《BS-EN-160200-1-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-160200-1-1998.pdf（34页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 160200-1:1998 Harmonized system of quality assessment for electronic components Sectional specification: Microwave modular electronic units of assessed quality Part 1: Capability approval procedure The European Standard EN 160200-1:1997 has the status of a British Standard ICS
2、 31.020 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 160200-1:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and co
3、mes into effect on 15 May 1998 BSI 04-1999 ISBN 0 580 29794 2 National foreword This British Standard is the English language version of EN 160200-1:1997 published by the European Electronic Components Committee (CECC) of the European Committee for Electrotechnical Standardization (CENELEC). The UK
4、participation in its preparation was entrusted to Technical Committee EPL/500, Modular Electronic Units (MEUs), which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for cha
5、nge, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or E
6、uropean publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the n
7、ecessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, th
8、e EN title page, pages 2 to 28 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun
9、sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 160200-1:1998 BSI 04-1999i Contents Page National forewordInside front cover Foreword2 Text of EN 160200-13 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
10、 ii blank Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 160200-1 December 1997 Descriptors: Modular electronic units, capability approval, sectional specification English version Section
11、al specification: Microwave modular electronic units of assessed quality Part 1: Capability approval procedure Rahmenspezifikation: Elektronische Mikrowellenmodule mit bewerteter Qualitt Teil 1: Befhigungsanerkennung This European Standard was approved by CENELEC on 1994-04-15. CENELEC members are b
12、ound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the
13、 Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the sa
14、me status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC
15、European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1997 CENELEC All rights of exploitation in any form and by any means reserved worldwide fo
16、r CENELEC members. Ref. No. EN 160200-1:1997 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 160200-1:1997 BSI 04-1999 2 Foreword This sectional specification has been prepared by the United Kingdom under the single originator procedure
17、 for approval and publication of CECC specifications (see RP 11-V). It is to be used for the assessment of Microwave Modular Electronic Units (MMEUs) within the CECC capability approval scheme. The content is in accordance with the generic specification for Modular Electronic Units (MEUs); EN 160000
18、 and meets the requirements of Rule of Procedure 14 (RP 14). This sectional specification is based, wherever possible, on the publications of the International Electrotechnical Commission. It includes, as (blank) examples, formats for a capability qualifying component specification and customers det
19、ail specification (CDS). The use of this sectional specification is as follows: a) a potential customer makes an enquiry to the manufacturer for a Microwave Modular Electronic Unit within the scope of his capability published in CECC 00200; b) the specification is negotiated between the manufacturer
20、 and the customer, until an agreed customers detail specification is finalized; c) the Microwave Modular Electronic Unit is inspected and released in accordance with the agreed Customers Detail Specification. In order to facilitate the review of the document, the “index of electrical test methods” h
21、as been published as Part 2 of this sectional specification. The text of the draft based on document CECC(Secretariat)3317 was submitted to the formal vote; together with the voting report, circulated as document CECC(Secretariat)3522, it was approved as EN 160200-1 on 1994-04-15. The following date
22、s were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement(dop) 1998-06-01 latest date by which the national standards conflicting with the EN have to be withdrawn(dow)1999-06-01 Licensed Copy: sheffieldun shef
23、fieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 160200-1:1997 BSI 04-19993 Contents Page Section 1. General matters5 1.1Scope5 1.2Related documents5 1.3Units, symbols and terminology5 1.3.1Microwave modular electronic unit (MMEU)5 1.3.2Components5 1.4Standard and prefe
24、rred values6 1.4.1Preferred climatic categories6 1.4.2Preferred interfaces and fixings6 1.5Marking6 Section 2. Quality Assessment procedures7 2.1General7 2.1.1Eligibility for capability approval7 2.1.2Primary stage of manufacture7 2.1.3Sub-contracting7 2.1.4Incorporated components7 2.1.5Structurally
25、 similar units7 2.1.6Validity of release7 2.1.7Rework7 2.1.8Repair7 2.1.9Resubmission of rejected lots (for lot-by-lot inspection)7 2.2Procedure for capability approval7 2.2.1Application for capability approval7 2.2.2Granting of a capability approval7 2.2.3Description of capability (capability manua
26、l)8 2.2.4Capability qualifying components (CQCs)8 2.2.5Demonstration and verification of capability10 2.2.6Procedures to be followed in the event of CQC failure12 2.2.7Abstract of description of capability12 2.3Procedures following the granting of capability approval12 2.3.1Maintenance of capability
27、 approval12 2.3.2Procedures to be followed in the event of CQC failure12 2.3.3Modifications likely to affect the validity of the capability approval12 2.3.4Extension of capability approval12 2.4Release for delivery12 Page 2.4.1Quality conformance inspection requirements12 2.4.2Customer detail specif
28、ication12 2.4.3Detail specification for standard catalogue items to be included in the QPL13 Section 3. Test and measurement procedures14 3.1General14 3.2Standard conditions for testing14 3.2.1Standard atmospheric conditions14 3.2.2Electrical measurements14 3.3Alternative test methods15 3.4Measureme
