《BS-EN-2157-1-1993.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2157-1-1993.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2157-1:1993 Steel Forging stock and forgings Technical specifications Part 1: General requirements The European Standard EN 2157-1:1993 has the status of a British Standard Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:17:56 GMT+00:00 2006, Uncontr
2、olled Copy, (c) BSI BS EN 2157-1:1993 This British Standard, having been prepared under the direction of the Aerospace Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 December 1993 BSI 07-1999 The following BSI references relate to the
3、 work on this standard: Committee reference ACE/61 Draft for comment 90/80845 DC ISBN 0 580 22105 9 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following
4、 countries: AustriaOesterreichisches Normungsinstitut BelgiumInstitut belge de normalisation DenmarkDansk Standardiseringsraad FinlandSuomen Standardisoimisliito, r.y. FranceAssociation franaise de normalisation GermanyDeutsches Institut fr Normung e.V. GreeceHellenic Organization for Standardizatio
5、n IcelandTechnological Institute of Iceland IrelandNational Standards Authority of Ireland ItalyEnte Nazionale Italiano di Unificazione LuxembourgInspection du Travail et des Mines NetherlandsNederlands Normalisatie-instituut NorwayNorges Standardiseringsforbund PortugalInstituto Portugus da Qualida
6、de SpainAsociacin Espaola de Normalizacin y Certificacin SwedenStandardiseringskommissionen i Sverige SwitzerlandAssociation suisse de normalisation United KingdomBritish Standards Institution Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Fri No
7、v 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2157-1:1993 BSI 07-1999i Contents Page Cooperating organizationsInside front cover National forewordii Foreword2 Text of EN 2157-13 National annex NA (informative) Committees responsibleInside back cover National annex NB (informative) C
8、ross-referencesInside back cover Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2157-1:1993 ii BSI 07-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and i
9、s the English language version of EN 2157-1:1993, Aerospace Series Steel. Forging stock and forgings. Technical specifications. Part 1 General requirements, published by the European Committee for Standardization (CEN). EN 2157-1 was produced as a result of international discussion in which the Unit
10、ed Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary o
11、f pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on
12、 the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2157-1 August 1993 UDC 669.14-4:621:73:620.1:62-777:629.7 Descriptors: Aircraft industry, forgings, die forgings, s
13、teels, specifications, generalities English version Aerospace series Steel Forging stock and forgings Technical specifications Part 1 General requirements Srie arospatiale Acier Produits destins la forge Pices forges et pices matrices Spcification technique Partie 1 Exigences gnrales Luft- und Raumf
14、ahrt Stahl Schmiedevormaterial und Schmiedestcke Technische Lieferbedingungen Teil 1 Allgemeine Anforderungen This European Standard was approved by CEN on 1993-08-19. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St
15、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Frenc
16、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, Fr
17、ance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels
18、1993 Copyright reserved to CEN members Ref. No. EN 2157-1:1993 E Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2157-1:1993 BSI 07-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufact
19、urers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This standard was sub
20、mitted for Formal Vote, and the result was positive. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 1994, and conflicting national standards shall be withdrawn at the latest by February
21、1994. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingd
22、om. Contents Page Foreword 2 1Scope3 2Normative references3 3Definitions3 4Quality assurance4 5Manufacture4 6Traceability4 7Freedom from defects4 8Testing4 9Marking5 10Acceptance5 11Inspection and test report5 12Packing6 13Wording of orders6 Table 14 Licensed Copy: sheffieldun sheffieldun, na, Fri N
23、ov 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2157-1:1993 BSI 07-19993 1 Scope This standard defines the general requirements for the manufacture, inspection and testing of forging stock, hand forgings1) including forged blocks and rings1), die forgings and rolled rings1) in steel. Th
24、e specific requirements are defined in EN 2157-2 and EN 2157-3. The three standards EN 2157-1, EN 2157-2 and EN 2157-3 define the inspection level and the sampling frequency to be applied unless otherwise specified on the drawing, order or inspection schedule. For aerospace purposes this standard sh
25、all be applied in conjunction with EN material standards unless otherwise specified on the drawing, order or inspection schedule. By agreement between the manufacturer and the purchaser, this standard can also be applied to other materials and conditions of supply not covered by EN material standard
26、s. This agreement shall be formalized by reference to this standard on the drawing, order or inspection schedule. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate plac
27、es in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication refer
28、red to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2078, Aerospace series Metallic materials Manufacturing schedule Inspection schedule Inspection and test report Description and rules for use. EN 2157-2, Aerospace se
29、ries Steel Forging stock and forgings Technical specification Part 2 Forging stock. EN 2157-3, Aerospace series Steel Forging stock and forgings Technical specification Part 3 Pre-production and production forgings. 3 Definitions 3.1 purchaser body which purchases the products from a manufacturer or
