《BS-EN-60603-10-1998 IEC-60603-10-1991.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60603-10-1998 IEC-60603-10-1991.pdf（36页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60603-10:1998 IEC 60603-10: 1991 Connectors for frequencies below 3 MHz for use with printed boards Part 10: Two-part connectors for printed boards for basic grid of 2,54 mm (0,1 in), inverted type The European Standard EN 60603-10:1998 has the status of a British Standard ICS
2、 31.220.10 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60603-10:1998 This British Standard, having been prepared under the direction of the Electrotechnical Sector Board, was published under the authority of the Standards Board and
3、 comes into effect on 15 May 1998 BSI 09-1999 ISBN 0 580 29295 9 National foreword This British Standard is the English language version of EN 60603-10:1998. It is identical with IEC 60603-10:1991. The UK participation in its preparation was entrusted by Technical Committee EPL/48, Electromechanical
4、 components for electronic equipment, to Subcommittee EPL/48/2, Connectors for electronic equipment, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and ke
5、ep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. From 1 January 1997, all IEC publications have the number 60000 added to the old
6、number. For instance, IEC 27-1 has been renumbered as IEC 60027-1. For a period of time during the change over from one numbering system to the other, publications may contain identifiers from both systems. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally inclu
7、de an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standard
8、s Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard
9、does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 30 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. T
10、his will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60603-10:1998 BSI 09-1999i Contents Page National foreword
11、Inside front cover Foreword2 Text of EN 60603-105 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUR
12、OPENNE EUROPISCHE NORM EN 60603-10 February 1998 ICS 31.220.10 Descriptors: Electronic components, electric connectors, printed-circuit cards, printed-circuit boards, designation, dimensions, assembling, couplings, tests, standard gauges, characteristics English version Connectors for frequencies be
13、low 3 MHz for use with printed boards Part 10: Two-part connectors for printed boards for basic grid of 2,54 mm (0,1 in), inverted type (IEC 60603-10:1991) Connecteurs pour frquences infrieures 3 MHz pour utilisation avec cartes imprimes Partie 10: Connecteurs pour circuits imprims en deux parties p
14、our grille de base de 2,54 mm (0,1 in), de type invers (CEI 60603-10:1991) Steckverbinder fr gedruckte Schaltungen fr Frequenzen unter 3 MHz Teil 10: Indirekte Steckverbinder fr gedruckte Schaltungen mit Raster 2,54 mm (0,1 in), invertierte Bauform (IEC 60603-10:1991) This European Standard was appr
15、oved by CENELEC on 1998-01-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nati
16、onal standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own languag
17、e and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spa
18、in, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels 1998 CENELEC All rights of exploitatio
19、n in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60603-10:1998 E Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 BSI 09-1999 2 Foreword The text of the International Standard IEC 60603-10:19
20、91, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the formal vote and was approved by CENELEC as EN 60603-10 on 1998-01-01 without any modification. The following dates were fixed: Annexes designated “n
21、ormative” are part of the body of the standard. In this standard, Annex ZA is normative. Annex ZA has been added by CENELEC. Endorsement notice The text of the International Standard IEC 60603-10:1991 was approved by CENELEC as a European Standard without any modification. Contents Page Foreword 2 1
22、 Scope 5 2 IEC type designation 6 3 Common features 6 3.1 Mounting dimensions 6 3.2 Mating Information 8 3.3 Survey of types 11 4 Dimensions 11 4.1 General 11 4.2 Fixed connectors 12 4.3 Board-mounted connectors 16 4.4 Mating information 18 4.5 Mounting information for fixed connectors 18 4.6 Mounti
23、ng information for board-mounted connectors 20 5 Gauges 21 5.1 Sizing gauges and retention force gauges 21 5.2 Test panel (for voltage proof test) 21 6 Characteristics 21 6.1 Climatic category 21 6.2 Electrical 21 7 Test schedule 23 7.1 General 23 Annex ZA (normative) Normative references to interna
24、tional publications with their corresponding European publications 30 Figure 1 General view of the connection 8 Figure 2 9 Figure 3 9 Figure 4 10 Figure 5 12 Figure 6 15 Figure 7 16 Figure 8 18 Figure 9 19 Figure 10 19 Figure 11 20 Figure 12 21 Figure 13 22 Figure 14 23 Table 1 7 latest date by whic
25、h the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 1998-12-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 1998-12-01 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:
26、57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 BSI 09-19993 Page Table 211 Table 3 Dimensions common to types T13 Table 4 Contact arrangement of types T14 Table 5 Dimensions of terminations15 Table 6 Dimensions common to types T17 Table 7 Contact arrangement of types T17 Table 818 Ta
27、ble 919 Table 1020 Table 1121 Table 1221 Table 1322 Table 1422 Table 1524 Table 1625 Table 1727 Table 1828 Table 1928 Table 2029 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 4 blank Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 0
