《BS-EN-15015-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-15015-2007.pdf（34页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15015:2007 Plastics piping systems Systems for hot and cold water not intended for human consumption Performance characteristics for pipes, fittings and their joints ICS 23.040.01 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled C
2、opy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 15015:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008 ISBN 97
3、8 0 580 54581 8 National foreword This British Standard is the UK implementation of EN 15015:2007. The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/2, Plastic piping for pressure applications. A list of organizations
4、 represented on this committee can be obtained on request to its secretary. This British Standard is intended as a means of demonstrating compliance with the Construction Products Directive (89/106/EEC) and affixing the CE mark. The Essential Requirements contained in this British Standard are conce
5、pts related to the Construction Products Directive and they are not necessarily indicative of all the performance requirements or suitability for the service conditions likely to be encountered in a particular pipework application. The CE mark indicates only that a product may legally be placed on t
6、he market in the EU. It does not indicate or guarantee inherent quality of the CE marked pipework components. It should be noted that manufacturers are entitled to declare “No Performance Determined” against some or all of these Essential Requirements and yet still affix the CE mark to their product
7、s. Users are advised to check the background details with the manufacturers claims for the CE marked products. Such details may be available on an appropriate Internet website or accompanying Company documentation. Compliance with this British Standard does not necessarily mean that products bearing
8、 the CE mark are fit for non potable hot water pipes. In addition to the above; i) The normal maximum operating cold water supply pressure in the UK is 12.5 bar which some categories of pipe in the standards listed in Annex B (excluding BS 7291-1) do not meet. ii) This standard does not specifically
9、 describe push fit joints which are the predominant jointing method in the UK. iii) There is a disparity between the malfunction temperature (100 C) quoted in the Tables of Service conditions of the standards listed in Annex B (excluding BS 7291-1) and the malfunction temperatures applicable to boil
10、ers (110 C) conforming to BS EN 297:1994, BS EN 483:2000 and BS EN 625:1996. Consequently pipe systems not conforming to BS 7291-1 could be subjected to temperatures in service for which they have not been tested. iv) The unique and traditional practice in the UK is to use products certified to BS 7
11、291 Class S for all applications, as defined in BS 7291-1. This is recognized in the National Annex to BS EN 12828 which requires the use of systems suitable for the maximum temperatures and pressures for their intended application specified in BS 7291-1. Amendments/corrigenda issued since publicati
12、on DateComments Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 15015:2007 BSI 2008 i Measures have bee
13、n taken to address these issues in this Harmonized European Standard, see clauses 4.2.1 and 5.4. This Standard does not replace BS 7291 pts 1, 2 the Water Supply (Water Quality) Regulations 2001, Regulation 27 (Scotland); and the Water Supply (Water Quality) Regulations 2007, Regulation 30 (Northern
14、 Ireland); and for installations for consumers premises: the Water Supply (Water Fittings) Regulations 1999 (England and Wales), the Water Byelaws 2000 (Scotland) and the current requirements for Northern Ireland. This publication does not purport to include all the necessary provisions of a contrac
15、t. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45
16、 MDTNo reproduction or networking permitted without license from IHS -,-,- blank Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without lic
17、ense from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15015 October 2007 ICS 23.040.01 English Version Plastics piping systems - Systems for hot and cold water not intended for human consumption - Performance characteristics for pipes, fittings and their joints Systmes de canalisa
18、tions en plastique - Systmes pour eau chaude et froide non destine la consommation humaine - Caractristiques de performance pour tubes, raccords et leurs assemblages Kunststoff-Rohrleitungssysteme - Rohrleitungssysteme fr Warm- und Kaltwasser nicht fr den menschlichen Gebrauch - Eigenschaften fr die
19、 Gebrauchstauglichkeit von Rohren, Formstcken und deren Verbindungen This European Standard was approved by CEN on 23 August 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national stand
20、ard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other
21、language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, F
22、inland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHE
23、S KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15015:2007: E Copyright British Standards Institution Provided by IHS under license with BSI - Uncontro
24、lled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15015:2007 (E) 2 Contents page Foreword3 Introduction.4 1 Scope5 2 Normative references .5 3 Terms, definitions and symbols6 4 Performance requirem
