《BS-EN-1028-1-2002-A1-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-1028-1-2002-A1-2008.pdf（34页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 1028-1:2002 +A1:2008 Fire-fighting pumps Fire-fighting centrifugal pumps with primer Part 1: Classification General and safety requirements ICS 13.220.10 ? Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Copy, (c) BSI BS EN 10
2、28-1:2002+A1:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 September 2002 BSI 2008 ISBN 978 0 580 60401 0 National foreword This British Standard is the UK implementation of EN 1028-1:2002+A1:2008. It supersedes BS EN 1028-1:2002 wh
3、ich is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to CEN text carry the number of the CEN amendment. For example, text altered by CEN amendment A1 is indicated by !“. The UK participation in its preparation was
4、 entrusted by Technical Committee FSH/17, Fire brigade equipment, to Subcommittee FSH/17/4, Pumps. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are
5、responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda issued since publication DateComments 31 October 2008Implementation of CEN amendment A1:2008 Licensed Copy: London South Bank University, South Bank Univer
6、sity, 16/11/2008 11:59, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1028-1:2002+A1 July 2008 ICS 13.220.10 Supersedes EN 1028-1:2002 English Version Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 1: Classification - General and safety req
7、uirements Pompes usage incendie - Pompes centrifuges usage incendie avec dispositif damorage - Partie 1 : Classification - Prescriptions gnrales et de scurit Feuerlschpumpen - Feuerlschkreiselpumpen mit Entlftungseinrichtung - Teil 1: Klassifizierung - Allgemeine und Sicherheitsanforderungen This Eu
8、ropean Standard was approved by CEN on 8 April 2002 and includes Amendment 1 approved by CEN on 6 June 2008. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any altera
9、tion. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by trans
10、lation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, German
11、y, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG M
12、anagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1028-1:2002+A1:2008: E Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Co
13、py, (c) BSI EN 1028-1:2002+A1:2008 (E) 2 Contents Foreword4 0 Introduction5 1 Scope 6 2 Normative references7 3 Terms and definitions .8 3.1 Pumps and their applications.8 3.2 Suction heights9 3.3 Pressures9 3.4 Delivery rates11 3.5 Power 11 3.6 Speed of rotation .12 3.7 Efficiencies.12 4 List of si
14、gnificant hazards 12 5 Safety requirements and/or protective measures14 5.1 General14 5.2 Special requirements 15 5.2.1 Mechanical hazards.15 5.2.2 Electrical hazards 16 5.2.3 Thermal hazards 16 5.2.4 Hazards from neglecting ergonomic design principles 17 5.2.5 Hazards due to breakdown and/or incorr
15、ect installation of protection devices.17 6 General and performance requirements .18 6.1 Design.18 6.2 Materials .18 6.3 Nominal delivery pressure18 6.4 Nominal delivery rate 18 6.5 Geodetic nominal suction height.18 6.6 Closing pressure18 6.7 Primer19 6.8 Drainability .19 6.9 Shut off valves and pu
16、mp connections.19 6.10 Pump inlet screen19 6.11 Low temperature starting19 6.12 Very low temperature behaviour19 6.13 Operating controls.19 6.14 Additional equipment19 6.15 Pump integrity protection equipment19 6.16 Efficiency20 6.17 Guarantee points .20 6.18 Special tools.20 7 Verification of the s
17、afety requirements and/or protective measures.20 8 Verification of the general and performance requirements 20 9 Classification and brief designation21 10 Designation 22 11 Information for use22 11.1 General22 11.2 Signals and warning devices22 11.3 Accompanying documents.22 11.3.1 General22 BS EN 1
18、028-1:2002+A1:2008 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Copy, (c) BSI EN 1028-1:2002+A1:2008 (E) 3 11.3.2 Contents .22 11.4 Marking.27 Annex ZA (informative) !Relationship between this European Standard and the Essential Requirements of E
19、U Directive 98/37/EC“.28 Annex ZB (informative) !Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC“.29 Bibliography30 BS EN 1028-1:2002+A1:2008 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Copy,
20、 (c) BSI EN 1028-1:2002+A1:2008 (E) 4 Foreword This document (EN 1028-1:2002+A1:2008) has been prepared by Technical Committee CEN/TC 192 “Fire service equipment“, the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication
21、of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. This document includes Amendment 1, approved by CEN on 2008-06-06. This document supersedes EN 1028-1:2002. The start and finish of text introdu
22、ced or altered by amendment is indicated in the text by tags ! “. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). !For relationship with EU Directive(s), see infor
23、mative Annexes ZA and ZB, which are integral parts of this document.“ This part of this European Standard shall be applied only in conjunction with part 2 of EN 1028 “Verification of general and safety requirements“. EN 1028 “Fire-fighting pumps Fire-fighting centrifugal pumps with primer“ comprises
24、 two parts: Part 1: Classification General and safety requirements; Part 2: Verification of general and safety requirements. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belg
25、ium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 1028-1:2002+A1:2
26、008 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Copy, (c) BSI EN 1028-1:2002+A1:2008 (E) 5 0 Introduction This European Standard is a type C standard as stated in EN 292 and EN 1070. The machinery concerned and the extent to which hazards, hazar
27、dous situations and events are covered are indicated in the scope of this standard. Where provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precedence over the provisions of the other standards, for mach
28、ines that have been designed and built in accordance with the provisions of this type C standard. This Standard has been prepared as a harmonized standard to provide one means of conformity with essential requirements of the Machinery Directive and associated EFTA Regulations. While producing this s
