《BS-EN-12373-7-1999.pdf》由会员分享，可在线阅读，更多相关《BS-EN-12373-7-1999.pdf（8页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 12373-7:1999 The Eu
2、ropean Standard EN 12373-7:1998 has the status of a British Standard ICS 25.220.20; 77.120.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Aluminium and aluminium alloys Anodizing Part 7: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss o
3、f mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 Apri
4、l 1999 BSI 04-1999 ISBN 0 580 32027 8 BS EN 12373-7:1999 Amendments issued since publication Amd. No.DateText affected National foreword This British Standard is the English language version of EN 12373-7:1998. The UK participation in its preparation was entrusted to Technical Committee STI/32, Anod
5、ic oxidation coatings on aluminium, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European develo
6、pments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalo
7、gue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correc
8、t application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 5 and a back cover. CEN European Committee for Standardization Comite Europe en de
9、 Normalisation Europa isches Komitee fu r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1998 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 12373-7:1998 E EUROPEAN STANDARDEN 12373-7 NORME EUROPE ENNE EUROPA ISC
10、HE NORM November 1998 ICS Descriptors: surface treatment, anodizing, aluminium, aluminium alloys, sealing, quality control, destructive tests, immersion tests, solution, phosphoric acid, measurements, mass losses English version Aluminium and aluminium alloys Anodizing Part7: Assessment of quality o
11、f sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment Aluminium et alliages daluminium Anodisation Partie 7: Evaluation de la qualite des couches anodiques colmate es par mesurage de la perte de masse
12、apre s immersion en solution phosphochromique avec traitement acide pre alable Aluminium und Aluminiumlegierungen Anodisieren Teil 7: Pru fung der Qualita t von verdichteten, anodisch erzeugten Oxidschichten durch Bestimmung des Massenverlustes nach Eintauchen in Chromphosphorsa ure-Lo sung mit vorh
13、eriger Sa urebehandlung This European Standard was approved by CEN on 5 November 1998. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists
14、 and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the respons
15、ibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Nethe
16、rlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Page 2 EN 12373-7:1998 BSI 04-1999 Foreword This European Standard has been prepared by Technical Committee CEN/TC 132, Aluminium and aluminium alloys, the Secretariat of which is held by AFNOR. This European Standard shall be
17、given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 1999, and conflicting national standards shall be withdrawn at the latest by May 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations o
18、f the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. In this standard, annex A is no
19、rmative. EN 12373, Aluminium and aluminium alloys Anodizing, comprises the following parts: Part 1: Method for specifying decorative and protective anodic oxidation coatings on aluminium; Part 2: Determination of mass per unit area (surface density) of anodic oxidation coatings Gravimetric method; P
20、art 3: Determination of thickness of anodic oxidation coatings Non-destructive measurement by split-beam microscope; Part 4: Estimation of loss of absorptive power of anodic oxidation coatings after sealing by dye spot test with prior acid treatment; Part 5: Assessment of quality of sealed anodic ox
21、idation coatings by measurement of admittance; Part 6: Assessment of quality of sealed anodic oxidation coatings by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution without prior acid treatment; Part 7: Assessment of quality of sealed anodic oxidation coatings
22、 by measurement of the loss of mass after immersion in phosphoric acid/chromic acid solution with prior acid treatment; Part 8: Determination of the comparative fastness to ultra-violet light and heat of coloured anodic oxidation coatings; Part 9: Measurement of wear resistance and wear index of ano
23、dic oxidation coatings using an abrasive wheel wear test apparatus; Part 10: Measurement of mean specific abrasion resistance of anodic oxidation coatings using an abrasive jet test apparatus; Part 11: Measurement of specular reflectance and specular gloss of anodic oxidation coatings at angles of 2
24、08, 458, 608 or 858; Part 12: Measurement of reflectance characteristics of aluminium surfaces using integrating-sphere instruments; Part 13: Measurement of reflectivity characteristics of aluminium surfaces using a goniophotometer or an abridged goniophotometer; Part 14: Visual determination of ima
25、ge clarity of anodic oxidation coatings Chart scale method; Part 15: Assessment of resistance of anodic oxidation coatings to cracking by deformation; Part 16: Check for continuity of thin anodic oxidation coatings Copper sulfate test; Part 17: Determination of electric breakdown potential; Part 18:
26、 Rating system for the evaluation of pitting corrosion Chart method; Part 19: Rating system for the evaluation of pitting corrosion Grid method. Contents Page Foreword2 1Scope3 2Principle3 3Reagents3 4Apparatus3 5Preparation of test piece3 6Procedure3 7Expression of results4 8Test report4 Annex A (n
27、ormative) Method for the drying of samples5 Page 3 EN 12373-7:1998 BSI 04-1999 1) See foreword. 1 Scope This part of this European Standard specifies a method of assessing the quality of sealed anodic oxidation coatings on aluminium and its alloys by measurement of the loss of mass after immersion i
28、n phosphoric acid/chromic acid solution with prior acid treatment. A related standard (EN 12373-61) describes the same method used without prior acid treatment. The method is particularly applicable to anodic oxidation coatings intended for architectural purposes. For less severe applications, the m
