《BS-EN-12209-2003.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12209-2003.pdf（58页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 12209:2003 Incorporating Corrigendum No. 1 Building hardware Locks and latches Mechanically operated locks, latches and locking plates Requirements and test methods The European Standard EN 12209:2003 has the status of a British Standard ICS 91.190 ? BS EN 12209:2003 This Brit
2、ish Standard, was published under the authority of the Standards Policy and Strategy Committee on 18 December 2003 BSI September 2006 ISBN 0 580 43143 6 National foreword This British Standard is the official English language version of EN 12209:2003, including Corrigendum December 2005. It supersed
3、es BS 5872:1980 which is withdrawn. The UK participation initspreparation was entrusted byTechnicalCommittee B/538, Doors, windows, shutters, hardware and curtain walling, to Subcommittee B/538/4, Building hardware, which has the responsibility to: A list of organizations represented on this subcomm
4、ittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “ International Standards Correspondence Index” , or by using the
5、 “ Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from l
6、egal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK.
7、 Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 55 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. 16436September 2006 Replace
8、ment of Table 3, 8.1 and Corrigendum No. 1Tables ZA.1 and ZA.3 DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 12209 December 2003 ICS 91.190 English version Building hardware - Locks and latches - Mechanically operated locks, latches and locking plates - Requirements and test meth
9、ods Quincaillerie pour le btiment - Serrures - Serrures mcaniques et gches - Exigences et mthodes dessai Schlsser und Baubeschlge - Schlsser - Mechanisch bettigte Schlsser und Schliebleche - Anforderungen und Prfverfahren This European Standard was approved by CEN on 27 June 2003. CEN members are bo
10、und to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the
11、Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as
12、the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN C
13、OMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12209:2003 E EN 12209:2003 (E) 2
14、Contentspage Foreword.3 1Scope4 2Normative references4 3Terms, definitions, symbols and units4 3.1Terms and definitions.4 3.2Symbols, units and abbreviated terms.6 4Classification.8 4.1General.8 4.2Classification for mechanically operated locks, latches and locking plates9 5Requirements 13 5.1Genera
15、l.13 5.2Category of use.13 5.3Durability14 5.4Door mass and closing force.15 5.5Suitability for use on fire / smoke doors.15 5.6Safety15 5.7Corrosion resistance and temperature.15 5.8Security15 5.9Field of door application 20 5.10Type of key operation and locking21 5.11Type of spindle operation 21 5
16、.12Key identification requirement 22 6Test methods.23 6.1General.23 6.2Category of use.25 6.3Durability26 6.4Door mass and closing force.28 6.5Suitabilty for use on fire / smoke doors28 6.6Safety28 6.7Corrosion resistance and temperature.28 6.8Security29 6.9Field of door application 32 6.10Type of k
17、ey operation and locking32 6.11Spindle operation33 6.12Key identification 34 7Marking.34 8Evaluation of conformity34 8.1Initial type test.34 8.2Factory production control 35 8.3Further testing of samples.35 Annex A (normative) Fire resistance requirement36 Annex B (normative) Illustration of test ap
18、paratus for locks and latches37 Annex C (normative) Test sampling and sequencing for locks and latches46 Annex D (informative) Field of door application49 Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive (89/106/EEC)50 Bibli
19、ography .55 EN 12209:2003 (E) 3 Foreword This document (EN 12209:2003) has been prepared by Technical Committee CEN /TC 33, “Doors, windows, shutters, building hardware and curtain walling“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national sta
20、ndard, either by publication of an identical text or by endorsement, at the latest by June 2004, and conflicting national standards shall be withdrawn at the latest by September 2005. No existing European Standard is superseded. This European Standard is one of a series of European Standards dedicat
21、ed to building hardware products. Complementing this European Standard is a draft European Standard for electromechanically operated locks and locking plates (prEN 14846) and a draft European Standard for mechanically operated multi-point locks (WI 00033250). This document has been prepared under a
22、mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative annex ZA, which is an integral part of this document. Annexes A, B and C are normative. Annex D is i
23、nformative. The performance tests incorporated in this standard are considered to be reproducible and as such will provide a consistent and objective assessment of the performance of these products throughout CEN Member States This document includes a Bibliography. According to the CEN/CENELEC Inter
24、nal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, S
25、pain, Sweden, Switzerland and the United Kingdom. EN 12209:2003 (E) 4 1 Scope This European Standard specifies requirements and test methods for durability, strength, security, and function of mechanically operated locks and latches and their locking plates for use in doors, window doors and entranc
26、e doors in buildings. Locks, latches and their locking plates used in fire resistant and/or smoke control door assemblies require additional attributes in order to comply with the Essential Requirement “Safety in case of fire“ either independently or as a part of a complete assembly. Additional requ
27、irements for locks and latches and their locking plates used on fire resistant and/or smoke control door assemblies are specified in annex A. The following locking devices and associated products are not covered by this European Standard: cylinders for locks, handles, electro-mechanically operated l
28、ocks and striking plates, multi-point locks and their locking plates, locks for windows, padlocks, locks for safes, furniture locks and prison locks. NOTEA lock meeting this standard can at the same time be part of an exit device according to EN 179 or EN 1125. 2 Normative references This European S
