《BS-EN-15014-2007.pdf》由会员分享，可在线阅读，更多相关《BS-EN-15014-2007.pdf（36页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15014:2007 Plastics piping systems Buried and above ground systems for water and other fluids under pressure Performance characteristics for pipes, fittings and their joints ICS 23.040.20; 23.040.45 ? Copyright British Standards Institution Provided by IHS under license with B
2、SI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 15014:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2008
3、BSI 2008 ISBN 978 0 580 54579 5 National foreword This British Standard was published by BSI. It is the UK implementation of EN 15014:2007. The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/2, Plastic piping for press
4、ure applications. This British Standard is intended as a means of demonstrating compliance with the Construction Products Directive (89/106/EEC), and affixing the CE mark. The Essential Requirements contained in this British Standard are concepts related to the Construction Products Directive and th
5、ey are not necessarily indicative of all the performance requirements or suitability for the service conditions likely to be encountered in a particular pipework application. The CE mark indicates only that a product may legally be placed on the market in the EU. It does not indicate or guarantee in
6、herent quality of the CE marked pipework components. It should be noted that manufacturers are entitled to declare “No Performance Determined” against some or all of these Essential Requirements and yet still affix the CE mark to their products. Users are advised to check the background details with
7、 the manufacturers claims for the CE marked products. Such details may be available on an appropriate Internet website or accompanying Company documentation. Compliance with this British Standard does not necessarily mean that products bearing the CE mark are fit for a particular intended purpose. T
8、his Standard does not replace the corresponding BS EN Product Standards (see national annex NA) which do contain detailed performance requirements for pipes, fittings and joints manufactured from particular plastics materials. Amendments issued since publication Amd. No. DateComments Copyright Briti
9、sh Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 15014:2007 i This British Standard makes no reference to the suitabili
10、ty of pipework for conveying drinking water. The legislation setting out these requirements for water supply installations in the UK is: for installations for public water supplies: the Water Supply (Water Quality) Regulations 2000, Regulation 31 (England), the Water Supply (Water Quality) Regulatio
11、ns 2001, Regulation 31 (Wales), the Water Supply (Water Quality) Regulations 2001, Regulation 27 (Scotland); and the Water Supply (Water Quality) Regulations 2007, Regulation 30 (Northern Ireland); and for installations for consumers premises: the Water Supply (Water Fittings) Regulations 1999 (Engl
12、and and Wales), the Water Byelaws 2000 (Scotland) and the current requirements for Northern Ireland A list of product standards used in conjunction with this standard is included in a national annex NA. A list of organizations represented on PRI/88/2 can be obtained on request to its secretary. This
13、 publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations Copyright British Standards Institution Provided by IHS under license with BSI - Un
14、controlled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- blank Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for R
15、esale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 15014 October 2007 ICS 23.040.20; 23.040.45 English Version Plastics piping systems - Buried and above ground systems for water and other fluids u
16、nder pressure - Performance characteristics for pipes, fittings and their joints Systmes de canalisations en plastique - Systmes enterrs et ariens pour eau et autres fluides avec pression - Caractristiques de performance pour tubes, raccords et leurs assemblages Kunststoff-Rohrleitungssysteme - Erd-
17、 und oberirdisch verlegte Druckrohrleitungssysteme fr Wasser und andere Flssigkeiten - Eigenschaften fr die Gebrauchstauglichkeit von Rohren, Formstcken und deren Verbindungen This European Standard was approved by CEN on 23 August 2007. CEN members are bound to comply with the CEN/CENELEC Internal
18、Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
19、This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members a
20、re the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switz
21、erland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2007 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No.
