《BS-EN-13898-2003.pdf》由会员分享，可在线阅读，更多相关《BS-EN-13898-2003.pdf（62页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 13898:2003 Machine tools Safety Sawing machines for cold metal The European Standard EN 13898:2003 has the status of a British Standard ICS 25.080.60 ? Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 13898:2003 T
2、his British Standard was published under the authority of the Standards Policy and Strategy Committee on 1 October 2003 BSI 1 October 2003 ISBN 0 580 42733 1 National foreword This British Standard is the official English language version of EN 13898:2003. The UK participation in its preparation was
3、 entrusted to Technical Committee MTE/1, Machine tools, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in thi
4、s document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a con
5、tract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals
6、for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 58, an inside back cover and a back cover. The BSI copyr
7、ight notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM E
8、N 13898 September 2003 ICS 25.080.60 English version Machine tools - Safety - Sawing machines for cold metal Machines-outils - Scurit - Machines scier les mtaux froid Werkzeugmaschinen -Sicherheit - Sgemaschinen fr die Kaltbearbeitung von Metall This European Standard was approved by CEN on 1 August
9、 2003. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtain
10、ed on application to the Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Management Centr
11、e has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and U
12、nited Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2003 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13898:20
13、03 E Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13898:2003 (E) 2 Contentspage Foreword. 3 Introduction 3 1Scope . 3 2Normative references . 4 3Terms and definitions. 7 4List of significant hazards 8 5Safety requirements and/or protec
14、tive measures. 13 5.1General. 13 5.2Machine type-specific clauses 13 5.3Protection against common mechanical hazards. 17 5.4Typespecific safeguarding requirements additional to those defined in 5.3 . 19 5.5Other mechanical hazards. 23 5.6Electrical hazards caused by direct and indirect contact 25 5.
15、7Thermal hazards 25 5.8Hazards generated by noise 25 5.9Hazards generated by vibration 26 5.10Hazards generated by materials or substances processed. 26 5.11Hazards generated by neglect of ergonomic principles in machinery design. 28 5.12Unexpected startup unexpected overrun / over-speed 29 5.13Erro
16、rs of fitting 30 5.14Falling or ejected objects or fluids 30 5.15Loss of stability/overturning of machinery 31 5.16Slip, trip and fall of persons. 31 6Verification of safety requirements and/or measures. 31 7Information for use . 32 7.1Marking 32 7.2Instruction handbook . 32 7.3Noise declaration 33
17、Annex A (normative) Noise emission measurement 34 Annex B (normative) Recommended test conditions for measurement of noise level at sawing machines and work material specifications. 35 B.1Recommended test conditions for measurement of noise level at sawing machines 35 B.2Work material specifications
18、. 35 Annex C (informative) Examples of sawing machines types. 39 Annex D (informative) Examples of guarding solutions for sawing machines 50 Annex ZA (informative) Relationship of this document with EC Directives. 57 Bibliography. 58 Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GM
19、T+00:00 2006, Uncontrolled Copy, (c) BSI EN 13898:2003 (E) 3 Foreword This document (EN 13898:2003) has been prepared by Technical Committee CEN/TC 143 “Machine tools - Safety”, the secretariat of which is held by SNV. This European Standard shall be given the status of a national standard, either b
20、y publication of an identical text or by endorsement, at the latest by March 2004, and conflicting national standards shall be withdrawn at the latest by March 2004. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association and su
21、pports essential requirements of EC Directive(s). For relationship with EC Directives, see informative annex ZA, which is an integral part of this document. Annexes A and B are normative. Annexes C and D are informative. This document includes a Bibliography. According to the CEN/CENELEC Internal Re
22、gulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain,
23、Sweden, Switzerland and the United Kingdom. 0Introduction This standard is a type C standard (see introduction of EN 2921:1991) which applies to sawing machines. The extent to which significant hazards are covered by this standard is indicated in the scope of this standard. In addition, sawing machi
24、nes should comply, as appropriate, with EN 2921 and 2 for hazards which are not covered by this standard. Complementary requirements and guidance are given in type A and type B standards to which reference is made in the text. The figures are intended to be examples and not to give the only interpre
25、tation of the text. 1 Scope 1.1 This standard specifies the safety requirements and measures to be adopted by persons undertaking the design, construction and supply (including installation, settingup, maintenance, and repair) of machines whose primary intended use is for sawing cold metal (ferrous
26、and non-ferrous), or material partly of cold metal, by means of a saw blade. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13898:2003 (E) 4 1.2 This standard takes into account the intended use, reasonably foreseeable misuse, machine se
27、tting and blade fitting, maintenance and cleaning, and their effects on the safety of operators and other exposed persons. It presumes access to the machine from all directions at floor level and addresses both normal operation and unexpected or unintended starting. 1.3 This standard applies to the
28、ancillary devices which form an integral part of the machine. Where such devices are not an integral part of the machine, the designer, manufacturer or supplier of the installation should take into account their intended use, and should make provision for the safe linking of such devices with the ma
29、chine. 1.4 This standard applies to (metal) sawing machines which are manufactured after the date of publication by CEN of this standard. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited
30、 at the appropriate places in the text, and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition
31、 of the publication referred to applies (including amendments). EN 292-1:1991, Safety of machinery - Basic concepts, general principles for design Part 1: Basic terminology, methodology. EN 292-2:1991, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and
32、 specifications. EN 292-2/A1:1995, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and specifications, Amendment A1. EN 294:1992, Safety of machinery Safety distance to prevent danger zones being reached by the upper limbs. EN 349, Safety of machinery M
33、inimum gaps to avoid crushing of parts of the human body. EN 414, Safety of machinery Rules for the drafting and presentation of safety standards. EN 418, Safety of machinery Emergency stop equipment, functional aspects Principles for design. EN 614-1, Safety of machinery Ergonomic design principles
34、 Part 1: Terminology and general principles. EN 614-2, Safety of machinery - Ergonomic design principles - Part 2: Interactions between the design of machinery and work tasks. EN 626-1, Safety of machinery Reduction of risks to health from hazardous substances emitted by machinery Part 1: Principles
35、 and specifications for machinery manufacturers. EN 811, Safety of machinery Safety distances to prevent danger zones being reached by the lower limbs. EN 842, Safety of machinery - Visual danger signals - General requirements, design and testing. EN 894-1, Safety of machinery - Ergonomic requiremen
36、ts for the design of displays and control actuators - Part 1: General principles for human interactions with displays and control actuators. Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13898:2003 (E) 5 EN 894-2, Safety of machinery -
37、Ergonomics requirements for the design of displays and control actuators - Part 2: Displays. EN 894-3, Safety of machinery - Ergonomics requirements for the design of displays and control actuators - Part 3: Control actuators. EN 953:1997, Safety of machinery Guards General requirements for the desi
38、gn and construction of fixed and movable guards. EN 954-1, Safety of machinery Safety-related parts of control systems Part 1: General principles for design. EN 981, Safety of machinery - System of auditory and visual danger and information signals. EN 982, Safety of machinery Safety requirements fo
39、r fluid power systems and their components Hydraulics. EN 983, Safety of machinery Safety requirements for fluid power systems and their components Pneumatics. EN 999, Safety of machinery The positioning of protective equipment in respect of approach speeds of parts of the human body. EN 1005-1, Saf
40、ety of machinery Human physical performance Part1: Terms and definitions. EN 1005-2, Safety of machinery Human physical performance Part 2: Manual handling of machinery and component parts of machinery. EN 1005-3, Safety of machinery Human physical performance Part 3: Recommended force limits for ma
41、chinery operation. EN 1033, Hand-arm vibration Laboratory measurement of vibration at the grip surface of hand-guided machinery General. EN 1037:1995, Safety of machinery Prevention of unexpected start-up. EN 1050:1996, Safety of machinery Principles for risk assessment. EN 1070:1998, Safety of mach
42、inery Terminology. EN 1088:1995, Safety of machinery Interlocking devices associated with guards Principles for design and selection. EN 1299, Mechanical vibration and shock Vibration isolation of machines Information for the application of source isolation. EN 1760-1, Safety of machinery Pressure s
43、ensitive protective devices Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors. EN 1837, Safety of machinery Integral lighting of machines. EN 60204-1:1997, Safety of machinery - Electrical equipment of machines - Part 1: General requiremen
44、ts (IEC 60204-1:1997). EN 61000-6-2, Electromagnetic compatibility (EMC) Part 6-2: Generic standards; Immunity for industrial environments (IEC 61000-6-2: 1999, modified). Licensed Copy: sheffieldun sheffieldun, na, Sun Oct 29 10:04:58 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 13898:2003 (E) 6 E
45、N 61000-6-4, Electromagnetic compatibility (EMC) Part 6-4: Generic standards; Emission standard for industrial environments (IEC 61000-6-4:1997, modified). EN 61496-1:1997, Safety of machinery Electro-sensitive protective equipment Part 1: General requirements and tests (IEC 61496-1:1997). EN ISO 37
46、44, Acoustics Determination of sound power levels of noise sources using sound pressure Engineering method in an essentially free field over a reflecting plane (ISO 3744:1994). EN ISO 3746:1995, Acoustics Determination of sound power levels of noise sources using sound pressure Survey method using a
47、n enveloping measurement surface over a reflecting plane (ISO 3746:1995). EN ISO 4871, Acoustics Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996). EN ISO 7250, Basic human body measurements for technological design (ISO 7250:1996). EN ISO 9614-1, Acous
48、tics Determination of sound power levels of noise sources using sound intensity Part 1: Measurement at discrete points (ISO 9614-1:1993). EN ISO 11202:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified p
49、ositions - Survey method in situ (ISO 11202:1995). EN ISO 11204:1995, Acoustics - Noise emitted by machinery and equipment - Measurement of emission sound pressure levels at a work station and at other specified positions - Method requiring environmental corrections (ISO 11204:1995). EN ISO 11546-1, Acoustics - Determination of sound insulation performances of enclosures - Part 1: Measure