29、ethod described in EN 12373-61)may be more suitable. The method is not applicable to: hard-type anodic oxidation coatings which normally are not sealed; anodic oxidation coatings that have been sealed only in dichromate solutions; anodic oxidation coatings produced in chromic acid solutions; anodic
30、oxidation coatings that have undergone a treatment to render them hydrophobic. The method is destructive and can serve as a reference method in case of doubt or dispute regarding the results of the test for loss of absorptive power (EN 12373-41), or the measurement of admittance (EN 12373-51). 2 Pri
31、nciple An unsealed anodic oxidation coating on aluminium is dissolved rapidly by acid media, whereas a well-sealed coating will withstand long immersion without appreciable attack. 3 Reagents Use only reagents of recognized analytical grade and distilled water, or water of equivalent purity. 3.1 Pre
32、dip. Aqueous solution containing, per litre, 650 ml nitric acid (r20= 1,4 g/ml). 3.2 Test solution. Aqueous solution containing, per litre, 35 ml phosphoric acid (r20= 1,7 g/ml) and 20 g chromium(VI) oxide. 4 Apparatus Usual laboratory apparatus and glassware, together with the following. Laboratory
33、 balance, capable of weighing to an accuracy of 0,1 mg. 5 Preparation of test piece Cut a test piece from the material to be tested, avoiding contact areas, such that there is an area of approximately 1 dm2, but not less than 0,5 dm2, of significant surface area. Normally, the mass of the test piece
34、 should not exceed 200 g. For hollow extrusions, take the test piece from the end of the sections where the total surface area has an anodic oxidation coating (due to the throwing power of the anodizing electrolyte). NOTEIn special cases, such as certain types of jigging, small hollow sections etc.,
35、 it will be necessary to remove the anodic oxidation coating from the inside surface and to carry out the test on the coating on the outer surface of the extrusion. 6 Procedure 6.1 Measure the total coated area of the test piece (excluding cut edges and other uncoated surfaces). NOTEThe predip and t
36、he test solution do not attack bare metal, and it is not necessary to take uncoated surfaces into account. Remove any surface bloom from the test piece by rubbing with a dry cloth. 6.2 Degrease the test piece in an organic solvent, e.g. acetone or ethanol 96 % (V/V), at room temperature according to
37、 the method described in A.1. 6.3 Dry the test piece thoroughly (see A.1 and A.2) and weigh immediately to the nearest 0,1 mg (m1). 6.4 Immerse the test piece completely, standing it upright, in the predip (see 3.1) and leave for 10 min at a temperature of 19 8C1 8C. 6.5 Take the test piece from the
38、 predip and rinse thoroughly, first under running water and then in distilled water. 6.6 Immerse the test piece completely, standing it upright, in the test solution (see 3.2) and leave for exactly 15 min at a constant temperature of 38 8C1 8C. NOTEUniformity of temperature within the test solution
39、is very important; this can be achieved by using a water-bath and stirring continuously. Do not use the test solution after more than 10 dm2of anodized surface have been treated per litre of solution. Do not use test solution which has been in contact with materials other than anodized aluminium or
40、its alloys. 6.7 Take the test piece from the test solution and rinse thoroughly, first under running water and then in distilled water. Dry the test piece as indicated in annex A and weigh immediately to the nearest 0,1 mg (m2). 6.8 During the operations described in 6.2 to 6.7, avoid touching the t
41、est piece with bare hands. Take extreme care that the two drying operations in 6.3 and 6.7 are carried out in the same reproducible way, and avoid heating to temperatures above 60 8C. Page 4 EN 12373-7:1998 BSI 04-1999 7 Expression of results Calculate the loss in mass per unit area of surface, dA,
42、in milligrams per square decimetre, using the equation: (1)dA= m12 m2 A where m1is the mass, in milligrams, of the test piece before immersion in the predip and test solution; m2is the mass, in milligrams, of the test piece after immersion in the predip and test solution; Ais the coated surface area
43、 of the test piece, in square decimetres, in contact with the predip and test solution. 8 Test report The test report shall contain at least the following information: a) the type and identification of the product tested; b) a reference to this European Standard; c) how the significant surface area
44、has been determined; d) whether the test solution has been stirred; e) the result of the test (see clause 7); NOTEAcceptance levels will normally be specified in the relevant product specification. f) any deviation, by agreement or otherwise, from the procedure specified; g) the date of the test. Pa
45、ge 5 EN 12373-7:1998 BSI 04-1999 Annex A (normative) Method for the drying of samples A.1 Degrease the test piece by gentle agitation for 30 s in a suitable organic solvent at room temperature; remove; leave for 5 min in the ambient atmosphere (pre-drying); place in a drying oven preheated to 60 8C
46、and leave for exactly 15 min with the coated surfaces standing upright. WARNING NOTEWhere organic solvents are used, carry out the degreasing operation and the pre-drying in a well-ventilated area to minimize exposure to solvent vapour. A.2 Allow the test piece to cool for 30 min over silica gel in
47、a closed desiccator. A.3 After the acid treatment and rinsing (see 6.7), repeat operations A.1 and A.2, omitting the treatment in the organic solvent. BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
48、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards i
49、n Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee r