《BS-EN-13394-2001.pdf》由会员分享，可在线阅读，更多相关《BS-EN-13394-2001.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13394:2001 Packaging Specification for non-metallic tensional strapping The European Standard EN 13394:2001 has the status of a British Standard ICS 55.040 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BS EN 13394:2001 This British Standard, having bee
2、n prepared under the direction of the Consumer Products and Services Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 June 2001 BSI 06-2001 ISBN 0 580 37100 X National foreword This British Standard is the official English language version of
3、 EN 13394:2001. It supersedes BS 6975:1988 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee PKW/5, Primary and transport packaging, to Subcommittee PKW/5/33, Tensional strapping, taping and accessories, which has the responsibility to: A list of organi
4、zations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Stand
5、ards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standa
6、rd does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments
7、and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 11 and a back cover. The BSI copyright date displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No.
8、 DateComments EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13394 April 2001 ICS 55.040 English version Packaging Specification for non-metallic tensional strapping Conditionnement Caractristiques des feuillards de cerclage non mtalliques Verpackung Spezifikation fr nichtmetallische Umreifung
9、sbnder This European Standard was approved by CEN on 18 January 2001. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographi
10、cal references concerning such national standards may be obtained on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN me
11、mber into its own language and notified to the Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portu
12、gal, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2001 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN n
13、ational Members. Ref. No. EN 13394:2001 E Page 2 EN 13394:2001 BSI 06-2001 Contents Page Foreword. 3 1Scope . 4 2Normative references . 4 3Classification of materials . 4 4General. 5 5Dimensions and physical properties 5 6Mechanical and physical testing. 8 Annex A (informative) Preferred colours . 1
14、1 Page 3 EN 13394:2001 BSI 06-2001 Foreword This European Standard has been prepared by Technical Committee CEN/TC 261, Packaging, the Secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endo
15、rsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latest by October 2001. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belg
16、ium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Page 4 EN 13394:2001 BSI 06-2001 1 Scope This European Standard specifies dimensions and physical properties for non-
17、metallic strapping used to secure, to close, to unitize or to strengthen packages applied by hand tools or automatic machines. NOTEFor particular applications or specific requirements, other dimensions can be supplied by agreement between customer and supplier. 2 Normative references The following n
18、ormative documents contain provisions which, through reference in this text, constitute provisions of this European Standard. For dated references, subsequent amendments to, or revisions of, this publication, do not apply. However, parties to agreements based on this European Standard are encouraged
19、 to investigate the possibility of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the publication referred to applies (including amendments). EN ISO 1421, Rubber or plastics-coated fabrics Determination of tensile strength an
20、d elongation at break (ISO 1421:1998). EN ISO 2233:1999, Packaging Complete, filled transport packages Conditioning for testing (ISO 2233:1994). 3 Classification of materials 3.1 Thermoplastics strapping Strapping produced by extrusion, generally of rectangular cross-section, in which high tensile s
21、trength has been developed by orientation. 3.1.1 Polyamide strapping Extruded and oriented polyamide (PA) . 3.1.2 Polypropylene strapping Extruded and oriented polypropylene (PP). 3.1.3 Polyester strapping Extruded and oriented polyester (Polyethylene-terephthalate) (PET). 3.2 Textile strapping Stra
22、pping produced from continuous longitudinal strands of textile material. 3.2.1 Polyester textile strapping Strapping that consists of continuous longitudinal strands of high tensile polyester fibres bonded together with a suitable adhesive or polymer coating forming a non-woven product, or in combin
23、ation with a weft forming a woven product. Page 5 EN 13394:2001 BSI 06-2001 4 General 4.1 Surface finish Polyamide strapping is flat. Polypropylene and polyester strapping may be either flat or embossed. 4.2 Colour Non-metallic strapping may be supplied in various colours for identification. NOTESee
