《BS-EN-13571-2002.pdf》由会员分享，可在线阅读，更多相关《BS-EN-13571-2002.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13571:2002 Incorporating Corrigendum No. 1 Footwear Test methods for uppers, lining and insocks Tear strength The European Standard EN 13571:2001 has the status of a British Standard ICS 61.060 ? Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, U
2、ncontrolled Copy, (c) BSI BS EN 13571:2002 This British Standard, having been prepared under the direction of the Materials and Chemicals Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 25 January 2002 BSI 12 May 2004 ISBN 0 5
3、80 38931 6 National foreword This British Standard is the official English language version of EN 13571:2001, including Corrigendum December 2003. The UK participation in its preparation was entrusted to Technical Committee TCI/69, Footwear and leather, which has the responsibility to: A list of org
4、anizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Corre
5、spondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not
6、of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulga
7、te them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 9 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateCommen
8、ts 15117 Corrigendum No. 1 12 May 2004Change to Figure 4 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13571 November 2001 ICS 61.060Incorporating Corrigendum December 2003 English versi
9、on Footwear Test methods for uppers, lining and insocks Tear strength Chaussure Mthodes dessai relatives aux tiges, doublures et premires de propret Rsistance la dchirure Schuhe Prfverfahren fr Schfte, Futter und Decksohlen Reifestigkeit This European Standard was approved by CEN on 4 October 2001.
10、CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on a
11、pplication to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has t
12、he same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Commi
13、ttee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13571:2001 E Licensed Copy: sheffield
14、un sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 2 Contents page Foreword3 1 Scope 4 2 Normative references4 3 Terms and definitions .4 4 Apparatus and material.4 5 Sampling and conditioning.5 6 Test method6 6.1 Principle6 6.2 Procedure .6 7 Expres
15、sion of results 8 8 Test report9 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 3 Foreword This European Standard has been prepared by Technical Committee CEN/TC 309 “Footwear“, the secretariat of which is held by AENOR. T
16、his European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2002, and conflicting national standards shall be withdrawn at the latest by May 2002. This European Standard is based on the IULTCS/IUP 8 method
17、 (ISO 3377:1975 “Leather - Determination of tearing load“). According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, I
18、celand, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 4 1 Scope This European Standard specifies a test method
19、for assessing the tear strength of upper, linings and insocks or complete upper assembly, irrespective of material, in order to assess the suitability for the end use. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These
20、normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated
21、 references the latest edition of the publication referred to applies (including amendments). EN 12222, Footwear - Standard atmospheres for conditioning and testing of footwear and components for footwear. EN 13400, Footwear - Sampling location, preparation and duration of conditioning of samples an
22、d test pieces. EN ISO 7500-1, Metallic materials - Verification of static uniaxial testing machines - Part 1: Tension/compression testing machines (ISO 7500-1:1999). 3 Terms and definitions For the purposes of this European Standard, the following terms and definitions apply. 3.1 tear strength media
23、n force required to propagate a cut in a specified test specimen 3.2 upper materials forming the outer face of the footwear which is attached to the sole assembly and covers the upper dorsal surface of the foot. In the case of boots this also includes the outer face of the material covering the leg.
24、 Only the materials that are visible are included, no account should be taken of underlying materials 3.3 complete upper assembly finished upper, fully seamed, joined or laminated together as appropriate, comprising the centre material and any lining(s) together with all components such as interlini
25、ngs, adhesives, membranes, foams or reinforcements, but excluding toe puffs and stiffeners NOTE The complete upper assembly can be flat, 2- dimensional or comprise lasted upper in the final footwear. 4 Apparatus and material The following apparatus and material shall be used: 4.1 Tensile testing mac
26、hine with a jaw separation rate of 100 mm/min 10 mm/min, a force range appropriate to the specimen under test (range of 0 N to 500 N is usually suitable for specimens of footwear upper materials). 4.2 Means of continuously recording the force to an accuracy greater than 2 % as specified by class 2 i
27、n EN ISO 7500-1. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 5 4.3 A press knife, or other cutting device, capable of cutting a test specimen of the dimensions shown in Figure 1, for non-leather sheet materials and Figu
28、re 2 for cutting samples from shoe uppers or leathers. 5 Sampling and conditioning 5.1 Test specimens can be cut from materials likely to be used for uppers or insocks or from made-up uppers or finished footwear. Prepare test pieces from complete upper assemblies when the lining material is permanen
29、tly attached to the upper material. 5.2 Cut six test specimens from either the sheet material or shoe upper. If testing fabric shoe uppers, the test specimen dimensions shown in Figure 2 are to be considered minimum dimensions and a larger test specimen should be cut where possible to prevent yarn s
