《07-30154654-DC.pdf》由会员分享，可在线阅读，更多相关《07-30154654-DC.pdf（39页珍藏版）》请在三一文库上搜索。
1、a Date: 15 August 2007 Origin: International Latest date for receipt of comments: 30 November 2007 Project no.: 2006/02243 Responsible committee: CPL/34/3 Auxiliaries for lamps Interested committees: Title: Draft BS EN 62386-204 Digital addressable lighting interface Part 204: Particular requirement
2、s for control gears; Low voltage halogen lamps (device type 3) Supersession information: If this document is published as a standard, the UK implementation of it will supersede NONE and partially supersede. NONE If you are aware of a current national standard which may be affected, please notify the
3、 secretary (contact details below). WARNING: THIS IS A DRAFT AND MUST NOT BE REGARDED OR USED AS A BRITISH STANDARD. THIS DRAFT IS NOT CURRENT BEYOND 30 November 2007. This draft is issued to allow comments from interested parties; all comments will be given consideration prior to publication. No ac
4、knowledgement will normally be sent. See overleaf for information on commenting. No copying is allowed, in any form, without prior written permission from BSI except as permitted under the Copyright, Designs and Patent Act 1988 or for circulation within a nominating organization for briefing purpose
5、s. Electronic circulation is limited to dissemination by e-mail within such an organization by committee members. Further copies of this draft may be purchased from BSI Customer Services, Tel: +44(0) 20 8996 9001 or email ordersbsi-. British, International and foreign standards are also available fr
6、om BSI Customer Services. British Standards on CD or Online are available from British Standards Publishing Sales Limited. Tel: 01344 404409 or email bsonlinetechindex.co.uk. Information on the co-operating organizations represented on the committees referenced above may be obtained from the respons
7、ible committee secretary. Cross-references The British Standards which implement International or European publications referred to in this draft may be found via the British Standards Online Service on the BSI web site http:/www.bsi-. Direct tel: 0208 996 7281 Responsible Committee Secretary: Mr S
8、Bounds (BSI) E-mail: simon.boundsbsi- Draft for Public Comment Head Office 389 Chiswick High Road London W4 4AL Telephone: +44(0)20 8996 9000 Fax: +44(0)20 8996 7001 Form 36 Version 7.0 DPC: 07/30154654 DC Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:16:48
9、 GMT+00:00 2007, Uncontrolled Copy, (c) BSI b Introduction This draft standard is based on international discussions in which the UK has taken an active part. Your comments on this draft are welcome and will assist in the preparation of the consequent standard. If no comments are received to the con
10、trary, then the UK will approve this draft. There is a high probability that this text could be adopted by CENELEC as a reference document for harmonization or as a European Standard. Recipients of this draft are requested to comment on the text bearing in mind this possibility. UK Vote Please indic
11、ate whether you consider the UK should submit a negative (with reasons) or positive vote on this draft. Submission The guidance given below is intended to ensure that all comments receive efficient and appropriate attention by the responsible BSI committee. Annotated drafts are not acceptable and wi
12、ll be rejected. All comments must be submitted, preferably electronically, to the Responsible Committee Secretary at the address given on the front cover. Comments should be compatible with Version 6.0 or Version 97 of Microsoft Word for Windows, if possible; otherwise comments in ASCII text format
13、are acceptable. Any comments not submitted electronically should still adhere to these format requirements. All comments submitted should be presented as given in the example below. Further information on submitting comments and how to obtain a blank electronic version of a comment form are availabl