29、nt uncertainty15 3.5Visual inspection, dimensions/gauging and mass test methods15 3.6Environmental, mechanical and endurance test methods16 3.7Electrical and performance test methods16 Annex A21 A.1Generic process flow chart Process21 A.2Process flow chart Waveguide technology22 A.3Process flow char
30、t Ferrite technology23 A.4Process flow chart Substrate line and component technology24 A.5Process flow chart Diode/transistor and complex circuit technology25 Annex B Capability approval test report26 Annex C Abstract of capability26 Annex D Requirements for the form and content of a capability manu
31、al27 Annex E27 E.1 Example of CQC selection matrix single technology27 E.2Example of CQC selection matrix multiple technologies28 Table 1 Test schedule for demonstration of limits of capability approval16 Table 2 Test schedule for demonstration of process control and maintenance of capability approv
32、al18 Table 3 Supplementary process controls20 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 160200-1:1997 BSI 04-19995 Se
33、ction 1. General matters 1.1 Scope This CECC Sectional Specification, in conjunction with the Generic Specification EN 160000 describes, a system for capability approval of manufacturers of Microwave Modular Electronic Units (MMEUs) which are not covered by other CECC specifications. It defines stan
34、dard terms, inspection procedures and methods of test for capability approval of MMEUs. These units may be supplied to either a Customers Detail Specification (CDS) or as Standard Catalogue Items. Examples of typical MMEUs which are covered by this specification and related Blank Detail Specificatio
35、ns (BDSs) are: amplifiers; couplers/power dividers; isolators/circulators; mixers; oscillators; switches; attenuators; filters; limiters; noise sources; phase shifters; transmitters (e.g. Integrated Multichannel). The MMEUs may incorporate passive and/or active devices/elements. 1.2 Related document
36、s See clause 1.2 of EN 160000. Latest issue of the following documents applies unless otherwise stated: ISO 31, Specification for quantities, units and symbols. IEC 50 (726), International electrotechnical vocabulary Transmission lines and waveguide. IEC 68, Environmental testing. IEC 154, Flanges f
37、or waveguides. IEC 410, Sampling plans and procedures for inspection by attributes. IEC 512, Electromechanical components for electronic equipment: basic testing procedures and measuring methods. CECC 00007, Sampling plans and procedures for inspection by attributes. CECC 00009, Basic testing proced
38、ures and measuring methods for electromechanical components. CECC 00200, Qualified products list. CECC 00016, Requirement for the use of statistical process control (SPC) in the CECC system. CECC 00017, Basic specification: Microwave common modules for use up to 20 GHz Interfaces, fixings, connectio
39、n protocol and module coding. CECC 00114-III, Rule of procedure 14; Quality assessment procedures; Capability approval of an electronic component manufacturing activity. CECC 00400, Handbook for the production of CECC documents. CECC 22000, Radio frequency coaxial connectors. CECC 63000, Film and hy
40、brid integrated circuits. EN 100015, Protection of electrostatic sensitive devices; Part 1: Minimum requirements. EN 160200-2, Sectional specification: Microwave modular electronic units of assessed quality Part 2: Index of test methods. 1.3 Units, symbols and terminology Unless otherwise stated the
41、y shall be as defined within ISO 31, IEC 50(726) and clause 1.3 of EN 160000. The following terminology is applicable to this specification: 1.3.1 Microwave modular electronic unit (MMEU) For the purpose of this specification the term MMEU relates to devices designed to work within the frequency ban
42、d 300 MHz 300 GHz. The definition for Modular Electronic Unit (MEU) is contained in clause 1.3 of EN 160000. MMEUs may consist of passive and/or active elements which are interconnected to form an electronic circuit. 1.3.2 Components For the purpose of this specification, in addition to conventional
43、 discrete electronic components (e.g. resistors, capacitors and semiconductor devices), the following items which utilise microwave transmission theory in their design are considered to be components: lumped elements (passive circuits based on microstrip/stripline); machined, cast and electroformed
44、items (e.g. passive filter); moulded/metallized and microwave absorbent materials (e.g. loads). Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 160200-1:1997 6 BSI 04-1999 1.4 Standard and preferred values 1.4.1 Preferred climatic categor
45、ies The MMEUs covered by this specification are classified into climatic categories according to the general rules given under IEC 68-1. The severities for cold, dry heat and damp heat steady state tests shall preferably be chosen from the following: 1.4.2 Preferred interfaces and fixings See clause
46、 1.2, the following specifications are applicable. CECC 00 017 CECC 22 000 IEC 154 1.5 Marking The MMEU and package shall be marked in accordance with clause 1.4 of EN 160000 and the BDS including necessary warning labels (e.g. electrostatic sensitive devices: EN 100015), unless otherwise specified
47、in the Customer Detail Specification. lower category temperature: 55 C, 40 C and 25 C; upper category temperature: + 85 C, + 100 C and + 125 C; duration of damp heat steady state test: (hermetically sealed units) 4, 10, 21 and 56 days Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 17 08:20:24 G
48、MT+00:00 2006, Uncontrolled Copy, (c) BSI EN 160200-1:1997 BSI 04-19997 Section 2. Quality assessment procedures 2.1 General 2.1.1 Eligibility for capability approval See clause 2.1 of CECC 00114/III. 2.1.2 Primary stage of manufacture The primary stage of manufacture is the joining together of all
49、piece parts (e.g. components, substrates and packages). This includes mounting of the piece parts to form the MMEU and necessary interconnections/terminations. The sub-contracting of the above process and/or all subsequent processes is prohibited unless otherwise stated in clause 2.1.3 of this specification. 2.1.3 Sub-contracting Sub-contracting shall be in accordance with clause 2.2 of CECC 00114/III:1989 and the constraints of clause 2.1.2 above. Only sub-contracting of the following