30、lippage. 5.3 For sheet materials cut test specimens from a range of positions across the full usable width and length of the sheet material. For a material with a woven structure this will prevent any two specimens containing the same warp or weft threads. Key 1 Slit Figure 1 Test specimen for non-l
31、eather sheet materials Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 6 Key 1 25 mm or more 2 30 mm 2 mm 3 Slit Figure 2 Test specimen for leather and shoe uppers 5.4 Cut three test specimens with the slit parallel to the
32、along direction of the material (backbone direction for leather and selvedge (warp) or machine direction for non-leather materials) and three with the slit perpendicular to this. In the case of woven fabrics, use the warp directions as the along direction and the weft direction as the across even if
33、 these are not at 90 to each other. For shoe uppers, the along direction is the X-axis as defined in EN 13400. 5.5 For shoe uppers, cut six test specimens through the full thickness of the upper taking care not to dislodge any lining or interlining which has been laminated to the outer material. Tak
34、e similar care not to dislodge any lining material throughout the testing procedure. Cut three with the slit parallel to the along direction (X-axis) and three with the slit perpendicular to this. 5.6 Mark the along direction on all the test specimens. 5.7 Test specimens shall be conditioned in a st
35、andard atmosphere as specified in EN 12222 for 24 h prior to test. 6 Test method 6.1 Principle A test specimen, which has a single slit to produce two legs, is loaded into a tensile testing machine so that the slit is parallel to the axis of the machine and one leg is clamped in each jaw. The jaws a
36、re moved apart to tear the material until the tear has propagated to an edge of the test specimen. The initial force required to initiate tear, the median force required to continue the tear, the maximum force required to continue the tear and the type of tear are recorded. 6.2 Procedure 6.2.1 All t
37、ests shall be conducted in a conditioned atmosphere as specified in EN 12222. Where this is not possible, tests shall be carried out within 15 min of removing the samples from the conditioned atmosphere. 6.2.2 Zero the tensile tester force measuring system and move the jaws together to enable the te
38、st specimen to be fitted. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 7 6.2.3 Hold the test specimen flat between the jaws of the tensile testing machine so that the slit is aligned and parallel with the axis of the mac
39、hine. 6.2.4 Clamp one of the legs in the lower jaw and then fold the other leg upwards through 180 and clamp it into the upper jaw (see Figure 3). In each case ensure that the end of the leg is parallel with the clamping edge of the jaw and that the slit is positioned in the axis of the tensile test
40、er. Figure 3 Method of fixing test specimens in grips 6.2.5 Operate the tensile testing machine so that the jaws separate at a speed of 100 mm/min 10 mm/min and note the type of tear that occurs as: Normal failure: Clean tear in approximate direction of the slit Abnormal failures: - Separate tearing
41、 of coating and base fabric - Fabric yarns pulling out instead of tearing - Tearing to the side of the test specimen 6.2.6 Stop the test when the tear has propagated to an edge of the test specimen. 6.2.7 From the trace of force versus extension produced by the tensile testing machine: 6.2.7.1 If th
42、ere is a peak corresponding with the initiation of tearing, record this force value as Initial peak force to the nearest 1 N. 6.2.7.2 Record the maximum force applied to continue the tear once it had started as Maximum tear force to the nearest 1 N. 6.2.7.3 Record the average force (see Figure 4) re
43、quired to continue the tear as Median force to the nearest 1 N. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (E) 8 Key 1 Tearing force, in N 2 Average 3 Deformation Figure 4 Example of diagram force/deformation 6.2.8 Repeat
44、the procedure in 6.2.2 to 6.2.7 for the remaining test specimens. If one test specimen in either test direction shows an abnormal failure, see 6.2.5, and sufficient material is available, repeat the test until one more specimen shows a normal failure and discard the results for the abnormal failures
45、. If two or more specimens in either test direction show an abnormal type of failure, stop the test when all the original six specimens have been tested and include the results for the abnormal types of failure. 7 Expression of results For each test direction (along and across) and type of failure c
46、alculate the arithmetic mean of: a) the Initial peak forces if recorded in 6.2.7.1; b) the Maximum tear forces estimated in 6.2.7.2; c) the Median forces as recorded in 6.2.7.3. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13571:2001 (
47、E) 9 8 Test report The test report shall include the following information: a) the arithmetic mean forces determined in clause 7 together with the type(s) of failure; b) if testing finished footwear or uppers, a description of the style of shoe tested including commercial style codes; c) a descripti
48、on of any lining or other reinforcement present; d) a description of the material, including commercial reference if known; e) the number of test specimens if other than six; f) reference to the method of test; g) date of testing; h) any deviations from this test method. Licensed Copy: sheffieldun s
49、heffieldun, na, Sun Oct 29 15:41:23 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13571:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards