《BS-EN-15432-2008.pdf》由会员分享，可在线阅读，更多相关《BS-EN-15432-2008.pdf（28页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 15432:2008 Winter and road service area maintenance equipments Front-mounted equipments Interchangeability ICS 43.160 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 2
2、0:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- BS EN 15432:2008 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008 ISBN 978 0 580 56159 7 National foreword This British Standard is the
3、 UK implementation of EN 15432:2008. The UK participation in its preparation was entrusted by Technical Committee B/513, Construction equipment and plant and site safety, to Panel B/513/-/16, Winter maintenance and road surface and maintenance equipment. A list of organizations represented on this c
4、ommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments/corrigenda is
5、sued since publication DateComments Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EUROPEAN STANDARD NORME E
6、UROPENNE EUROPISCHE NORM EN 15432 January 2008 ICS 43.160 English Version Winter and road service area maintenance equipments - Front- mounted equipments - Interchangeability Matriels de viabilit hivernale et dentretien des dpendances routires - Matriels monts lavant - Interchangeabilit Winterdienst
7、- und Straenbetriebsdienstausstattung - Mechanische Schnittstelle an Fahrzeugen fr frontangebaute Maschinen - Austauschbarkeit This European Standard was approved by CEN on 21 October 2007. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g
8、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official
9、versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Bel
10、gium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FO
11、R STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 15432:2008: E Copyright British Standards In
12、stitution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 2 Contents Foreword3 1 Scope.4 2 Normative references.4 3 Interchangeabil
13、ity requirements.4 3.1 Front mounting plate4 3.1.1 General provisions4 3.1.2 Mounting plate classes.5 3.1.3 Strength requirements5 3.1.4 Designation.6 3.1.5 Interchangeability dimensions6 3.1.6 Tool fixing systems.9 3.2 Electrical and hydraulic connections.9 3.2.1 General.9 3.2.2 Location on the veh
14、icle.10 3.2.3 Clearance space.12 3.2.4 Connection types13 3.2.5 Identification and preferred layout of hydraulic connections13 3.3 Mechanical Power Take Off (PTO) .14 Annex A (normative) Quick-coupling VV95 system for front mounted equipments.16 A.1 General16 A.2 Interchangeability requirements16 A.
15、2.1 Front mounting plate16 A.2.2 Electrical and hydraulic connections19 A.2.3 Mechanical Power Take Off (PTO)20 Annex B (normative) Compact F1/C front mounting plate for combined road and off-road applications.21 B.1 General21 B.2 Interchangeability requirements Front Mounting Plate21 B.2.1 General
16、provisions.21 B.2.2 Mounting plate class 21 B.2.3 Strength requirements .21 B.2.4 Designation 21 B.2.5 Interchangeability dimensions22 B.2.6 Tool fixing systems.23 Bibliography24 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/591
17、0770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 3 Foreword This document (EN 15432:2008) has been prepared by CEN/TC 337/WG 3 “Interface between tools and vehicle“, the secretariat of which is held by UNI-CUNA, u
18、nder the direction of Technical Committee CEN/TC 337 “Winter maintenance and road service area maintenance equipment“, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
19、the latest by July 2008, and conflicting national standards shall be withdrawn at the latest by July 2008. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard : Austria, Belgium, Bulgaria, Cy
20、prus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Copyright British Standards Institution
21、 Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 4 1 Scope This European Standard specifies the requirements for the various elemen
22、ts of carrying vehicles to ensure interchangeability between a vehicle and different equipments that are frontally mounted. It specifies certain interchangeability dimensions of the front mounting plate, including its height above the ground, as well as the locations of coupling devices for electric
23、al and hydraulic connections and for mechanical power take off (PTO). This European Standard specifies two different classes of mounting plates in order to cover road vehicles, having a maximum design total mass higher than 3,5 t, of the greatest possible variety (commercial vehicles, multi-purpose
24、vehicles, communal vehicles, ), which are capable of carrying front-mounted equipments for winter maintenance and for road service area maintenance. This European Standard specifies, with regard to electrical and hydraulic connections and to PTO, only location areas, clearance spaces and preferred l
25、ayout in order to ensure interchangeability. Requirements applying to connectors, coupling devices and PTO splines are given in EN 15431. Normative Annex A specifies provisions for an advanced front coupling system that is able to allow for mounting and demounting equipments without the use of tools
26、. Users having to address specific needs (e.g. extreme weather conditions) may require the vehicle be fitted with such automatic coupling system. Normative Annex B gives provisions for a compact and light front mounting plate intended for combined road and off-road applications. 2 Normative referenc
27、es The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 15431, Winter and road service area mainten
28、ance equipments Power system and related controls Interchangeability and performance requirements 3 Interchangeability requirements 3.1 Front mounting plate 3.1.1 General provisions Mounting plates of all classes, as defined in following 3.1.2, shall be designed and installed to the carrying vehicle
29、 to allow for safe and easy tilting of the cabin (if the vehicle has been designed to provide for this facility). Mounting plates of all classes, as defined in following 3.1.2, shall be designed and installed to the carrying vehicle so as to allow for mounting a front towing hitch (if the vehicle ha
30、s been designed to provide for this facility). Compliance to this requirement may be achieved in different ways, e.g. by a pivoting or folding mounting plate, by an appropriate non-obstructing design or by provisions for direct mounting of the hitch to the mounting plate itself. Characteristics of t
31、he quick-coupling system designed to allow for mounting and demounting of equipments without the use of tools are given in Annex A. Characteristics of the compact mounting plate designed for combined road and off-road applications are given in Annex B. Copyright British Standards Institution Provide
32、d by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 5 3.1.2 Mounting plate classes Table 1 gives indications on installation heights and on th
33、e recommended range of the maximum design total mass (ISO-M07, item 4.7 of ISO 1176:1990) of the carrying vehicle for each of the two classes of mounting plates that are defined in this European Standard. The installation height is measured with the carrying vehicle being at kerb mass (ISO-M06, item
34、 4.6 of ISO 1176:1990) from the ground to the upper edge of the mounting plate, as shown in Figure 2 and Figure 3. Table 1 Installation heights of mounting plate classes Mounting plate class Height mm Recommended range of carrying vehicle maximum design total mass 1) t F 1 1 000 60 7,5 F 2 870 50 3,
35、5 and 9 1) When mounting plates of classes F1 and F2 are being mounted on vehicles, which are not covered by ISO 1176, recommended ranges as given in the table may not be applicable. 3.1.3 Strength requirements Mounting plates shall be designed to withstand to the maximum loads and moments that are
36、given in Table 2 for each appropriate class. The values given in Table 2 refer to static loads and moments applied by the greatest variety of equipments (e.g. snow plough, grass cutting machine ) that may be fixed on the mounting plate. Equipments apply static loads and moment when they are being he
37、ld in a raised position for transportation and transfer purposes. Table 2 Maximum static loads Mounting plate class Vertical load, Fz kN Bending moment, My kNm Torsional moment, Mx kNm F 1 22 22 45 F 2 12 12 18 Loads and moments given in Table 2 refer to the vehicle coordinate system as shown in Fig
38、ure 1. Mounting plates shall also be able to withstand to foreseeable dynamic forces which may arise when working with equipments having maximum static loads shown in Table 2. Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/591077
39、0001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 6 Figure 1 Vehicle coordinate system 3.1.4 Designation Mounting plates meeting the requirements of this European Standard shall be identified by the following informat
40、ion, in the order given: a) reference to this European Standard (EN 15432:2008); b) indication of the mounting plate class. EXAMPLE Mounting plate of class F 2: Mounting plate EN 15432 F 2 3.1.5 Interchangeability dimensions Interchangeability dimensions of mounting plates shall be according to: Fig
41、ure 2 for Class F 1 mounting plates; Figure 3 for Class F 2 mounting plates. Dimensions not specified in Figure 2 and Figure 3 are left to the discretion of the manufacturer. Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770
42、001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 7 Dimensions in millimetres Key 1 clearance for claw 2 clearance for swivel bolts 3 clearance for swivel bolt 4 clearance for passing bolt 5 cone 6 clearance for centri
43、ng cone NOTE 1 Additional cut-outs are allowed if the stiffness is not reduced thereby. NOTE 2 Additional elements, which do not conflict with the characteristic dimensions, may be provided to couple in-use implements using different fixing systems. Figure 2 Dimensions for F 1 mounting plates Copyri
44、ght British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without license from IHS -,-,- EN 15432:2008 (E) 8 Dimensions in millimetres Key 1 clearance for c
45、law 2 clearance for swivel bolt 3 clearance for swivel bolt 4 cone 5 clearance for centring cone NOTE 1 Additional cut-outs are allowed if the stiffness is not reduced thereby. NOTE 2 Additional elements, which do not conflict with the characteristic dimensions, may be provided to couple in-use impl
46、ements using different fixing systems. Figure 3 Dimensions for F 2 mounting plates Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 20:58:22 MDTNo reproduction or networking permitted without l
47、icense from IHS -,-,- EN 15432:2008 (E) 9 3.1.6 Tool fixing systems 3.1.6.1 General To ensure interchangeability with tools already in use, mounting plates defined in this European Standard are designed in such a way as to allow for different fixing systems. The choice of the most appropriate fixing
48、 system shall be left to the tool manufacturer and to the user. The following subclauses give a description of all the fixing elements provided by each mounting plate class. Additional fixing elements that do not conflict with the characteristic dimensions given in Figure 2 and Figure 3, i.e., which do not interfere