22、 EN 15014:2007: E Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15014:2007 (E) 2 Contents Page Foreword3
23、 Introduction.4 1 Scope5 2 Normative references5 3 Terms, definitions and symbols 7 4 Performance requirements.7 4.1 Reaction to fire for applications inside building7 4.2 External pressure strength.7 4.3 Internal pressure strength7 4.4 Dimensional tolerances8 4.5 Tightness (air and liquid)8 4.6 Dur
24、ability8 4.7 Dangerous substances.8 5 Test methods.9 5.1 Reaction to fire for applications inside building9 5.2 Determination of the nominal pressure 9 5.3 Internal pressure strength9 5.4 Dimensional tolerances10 5.5 Tightness10 5.6 Durability10 6 Evaluation of conformity 10 6.1 General .10 6.2 Init
25、ial type testing11 6.3 Factory production control 12 6.4 One-off products and products produced in very low quantities15 Annex A (normative) Product standards for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and
26、other fluids.17 Annex B (normative) Standards for assessment of conformity for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids 19 Annex ZA (informative) Clauses of this European Standard addressing
27、the provisions of EU Construction Products Directive.20 ZA.1 Scope and relevant characteristics.20 ZA.2 Procedure for attestation of conformity of plastics pipes and fittings21 ZA.2.1 Systems of attestation of conformity21 ZA.2.2 EC Certificate and Declaration of conformity.23 ZA.3 CE marking and la
28、belling .25 ZA.3.1 CE marking requirements.25 ZA.3.2 Simplified CE marking with reference to a web site26 ZA.3.2.1 General .26 ZA.3.2.2 Minimum rules for the proper use of a web site for CE marking information 28 Bibliography29 BS EN 15014:2007 Copyright British Standards Institution Provided by IHS
29、 under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15014:2007 (E) 3 Foreword This document (EN 15014:2007) has been prepared by Technical Committee CEN/TC 155 “Plas
30、tics piping systems and ducting systems”, the secretariat of which is held by NEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2008, and conflicting national standards shall be withdrawn
31、 at the latest by July 2009. This document has been prepared under the mandate M/131 “Pipes, tanks and ancillaries not in contact with water intended for human consumption“ given to CEN by the European Commission and the European Free Trade Association and support essential requirements of EU Direct
32、ives. For the relationship with EU Directives, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bul
33、garia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. BS EN 15014:2007 Copyright Bri
34、tish Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15014:2007 (E) 4 Introduction This European Standard contains only the
35、performance characteristics needed to meet the essential requirements of EU Directive(s). It does not cover all characteristics of the products. These are specified in the standards listed in Annex A or in other appropriate product specifications. This harmonised European Standard is part of a famil
36、y of cluster standards addressing plastics piping systems. The relationship is shown below. Material independent Specific solutions For the harmonisation of pressure plastics piping systems (this European Standard) the following applies: For pipes and fittings For valves Figure 1 BS EN 15014:2007 Co
37、pyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:53:40 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15014:2007 (E) 5 1 Scope This European Standard specifies pe
38、rformance requirements for plastics pipes, fittings and their joints for buried or above-ground pressure applications for water for general purposes, drainage, sewerage and irrigation, as well as for any other pressure application with other fluids covered by the Construction Products Directive with
39、 the exception of drinking water distribution for human consumption. It gives associated test methods for verification and evaluation of conformity with this European Standard. NOTE Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the prod
40、uct for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of this standard, pro
41、ducts conforming to this standard could be used for the transport of water intended for human consumption if they conform to the relevant national, regional or local regulatory provisions or recommendations applicable in the place of use. 2 Normative references The following referenced documents are
42、 indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals Materials requirements for pipe joint seals used in water a
43、nd drainage applications Part 1: Vulcanized rubber EN 681-2, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage applications Part 2: Thermoplastic elastomers EN 681-4, Elastomeric seals Materials requirements for pipe joint seals used in water and drainage appli
44、cations Part 4: Cast polyurethane sealing elements EN 713, Plastics piping systems Mechanical joints between fittings and polyolefin pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending EN 715, Thermoplastics piping systems End-load bearing joints b
45、etween small diameter pressure pipes and fittings Test method for leaktightness under internal water pressure, including end thrust EN 911, Plastics piping systems Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping Test method for leaktightness under extern
46、al hydrostatic pressure EN 1394, Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Determination of the apparent initial circumferential tensile strength EN 1796, Plastics piping systems for water supply with or without pressure Glass-reinforced thermosetting plastics (GRP)
47、 based on unsaturated polyester resin (UP) EN 13501-1, Fire classification of construction products and building elements Part 1: Classification using test data from reaction to fire tests EN 14364, Plastics piping systems for drainage and sewerage with or without pressure Glass-reinforced thermoset
48、ting plastics (GRP) based on unsaturated polyester resin (UP) Specifications for pipes, fittings and joints EN 15012:2007, Plastics piping systems Soil and waste discharge systems within the building structure Performance characteristics for pipes, fittings and their joints BS EN 15014:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontroll