1 ) The IEC (International Electrote
18、chnical Commission) is a world-wide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international cooperation on all questions concerning standardization in the electrical and electronic fields. To th
19、is end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-gov- ernmental
20、organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of the IEC o
21、n technical matters, prepared by technical committees on which all the National Committees having a special interest therein are represented, express, as nearly as possible, an international consensus of opinion on the subjects dealt with. 3) They have the form of recommendations for international u
22、se published in the form of standards, tech- nical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International Standards transparently to the maximum extent possible i
23、n their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. International Standard IEC 1165 has been prepared by IEC Technical Committee No. 56: Dependability. The text of this standard
24、 is based on the following documents: Full information on the voting for the approval of this standard can be found in the report on voting indi- cated in the above table. Annexes A, B and C are for information only. 1 Copyright American Society for Quality Provided by IHS under license with ASQ Lic
25、ensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSIA EC/ASQ D61165-1997 Introduction Several distinct analytical methods of dependability analysis are available, of which Markov analysis
26、is one. IEC 60300-3-1 gives an overview of available methods and their general characteristics. The relative merits of various methods and their individual or combined applicability in evaluating the dependability of a given system or component, should be examined by the analyst prior to deciding on
27、 the use of Markov analysis. For each method, consideration should also be given to the results pro- duced, the data required to perform the analysis, the complexity of analysis, and other identified factors. 2 Copyright American Society for Quality Provided by IHS under license with ASQ Licensee=IH
28、S Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- ANSI/IEC/ASQ 061165-1997 Application of Markov Techniques 1 Scope This International Standard provides guidance on the application of Markov techniq
29、ues to dependability analysis. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were valid. All normative documents are subject to revision, an
30、d parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. Members of IEC and IS0 maintain registers of currently valid International Standards. IEC 60050( 191 ): 1990, International El
31、ectrotechnical Vocabulary (If V), chapter 19 1: Dependability and quality of service. IEC 61 078: (1 991 ), Analysis techniques for dependability-Reliability block diagram method 3 Definitions For the purposes of this International Standard the terms and definitions of IEC 60050(191) apply. In addit
32、ion, the following terms and definitions are used: 3.1 unit: A component or set of components, which function as a single entity. NOTE-AS such, the unit can exist in only two states: functional or failed (see 3.3 and 3.4). For convenience, the term unit state will be used to denote the state of a un
33、it. 3.2 system state: A system state is a particular combination of unit states. NOTE-Several system states may be combined into one state. 3.3 functional state: A system (or unit) state in which the system (or unit) performs the required function. 3.4 failed state: A system (or unit) state in which
34、 the system (or unit) does not perform the required function. NOTE-A system can have several distinguishable failed states. 3.5 transition: A change from one state to another, usually as a result of failure or restoration. NOTE-A transition may be also caused by other events such as human errors, ex
35、ternal events, reconfiguration of software, etc. 3.6 transition probability: The probability of transition between one state and another state. 3 Copyright American Society for Quality Provided by IHS under license with ASQ Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2
36、007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- STD.ASQ DbIILb5-ENGL II797 0 7 5 9 5 0 b 0002328 8bb ANSIA EC/ASQ D61165-1997 3.7 initial state: The system state at time t = O. NOTE-Following a system failure, the system may be restored to the initial state. Ge
37、nerally, a system starts its operation at t = O from the complete functional state in which all units of the system are functioning and transits towards the final system state, which is a failed state, via other system functional states having progressively fewer functioning units. 3.8 absorbing sta
38、te: A state from which, once entered, transitions are not possible. NOTE-Once in an absorbing state, the system will stay there until in effect it is replaced, in its entirety, by a fully functional system. 3.9 restorable system: A system containing units which can fail and then be restored to their
39、 func- tional state, without necessarily causing system failure. NOTES 1 This corresponds to transitions in the state diagram in the direction towards the initial state. For this to be possible, the units concerned will invariably operate in redundant configurations. 2 For a restorable system, depen
40、dability measures such as reliability, MTTFF, and availability are calculated 3.1 O non-restorable system: A system, the state transition diagram of which contains only transitions in the direction towards the final system failure state. NOTE-For a non-restorable system, reliability measures such as
41、 reliability and MTF are calculated 4 Symbols and abbreviations 4.1 Symbols for state-transition diagrams 4.1.1 state symbol: A state is represented by a circle or a rectangle. 4.1.2 state description: The state description is placed inside the state symbol and may take the form of words or alphanum
42、eric characters defining those combinations of failed and functioning units which characterize the state. 4.1.3 state label: A state label is a number in a circle, placed adjacent to the state symbol, or in the absence of a state description, within the symbol itself. NOTE-The state can often be ade
43、quately represented by a circle with the state number. 4.1.4 transition arrow: The transition arrow indicates the direction of a transition (as a result of failure or restoration). 4.1.5 rates: Restoration rates and/or failure rates are written on the transition arrow. 4.2 Other symbols and abbrevia
44、tions Symbols for dependability measures follow those of IEC 50(191), where available. In this standard, the following symbols are used: SymboVab brevia tion Term IEC 50(191)No R(t) reliability NOTE-191-12-01 used the general symbol (t,t,) MllF mean time to failure 191 -1 2-07 4 Copyright American S
45、ociety for Quality Provided by IHS under license with ASQ Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/18/2007 09:49:34 MDTNo reproduction or networking permitted without license from IHS -,-,- MUT MDT Pi( t) At mean time to first failure mean operating time between failur
46、es mean time to restoration failure rate restoration rate instantaneous availability asymtotic availability mean up time mean down time probability of finding the system in state “i” at time t a small time interval NOTE-191-13-02 uses (1) for repair rate NOTE-191-1345 uses A for asyrntotic availabil
47、ity 191 -1 2-06 191 -1 2-09 191 -1 3-08 191 -1 2-02 191-1 1-01 191-11-11 191-11-12 4.3 Example An example of a state-transition diagram, applicable to a one-unit system, is shown in figure 1, h( t)At functional failed state state Figure l-State-transition diagram of a non-restorable one-unit system
48、h(t)At is the probability of a transition between states O and 1 in the small time interval At. Usually how- ever, terms like h(t)At are replaced simply by h. The reason for this is that in this standard h(t) is constant with respect to time (see clause 6) and transition arrows are, by convention, labeled using transition rates rather than transition probabilities. Hence the diagram in figure 1 is frequently drawn in the form shown in figure 2. Figure 2-State-transition diagram (simp