29、tandard it was assumed that: a) only trained persons operate the machine; b) components without specific requirements are: 1) designed in accordance with the usual engineering practice and calculation codes, including all failure modes; 2) of sound mechanical construction; 3) of materials with adequ
30、ate strength and of suitable quality; 4) of materials free of defects; NOTE General hazards due to hydraulic and pneumatic equipment are dealt with in standards for common use such as EN 982, EN 983. c) harmful materials (e.g. asbestos) are not used as part of the machine; d) components are kept in
31、good repair and working order, so that the required characteristics remain; e) by design of the load bearing elements, a safe operation of the machine is assured for loading, from 0 % to 100 % of the rated possibilities and during the tests; f) to ensure the correct functioning of the equipment, the
32、 ambient temperature is maintained between -15 C (for special conditions, -30 C; see 6.12) and 40 C; NOTE Directly around the pump the temperature can be 20 C higher. g) the manufacturer and the user have agreed the features of the machinery and the operating conditions; h) the place of installation
33、 enables safe usage of the machine. BS EN 1028-1:2002+A1:2008 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Copy, (c) BSI EN 1028-1:2002+A1:2008 (E) 6 1 Scope This standard applies for centrifugal pumps with priming devices for fire-fighting use s
34、upplied separately without driver and couplings. Fire-fighting centrifugal pumps with primer are defined as terminated by their inlet and outlet connec- tions as well as by their shaft ends. This standard applies for fire-fighting centrifugal pumps with priming devices for use under ambient temperat
35、ures between -15 C and 40 C. NOTE For special conditions, -30 C; see 6.12. This standard does not apply to fire-fighting centrifugal pumps with primer of which the only power source is directly applied manual effort. This standard specifies the classification and general requirements for fire-fighti
36、ng centrifugal pumps with priming devices with a nominal delivery rate of up to 6000 l/min. This standard deals with significant hazards listed in clause 4, hazardous situations and events during the commissio- ning, operation and maintenance of fire-fighting centrifugal pumps with priming devices,
37、used as intended and under the conditions foreseen by the manufacturer or the manufacturers authorized representative. In addition, fire-fighting centrifugal pumps with priming devices shall conform as appropriate to EN 292 for hazards not covered by this standard. This standard does not deal with t
38、he detailed verification of general and safety requirements and/or protective measures. These are covered in EN 1028-2 “Verification of general and safety requirements“. This standard does not deal with the technical safety requirements for the design or manufacture of drivers or of auxiliary equipm
39、ent. It does not cover risks directly arising from means provided for the portability, transportability, and mobility of pump units during or between periods of operation, or requirements for transmission shafts linking self- propelled machinery to a pump. In addition, this standard does not cover:
40、operation subject to special rules (e. g. potentially explosive atmospheres); hazards occuring due to decommissioning; hazards occuring during handling; hazards occuring when in use (e. g. on public roads). This standard does not apply to fire-fighting centrifugal pumps with primer that are manufact
41、ured before the date of publication by CEN of this standard. BS EN 1028-1:2002+A1:2008 Licensed Copy: London South Bank University, South Bank University, 16/11/2008 11:59, Uncontrolled Copy, (c) BSI EN 1028-1:2002+A1:2008 (E) 7 2 Normative references This European Standard incorporates by dated or
42、undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only
43、when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 292-1:1991, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology. EN 292-2:1991, Safety of
44、 machinery Basic concepts, general principles for design Part 2: Technical principles and specifications. EN 292-2/A1:1995, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and specifications; Amendment A1. EN 294:1992, Safety of machinery Safety distanc
45、es to prevent danger zones being reached by the upper limbs. EN 349:1993, Safety of machinery Minimum gaps to avoid crushing of parts of the human body. EN 547-2:1996, Safety of machinery Human body measurements Part 2: Principles for determining the dimensions required for access openings. EN 547-3
46、:1996, Safety of machinery Human body measurements Part 3: Anthropometric data. EN 842:1996, Safety of machinery Visual danger signals General requirements, design and testing. EN 894-1:1997, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General
47、 principles for human interactions with displays and control actuators. EN 894-2:1997, Safety of machinery Ergonomics requirements for the design of displays and control actuators - Part 2: Displays. EN 894-3:2000, Safety of machinery Ergonomics requirements for the design of displays and control ac
48、tuators Part 3: Control actuators. EN 953:1997, Safety of machinery General requirements for the design and construction of fixed and movable guards. EN 1028-2:2002, Fire-fighting pumps Fire-fighting centrifugal pumps with primer Part 2: Verification of general and safety requirements. EN 1050:1996,
49、 Safety of machinery Principles for risk assessment. EN 1070:1998, Safety of machinery Terminology. EN 25199:1992, Technical specifications for centrifugal pumps Class II (ISO 5199:1986). EN 60204-1:1997, Safety of machinery Electrical equipment of machines Part 1: General requirements (IEC 60204-1:1997). EN 60529:1991+A1:2000, Degrees of protection provided by enclosures (IP code) (IEC 60529:1989) + Amendm