30、 a stockist in accordance with the requirements of the user NOTEThe purchaser may also be the user. 3.2 user see EN 2000 3.3 cast metal from the same final melting operation 3.4 campaign a continuous production sequence using the same equipment without alteration to the operating conditions 3.5 batc
31、h a batch consists of forging stock or forgings: of the same form and nominal dimensions or having the same drawing or part number; from the same cast; from the same campaign; in the same heat treatment condition; from the same heat treatment charge or from the same heat treatment campaign which sha
32、ll be specified in the manufacturing schedule. 3.6 pre-production forgings forgings produced to a particular design which qualify the method of manufacture, equipment configuration and, if appropriate, the forging stock source, which demonstrate that the requirements of the purchaser can be met 3.7
33、inspection schedule see EN 2078 3.8 manufacturing schedule see EN 2078 1) Hereafter described as “forgings”. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2157-1:1993 4 BSI 07-1999 3.9 inspection and test report see EN 2078 3.10 “capabi
34、lity clause” reference to “capability clause” signifies that sufficient evidence of statistical nature with respect to the properties under consideration can be submitted to show that the requirements of the relevant standard may be met on the basis of a reduced amount of testing. Such action in no
35、way reduces the obligations of the manufacturer to fulfil all requirements. If subsequent testing indicates that a product does not comply with the requirements the batch shall be rejected 4 Quality assurance 4.1 Approval of quality system of manufacturers See EN 2000. 4.2 Product qualification See
36、material standard. 5 Manufacture 5.1 Forgings shall be made from forging stock complying with the relevant EN material standard and with EN 2157-2. 5.2 Compliance with the requirements of the purchaser shall be demonstrated by the manufacture and inspection and testing of pre-production forgings as
37、required by EN 2157-3. 5.3 Unless otherwise specified, the forging stock and forgings shall be supplied in the heat treatment condition specified in the material standard. If there is more than one heat treatment condition contained in the material standard, the delivery condition shall be specified
38、 on the order or on the drawing. If a specific temperature (value and tolerance) is stated, that temperature shall be mandatory. If a temperature range is stated, a temperature within that range reduced by the furnace tolerances shall be selected to give the required properties. Unless otherwise spe
39、cified, the charge shall be maintained at the temperature subject to the following tolerances (see Table 1), for the period stated. Table 1 6 Traceability Each product shall be identifiable to its batch at all stages of manufacture and delivery. 7 Freedom from defects All products shall be free from
40、 irregularities not complying with the requirements of the material standard or the order, or prejudicial to the subsequent manufacture or use of the product. Notwithstanding previous acceptance of products complying with this standard, any product that is found, at a later stage, to contain such de
41、fects, may be rejected. 8 Testing The tests required by the material standard or the order shall be made in accordance with the requirements of the appropriate test standard. If a test standard does not exist, the method shall be agreed between the manufacturer and the purchaser. Unless otherwise sp
42、ecified on the order, the frequency of testing shall be as specified in EN 2157-2 or EN 2157-3. Where necessary, the location and the direction of the test samples shall be specified on the order. 8.1 Chemical composition It shall comply with the requirements of the relevant material standard and sh
43、all be determined on each cast. The samples taken for analysis shall be representative of the cast. The method of analysis shall be selected by the manufacturer, but in case of dispute, the method set out in the relevant ISO standard shall be used. If no ISO standard exists, a fundamental method of
44、chemical analysis shall be used. 8.2 Preparation of the test samples and test pieces 8.2.1 Test samples for forgings for the tests required by the material standard shall be obtained by one or more of the following methods as agreed between the manufacturer and the purchaser and indicated on the dra
45、wing or the inspection schedule: a) test samples cut from forgings; b) test samples forged integrally with the forgings; c) test samples forged separately from the same batch of forging stock as the forgings they represent. Selected temperature CTolerances C 750 5 750 k F k 1250 10 Licensed Copy: sh
46、effieldun sheffieldun, na, Fri Nov 03 01:17:56 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2157-1:1993 BSI 07-19995 8.2.2 Dimensions of test samples and associated test pieces representing forgings are to be agreed between the manufacturer and the purchaser and shall be stated on the drawing or in
47、spection schedule. 8.2.3 The test samples and associated test pieces shall be marked in such a manner that their idendity and orientation with respect to the product and the batch is maintained. 8.2.4 Test samples removed from finished forgings shall not be further worked. 8.2.5 Should the test samp
48、les be cut from forgings, the purchaser shall specify in the drawing or inspection schedule the number of forgings to be cut up and the location from which the samples are to be taken. 8.3 Heat treatment of test samples 8.3.1 Test samples representing forgings to be supplied in any heat treated cond
49、ition shall be heat treated with the batch of forgings they represent. Unless otherwise agreed between the manufacturer and the purchaser, samples shall not be cut from forgings before heat treatment. 8.3.2 Test samples cut from forgings in the finally heat treated condition shall not be further heat treated. 8.3.3 Test samples representing forgings supplied in other than the finally heat treated condition, shall be additionally heat treated in accordance with the requirements of the mat