14、e from the BSI web site at: http:/www.bsi- Template for comments and secretariat observations Date: xx/xx/200x Document: ISO/DIS xxxxx 1 2 (3) 4 5 (6) (7) MB Clause No./ Subclause No./ Annex (e.g. 3.1) Paragraph/ Figure/Table/ Note (e.g. Table 1) Type of com- ment Comment (justification for change)
15、by the MB Proposed change by the MB Secretariat observations on each comment submitted 3.1 Definition 1 ed Definition is ambiguous and needs clarifying. Amend to read . so that the mains connector to which no connection . 6.4 Paragraph 2 te The use of the UV photometer as an alternative cannot be su
16、pported as serious problems have been encountered in its use in the UK. Delete reference to UV photometer. Microsoft and MS-DOS are registered trademarks, and Windows is a trademark of Microsoft Corporation. Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:16:
17、48 GMT+00:00 2007, Uncontrolled Copy, (c) BSI FORM CDV (IEC) 2005-09-23 34C/805/CDV COMMITTEE DRAFT FOR VOTE (CDV) PROJET DE COMIT POUR VOTE (CDV) Project number Numro de projet IEC 62386-204 Ed.1 IEC/TC or SC: CEI/CE ou SC: 34C Secretariat / Secrtariat UK/BSI Submitted for parallel voting in CENELE
18、C Soumis au vote parallle au CENELEC Date of circulation Date de diffusion 2007-08-17 Closing date for voting (Voting mandatory for P-members) Date de clture du vote (Vote obligatoire pour les membres (P) 2008-01-18 Also of interest to the following committees Intresse galement les comits suivants -
19、 Supersedes document Remplace le document 34C/742/NP lampes halogne basse tension (dispositifs de type 3) Title: IEC 62386-204 Ed.1: Digital addressable lighting interface Part 204: Particular requirements for control gears; low voltage halogen lamps (device type 3) Note dintroduction - Introductory
20、 note - ATTENTION VOTE PARALLLE CEI CENELEC Lattention des Comits nationaux de la CEI, membres du CENELEC, est attire sur le fait que ce projet de comit pour vote (CDV) de Norme internationale est soumis au vote parallle. Un bulletin de vote spar pour le vote CENELEC leur sera envoy par le Secrtaria
21、t Central du CENELEC. ATTENTION IEC CENELEC PARALLEL VOTING The attention of IEC National Committees, members of CENELEC, is drawn to the fact that this Committee Draft for Vote (CDV) for an International Standard is submitted for parallel voting. A separate form for CENELEC voting will be sent to t
22、hem by the CENELEC Central Secretariat. Copyright 2007 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions. You may not copy o
23、r “mirror“ the file or printed version of the document, or any part of it, for any other purpose without permission in writing from IEC. Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:16:48 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 62386-204 Ed.1/CDV IEC:20
24、0X 2 CONTENTS FOREWORD .3 INTRODUCTION .5 1 Scope.7 2 Normative references .7 3 Definitions 7 4 General Description8 5 Electrical Specifications8 6 Interface power supplies.8 7 Transmission Protocol Structure.8 8 Timing 8 9 Method of Operation.8 10 Declaration of Variables . 10 11 Definition of Comm
25、ands . 10 12 Test procedures . 16 12.4 Test sequence Physical address allocation.16 12.7 Test sequences APPLICATION EXTENDED COMMANDS FOR DEVICE TYPE 3.16 12.7.1 Test sequence APPLICATION EXTENDED QUERY COMMANDS 16 12.7.1.1 Test sequence QUERY FEATURES16 12.7.1.2 Test sequence QUERY SHORT CIRCUIT 17
26、 12.7.1.3 Test sequence QUERY OPEN CIRCUIT.17 12.7.1.4 Test sequence QUERY LOAD DECREASE19 12.7.1.5 Test sequence QUERY LOAD INCREASE .20 12.7.1.6 Test sequence QUERY CURRENT PROTECTOR ACTIVE: Underload.20 12.7.1.7 Test sequence QUERY CURRENT PROTECTOR ACTIVE: Overload.21 12.7.1.8 Test sequence QUER
27、Y THERMAL SHUT DOWN22 12.7.1.9 Test sequence QUERY THERMAL OVERLOAD 23 12.7.2 Test sequence APPLICATION EXTENDED CONFIGURATION COMMANDS 24 12.7.2.1 Test sequence REFERENCE SYSTEM POWER24 12.7.2.2 Test sequence REFERENCE SYSTEM POWER: 100 ms-timeout.26 12.7.2.3 Test sequence REFERENCE SYSTEM POWER: C
