《BS-EN-2591-102-1996.pdf》由会员分享，可在线阅读，更多相关《BS-EN-2591-102-1996.pdf（10页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD AEROSPACE SERIES BS EN 2591-102:1996 Elements of electrical and optical connection Test methods Part 102: Examination of dimensions and mass The European Standard EN 2591-102:1996 has the status of a British Standard ICS 49.060 Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02
2、17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-102:1996 This British Standard, having been prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 July 1996 BSI 11-1998 First published as BS EN
3、 2591-A2 February 1994 The following BSI references relate to the work on this standard: Committee reference ACE/6 Draft for comment 92/84568 DC ISBN 0 580 25950 1 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee ACE/6, Ae
4、rospace avionic, electrical and fibre-optic technology, upon which the following bodies were represented: British Airways British Cable Makers Confederation British Rubber Manufacturers Association Civil Aviation Authority (Airworthiness Division) Federation of the Electronics Industry Ministry of D
5、efence Society of British Aerospace Companies Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-102:1996 BSI 11-1998i Contents Page Committees responsible Inside front cover N
6、ational foreword ii Foreword 2 1 Scope 3 2 Normative references 3 3 Means of measurement3 List of references Inside back cover Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-102:1996 ii BSI 11-1998 National foreword This British
7、Standard has been prepared by Technical Committee ACE/6 and is the English language version of EN 2591-102:1996 Aerospace series Elements of electrical and optical connection Test methods Part 102: Examination of dimensions and mass, published by the European Committee for Standardization (CEN). It
8、supersedes BS EN 2591-A2:1994 which is withdrawn. BS EN 2591-102:1996 was produced as a result of international discussions in which the United Kingdom took an active part. Cross-reference The British Standard corresponding to the European Standard referred to in the text is identical in number and
9、title with that given in clause 2. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summar
10、y of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table
11、 on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2591-102 February 1996 ICS 49.060Supersedes EN 2591-A2:1993 Descriptors: Aircraft industry, aircraft equipment,
12、connecting equipment, tests, verification, dimensional measurements, mass English version Aerospace series Elements of electrical and optical connection Test methods Part 102: Examination of dimensions and mass Srie arospatiale Organes de connexion lectrique et optique Mthodes dessais Partie 102: Ex
13、amen des dimensions et masses Luft- und Raumfahrt Elektrische und optische Verbindungselemente Prfverfahren Teil 102: Prfung der Mae und Masse This European Standard was approved by CEN on 1993-12-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the condi
14、tions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three
15、official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austr
16、ia, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue
17、 de Stassart 36, B-1050 Brussels 1996 Copyright reserved to CEN members Ref. No. EN 2591-102:1996 E Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2591-102:1996 2 BSI 11-1998 Foreword This European Standard has been prepared by the Europ
18、ean Association of Aerospace Manufacturers (AECMA). The alphanumerical designation of the Parts of EN 2591 has been abandoned for a numerical designation in line with the Internal Regulations of CEN/CENELEC. This European Standard is the integral reproduction of the European Standard EN 2591-A2 afte
19、r application of this decision, without any other modification than the change in numbering. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by August 1996, and conflicting national standards shall b
20、e withdrawn at the latest by August 1996. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg
21、, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 2591-102:1996 BSI 11-19983 1 Scope This standard specifies a method for checking the dimensions and mass of el
22、ements of electrical and optical connection. It shall be used together with EN 2591. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publica
23、tions are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2591, Aeros
24、pace series Elements of electrical and optical connection Test methods General. 3 Means of measurement The dimensions, mass, thickness of protection1) and surface roughness1) shall be checked by suitable measuring instruments or instruments required by the technical specification (example: gauge). I
25、n the case of moving parts, backlash shall be eliminated before the dimensions are checked in both directions. 1) If required. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:
26、58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 2591-102:1996 BSI 11-1998 List of references See national foreword. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | |
27、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body resp
28、onsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amen
29、dments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be f
30、ound on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards public
31、ations should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards B
32、SI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centr
33、e. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 700
34、1. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or trans
35、mitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details
36、 are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Thu Nov 02 17:58:24 GMT+00:00 2006, Uncontrolled Copy, (c) BSI