29、tandard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications appl
30、y to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN 1634-1, Fire resistance tests for door and shutter assemblies - Part 1: Fire doors and shutters. EN 1670:1998
31、, Building hardware Corrosion resistance Requirements and test methods. ISO 10899, High-speed steel two-flute twist drills Technical specifications. 3 Terms, definitions, symbols and units 3.1 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply
32、. 3.1.1 bolt movable part of a lock or latch that usually engages a component fixed to a frame, and withdraws into the case 3.1.2 bored latch set fastener that comprises an integral assembly of door furniture with a tubular latch 3.1.3 bored lock set fastener that comprises an integral assembly of d
33、oor furniture with a tubular lock EN 12209:2003 (E) 5 3.1.4 case part of a lock or latch in which the lock mechanism and/or latch action is housed 3.1.5 cylinder device, usually separate from but engaging with its associated lock or latch, that contains the parts operated by the key 3.1.6 cylinder l
34、ock lock in which the lock mechanism is operated by one or more cylinders 3.1.7 deadbolt bolt that is operated in both directions by a key, handle and/or thumb turn 3.1.8 detaining element part of a movable member which is moved by the key into a pre-determined position in order for the bolt to be a
35、ble to move into an opening position 3.1.9 differ variation between lock mechanism of similar design, achieved by the detaining elements, which allows each lock to be operated only by its own key 3.1.10 effective differ difference between lock or key recognition systems of similar design achieved on
36、ly by the detaining elements which allows each lock or key recognition systems to be operated only by its own key. The number of effective differs is equal to the number of theoretical differs after deduction of the differs suppressed by the manufacturer due to technical constraints 3.1.11 follower
37、part of a lock that operates the bolt or bolts when turned by a spindle 3.1.12 forend part of a case through which the lock is fixed to the door and through which the latch bolt and/or deadbolt pass 3.1.13 key device that is removable and portable and is used to operate the lock or latch 3.1.14 latc
38、h self engaging fastener which secures a movable component (e.g. door) in a closed position and which can be released by hand 3.1.15 latch action arrangement and performance of the constituent parts that operate a latch bolt 3.1.16 latch bolt moving part of the latch that engages the locking plate E
39、N 12209:2003 (E) 6 3.1.17 lock fastener which secures a movable component in a closed position within an opening and which is operated by a key or other device 3.1.18 locking plate component, fixed to a frame to engage a bolt, or bolts NOTEAlternative terms for this are strike plate, keep or staple.
40、 3.1.19 locking snib device, usually in the form of a small lever or knob, which can be operated to prevent the bolt from being thrown or withdrawn, or to change the function of a lock or latch 3.1.20 lock mechanism constituent parts of a lock that operate the deadbolt and, where required, provide t
41、he differs 3.1.21 multi-point lock lock comprising more than one locking point between door leaf and frame, inter-linked and centrally controlled 3.2 Symbols, units and abbreviated terms For the purposes of this European Standard, the following symbols shown in Table 1 and Figure 1 shall apply. EN 1
42、2209:2003 (E) 7 Table 1 Symbols Symbol Test parameter DefinitionUnit F1Lateral force on latch bolt (strength test)kN F2Return force of latch boltN F3Lateral force on latch bolt and locking plate (durability test)N F4Lateral force on deadbolt and locking platekN F5End load on deadbolt or locking plat
43、ekN F6Pull force on hook/claw bolt or locking platekN F7Disengaging force on hook/claw boltkN F8Force on locating device or lifting force on locking platekN F9Pull force on knobs akN F10Door closing force (operating requirement) bN F11Door closing force (durability test) bN L1Deadbolt projection cmm
44、 L2Resulting projection cmm L3Internal depth of box at locking plate dmm M1Torque to withdraw the latch bolt with keyNm M2Torque to withdraw the latch bolt with handle, spring handle or knobNm M3Torque to operate the deadbolt with keyNm M4Torque to operate the deadbolt with handleNm M5Forcing torque
45、 on the followerNm M7Torque on keyNm M8Restoring torqueNm M9Forcing torque on knobs or lever handlesNm M10Torque resistance of Rim lock with lockable handle / knobNm N1Number of detaining elements- N2Number of effective differs- N3Number of step heights on key- TTemperatureC tDrill timemin a See Fig
46、ure B.6. b See Figure B.2. c See Figure B.4. d See Figure B.8. EN 12209:2003 (E) 8 Figure 1 Application of forces and torques to locks and latches classification 4 Classification 4.1 General 4.1.1For the purpose of this European Standard, mechanically operated locks and latches shall be classified a
47、ccording to the eleven character classification system described in 4.2.1 to 4.2.11. Locking plates intended to be sold separately from the lock or latch may be coded accordingly using the same classification system but with grades only in those categories that are relevant to locking plates. 4.1.2A
48、ll locks regardless of classification shall fulfil 5.1.1 and 5.1.2. EN 12209:2003 (E) 9 4.2 Classification for mechanically operated locks, latches and locking plates Table 2 Classification 1234567891011 Category of use Durability and load on latch bolt Door mass and closing force Suitability for us
49、e on fire / smoke doors SafetyCorrosion resistance and temperature Security and drill resistance Field of door application Type of key operation and locking Type of spindle operation Key identification 4.2.1 Category of use (first digit) Three grades are identified in accordance with requirements stated in 5.2.1 to 5.2.4. grade 1: for use by people with a high incentive to exercise care and with a small chance of misuse, e.g. residential doors. grade 2: for use by people wi