28、ommand in-between 27 12.7.2.4 Test sequence REFERENCE SYSTEM POWER: 15 minutes timer.27 12.7.2.5 Test sequence REFERENCE SYSTEM POWER: failed.29 12.7.2.6 Test sequence ENABLE / DISABLE CURRENT PROTECTOR29 12.7.3 Test sequences ENABLE DEVICE TYPE 31 12.7.3.1 Test sequence ENABLE DEVICE TYPE: Applicat
29、ion extended commands.31 12.7.3.2 Test sequence ENABLE DEVICE TYPE: Application extended configuration commands 1 32 12.7.3.3 Test sequence ENABLE DEVICE TYPE: Application ext. configuration commands 2 .33 12.7.6 Test sequences for standard application extended commands 34 12.7.6.1 Test sequences QU
30、ERY EXTENDED VERSION NUMBER .34 12.7.6.2 Test sequence RESERVED APPLICATION EXTENDED COMMANDS.35 A.1.3 Address allocation by physical selection. 36 A.1.5 Reference System Power Measurement . 36 Bibliography36 Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:16
31、:48 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 62386-204 Ed.1/CDV IEC:200X 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DIGITAL ADDRESSABLE LIGHTING INTERFACE Part 204: PARTICULAR REQUIREMENTS FOR CONTROL GEAR LOW VOLTAGE HALOGEN LAMPS (DEVICE TYPE 3) FOREWORD 1) The International Electrotechnical
32、Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co- operation on all questions concerning standardization in the electrical and electronic fields. To this
33、 end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)“). Their preparation is entrusted to technical committees; any IEC National C
34、ommittee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in
35、 accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from a
36、ll interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held
37、responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any dive
38、rgence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication.
39、 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property da
40、mage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this pu
41、blication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all
42、 such patent rights. International Standard IEC 62386-204 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. The text of this standard is based on the following documents: FDIS Report on voting 34C/XX/FDIS 34C/XX/RVD Full informa
43、tion on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:16:48
44、GMT+00:00 2007, Uncontrolled Copy, (c) BSI 62386-204 Ed.1/CDV IEC:200X 4 This part 204 is intended to be used in conjunction with the appropriate parts 1XX, which contain general requirements for the relevant product type (control gear or control devices). IEC 62386 consists of the following parts u
45、nder the general title Digital Addressable Lighting Interface: Part 101: General requirements System. Part 102: General requirements Control gear. Part 103: General requirements Control devices. Part 201: Particular requirements for control gear Fluorescent lamps (device type 0). Part 202: Particula
46、r requirements for control gear Self-contained emergency lighting (device type 1). Part 203: Particular requirements for control gear Discharge lamps (excluding fluorescent lamps) (device type 2). Part 204: Particular requirements for control gear Low voltage halogen lamps (device type 3). Part 205:
47、 Particular requirements for control gear Supply voltage controller for incandescent lamps (device type 4). Part 206: Particular requirements for control gear Conversion from digital into d.c. voltage (device type 5). Part 207: Particular requirements for control gear LED modules (device type 6). Pa
48、rt 208: Particular requirements for control gear Switching function (device type 7). Part 209: Particular requirements for control gear Colour control (device type 8). Part 210: Particular requirements for control gear Sequencer (device type 9). Part 211: Particular requirements for control gear Opt
49、ical control (device type 10). Part 3XX: Particular requirements for control devices. (Reserved for future parts of control devices) Other parts 2XX for other light sources and parts 3XX for control devices are in preparation. Licensed Copy: London South Bank University, London South Bank University,