25、ents 6 4.1 Reaction to fire.6 4.2 Internal pressure strength and resistance to high temperature.6 4.3 Dimensional tolerances.6 4.4 Tightness7 4.5 Durability.7 4.6 Dangerous substances .7 5 Test methods.7 5.1 Reaction to fire.7 5.2 Determination of the design pressure.8 5.3 Dimensional tolerances.8 5
26、.4 Tightness and durability .8 6 Evaluation of conformity9 6.1 General9 6.2 Initial type testing.10 6.3 Factory production control.11 6.4 One-off products and products produced in very low quantities.14 Annex A (normative) Overall service (design) coefficients.15 A.1 General15 A.2 Overall service (d
27、esign) coefficients .15 Annex B (normative) Product standards for hot and cold water installations inside buildings.16 Annex C (normative) Standards for assessment of conformity for hot and cold water installations inside buildings18 Annex ZA (informative) Clauses of this European Standard addressin
28、g the provisions of the EU Construction Products Directive (CPD)19 ZA.1 Scope and relevant characteristics .19 ZA.2 Procedure for attestation of conformity of plastics pipes and fittings20 ZA.3 CE marking and labelling24 Bibliography28 Copyright British Standards Institution Provided by IHS under li
29、cense with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15015:2007 (E) 3 Foreword This document (EN 15015:2007) has been prepared by Technical Committee CEN/TC 155 “Plastics pipi
30、ng systems and ducting systems“, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn at the l
31、atest by July 2009. This document has been prepared under the mandate M/131 “Pipes, tanks and ancillaries not in contact with water intended for human consumption” given to CEN by the European Commission and the European Free Trade Association and support essential requirements of EU Directives. For
32、 the relationship with EU Directives, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cy
33、prus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Copyright British Standards Institution
34、 Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15015:2007 (E) 4 Introduction This European Standard contains only the performance characteristic
35、s needed to meet the essential requirements of EU Directive(s). It does not cover all characteristics of the products. These are specified in the standards listed in Annex A or in other appropriate product specifications. This harmonised European Standard is part of a family of cluster standards add
36、ressing plastics piping systems. The relationship is shown below. Material independent Specific solutions For the harmonisation of plastics piping systems for hot and cold water (this European Standard) the following applies: For pipes and fittings For valves Figure 1 Copyright British Standards Ins
37、titution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:45 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15015:2007 (E) 5 1 Scope This European Standard specifies performance requirements for pl
38、astics pipes, fittings and their joints intended for hot and cold water installations for the conveyance of water and for heating systems with the exception of drinking water distribution for human consumption, and gives associated test methods for verification and evaluation of conformity with this
39、 European Standard. NOTE Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged E
40、uropean Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of this standard, products conforming to this standard could be used for the transport of water intended for human consumption if they conform to the relevant national, regional
41、or local regulatory provisions or recommendations applicable in the place of use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the
42、referenced document (including any amendments) applies. EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applica
43、tions Part 2: Thermoplastic elastomers EN 12293, Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted assemblies to temperature cycling EN 13501-1, Fire classification of construction products and building elements Part 1: Classif
44、ication using test data from reaction to fire tests EN 15012:2007, Plastics piping systems Soil and waste discharge systems within the building structure Performance characteristics for pipes, fittings and their joints EN ISO 1167-1, Thermoplastics pipes, fittings and assemblies for the conveyance o
45、f fluids Determination of the resistance to internal pressure Part 1: General method (ISO 1167-1:2006) EN ISO 1167-2, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 2: Preparation of pipe test pieces (ISO 1167-2:20
46、06) prEN ISO 1167-3, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 3: Preparation of components (ISO/DIS 1167-3:2005) prEN ISO 1167-4, Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Det
47、ermination of the resistance to internal pressure Part 4: Preparation of assemblies (ISO/DIS 1167-4:2006) EN ISO 3126, Plastics piping systems Plastics components Determination of dimensions (ISO 3126:2005) EN ISO 9001:2000, Quality management systems Requirements (ISO 9001:2000) EN ISO 9080, Plasti
48、cs piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation (ISO 9080:2003) ISO 10508:2006, Plastics piping systems for hot and cold water installations Guidance for classification and design Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/