24、 Annex A (informative) for preferred colours. 4.3 Recycling Non-metallic strapping may be recovered, separated and recycled. The calorific energy of thermoplastic non-metallic strapping may be recovered by incineration. 5 Dimensions and physical properties 5.1 Polyamide Dimensions and physical prope
25、rties for polyamide strapping shall be as in Table 1. Table 1 Polyamide Dimensions and physical properties Nominal width mm Minimum width mm Maximum width mm Minimum break strength N Range of Elongation at break % Nominal Thickness Range mm 1110,9511,351 870, 2 490, 3 11010 to 200,4 to 0,8 12,712,55
26、12,951 870, 2 490, 3 110, 4 00010 to 200,25 to 0,8 Page 6 EN 13394:2001 BSI 06-2001 5.2 Polypropylene Dimensions and physical properties for polypropylene strapping shall be as in Table 2. Table 2 Polypropylene Dimensions and physical properties Nominal width mm Minimum width mm Maximum width mm Min
27、imum break strength N 54,65,1350, 450, 550, 700 5,55,15,6500, 650, 800 65,66,1400, 600, 800 76,57,1700, 850 87,58,1600, 700, 900, 1 100, 1 300 98,59,1700, 850, 1 000, 1 200, 1 400, 1 600, 1 800 109,510,11 000, 1 250, 1 500, 1 800 1110,511,11 100, 1 300, 1 600, 2 000, 2 200, 2 500, 2 800 1211,312,11
28、100, 1 300, 1 500, 1 600, 1 800, 1 900, 2 200, 2 500, 2 800, 3 000 12,712,012,81 500, 1 750, 2 000, 2 400, 2 700, 2 800, 3 000, 3 300, 3 500, 3 800 1514,315,11 700, 2 000, 2 500, 3 000, 3 500, 4 000, 5 000 1615,316,11 700, 1 900, 2 200, 2 500, 2 700, 3 000, 3 500, 4 000, 5 000 1918,319,11 600, 3 500
29、, 4 200, 6 000 For hand tool applications the width tolerance shall be 6 % of the nominal width Page 7 EN 13394:2001 BSI 06-2001 5.3 Polyester Dimensions and physical properties for polyester strapping shall be as in Table 3. Table 3 Polyester Dimensions and physical properties Nominal width mm Mini
30、mum width mm Maximum width mm Minimum break strength N 9,59,09,61 800, 2 000, 2 200, 2 500 109,510,12 300, 3 200 1110,511,12 100, 2 500, 2 700, 3 200 1211,312,12 100, 2 300, 2 600, 2 900, 3 200, 3 500, 4 500 12,712,012,82 100, 2 600, 2 900, 3 300, 3 800 1514,315,14 300, 5 600, 6 300, 7 100 1615,316,
31、12 900, 3 800, 4 800, 5 300, 5 700, 6 500 1918,319,17 000, 9 000, 10 000 5.4 Mechanical properties 5.4.1 Polypropylene Mechanical properties for polypropylene strapping shall be as in Table 4. Table 4 Polypropylene Mechanical properties Minimum tensile strength MPa Elongation % Type 33012 to 20I 300
32、15 to 25II 5.5 Polyester Mechanical properties for polyester strapping shall be as in Table 5. Table 5 Polyester Mechanical properties Minimum tensile strength MPa Elongation % Type 5108 to 15I 46012 to 18II 39014 to 20III Page 8 EN 13394:2001 BSI 06-2001 5.6 Polyamide Mechanical properties for poly
33、amide strapping shall be as in Table 6. Table 6 Polyamide Mechanical properties Minimum tensile strength MPa Elongation % 38012 6 Mechanical and physical testing 6.1 Conditioning Conditioning shall be as section 4, condition 7 of EN ISO 2233:1999. 6.2 Determination of break strength and elongation a
34、t break Mechanical tests shall be conducted according to the strip test method of EN ISO 1421 except that a cut length of material in its original condition, width and thickness shall be used as the test-piece. Further conditioning for testing is not necessary. The gauge length for measurement of el
35、ongation at break shall be 100 mm. 6.3 Camber 6.3.1 Automatic applications For automatic applications see Figure 1. 6.3.2 For strapping widths up to 6 mm The maximum camber shall be less than 240 mm per 2 000 mm. 6.3.3 For strapping widths from 7 mm to 11 mm The maximum camber shall be less than 150
36、 mm per 2 000 mm. 6.3.4 For strapping widths greater than 12 mm The maximum camber shall be less than 120 mm per 2 000 mm. Page 9 EN 13394:2001 BSI 06-2001 Key 1Camber Figure 1 Camber 6.4 Production Welds Maximum of two production welds per coil allowed. 6.5 Coil Sizes Standard coil core dimensions
37、are as shown in Table 7. Page 10 EN 13394:2001 BSI 06-2001 Table 7 Coil core dimensions Nominal coil inner diameter mm Nominal coil width mm 62160 70160 76140 76175 102146 150156 200190 280190 40676 406150 406190 610150 Page 11 EN 13394:2001 BSI 06-2001 Annex A (informative) Preferred colours Prefer
38、red colours Preferred colours for non-metallic tensional strapping are shown in Table A.1. Table A.1 Preferred colours for non-metallic tensional strapping AbbreviationMaterialColour PAPolyamideBlue PPPolypropyleneBlack PETPolyesterGreen TextilePolyesterWhite BS EN 13394:2001 BSI 389 Chiswick High R
39、oad London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendme
40、nt or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard woul
41、d inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions
42、of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards
43、, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Ex
44、porters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substant
45、ial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications.
46、BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopyi
47、ng, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.