28、2:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 BSI 09-19995 1 Scope This specification covers a group of related two-part connectors for printed boards. It describes connectors with 32, 48, 64 and 96 contacts for low-voltage applications. The board-mounted connectors with female
29、 contacts are provided with terminations suitable for printed boards in accordance with IEC 326 and using a grid of 2,54 mm (0,1 in) as laid down in IEC 97. The fixed connectors with male contacts are provided either with solder contacts or with wrap contacts. The terminations of the fixed connector
30、s are located in such a way as to be suitable for use with mother boards using a grid of 2,54 mm (0,1 in) as laid down in IEC 97 as well as for automatic wiring techniques. This standard shall be used in conjunction with the following IEC publications: Publications Nos. 50(581) (1978): International
31、 Electrotechnical Vocabulary (IEV) Chapter 581: Electromechanical components for electronic equipment. 97 (1970): Grid system for printed circuits. 194 (1988): Terms and definitions for printed circuits. 326: Printed boards. 512: Electromechanical components for electronic equipment; Basic testing p
32、rocedures and measuring methods. 603-1 (1991): Connectors for frequencies below 3 MHz for use with printed boards, Part 1: Generic specification General requirements and guide for the preparation of detail specifications, with assessed quality. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11
33、02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 6 BSI 09-1999 2 IEC type designation Connectors according to this standard shall be designated by the following system: NOTEL stands for letter. N stands for number. Example Connector type T, having 96 male gold contacts with solde
34、r terminations. Complete board-mounted connector for boards up to 1,6 mm (0,063 in): 603-10 IEC-TO96 MS-C1A. 3 Common features 3.1 Mounting dimensions 3.3.1 Reference system A line in the mounting plane of the fixed connector which passes through the nominal position of the centres of the mounting h
35、oles is used as the datum line. The nominal centre of the mounting hole near contact No. 32 is used as the datum point. The dimensions in 3.1.2 and 3.1.3 are defined with reference to this datum system. 3.1.2 Fixed connector 3.1.2.1 Position of the mounting holes. 3.1.2.2 Position of the termination
36、s. The distance between termination centres shall be 2,54 mm (0,1 in) or multiples thereof. The terminations shall be located so as to permit automatic wiring techniques. 3.1.3 Printed board assembly 3.1.3.1 Position of the board-mounted connector. 3.1.3.2 Position of the mounting holes of the board
37、-mounted connector. 3.1.3.3 Position of the printed board. Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 BSI 09-19997 3.1.3.4 Position of the grid of the printed board. The terminations of the board-mounted connectors shal
38、l fit into holes in the printed board in accordance with IEC 326 and located on a grid 2,54 mm (0,1 in) in accordance with IEC 97. 3.1.4 Isometric view and values Table 1 ReferenceDimensionLegend mmin 953,74Maximum overall length of the fixed connector 17,20,677Contact range in plug-in direction (se
39、e Figure 1) 15,60,614 NOTEFor information only, see 3.2 903,543Distance between the two mounting holes of the fixed connector 88,93,5Distance between the two mounting holes of the board-mounted connector NOTEThe mounting holes are also located on a 2.54 mm (0.1 in) grid in accordance with IEC 97 5,6
40、30,222Distance between datum point and a line through the centres of termination No. 32 of the fixed connector 0,730,029Distance between datum line and a line through the centres of the termination row “b” of the fixed connector n 2,54n 0,1Pitch of the fixed connector terminations NOTEWhere a pitch
41、of 2 2,84 = 5,08 is used the terminations shall be located on even-numbered positions 2, 4, 6 . 30, 32 3,550,14Distance between datum line and component side of the printed board 5,30,209Distance between the edge of the printed board and the first row of component holes for the board-mounted connect
42、or 2,540,1Distance between the mounting holes and the first row of component holes for the board mounted connector 5,080,2Distance between a mounting hole and the component hole for the termination No. 1 or No. 32 of the board-mounted connector 853,346Minimum length of mounting cut-out or minimum di
43、stance between mounting bars for the fixed connector 2,50,098Maximum thickness of mounting panel or bars for the fixed connector 14,20,559Range in which reliable contact is ensured 12,40,488 NOTESee 3.2 for mating information Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00
44、2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 8 BSI 09-1999 Figure 1 General view of the connection 3.2 Accouplement3.2 Mating information 3.2.1 Enfichage3.2.1 Plug-in direction La rsistance de contact spcifie est assure dans la plage u = 12,4 mm 14,2 mm (0,488 in 0,599 in). The specified contac
45、t resistance is ensured within then range u = 12,4 mm (0,488 in to 0,599 in). Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 BSI 09-19999 Figure 2 3.2.2 Enfichange perpendiculaire3.2.2 Perpendicular to plug-in direction Les
46、 embases et les fiches sont tudies de manire permettre un mauvais alignement dau moins 1 mm (0,04 in) montage flottant. The design of the board-mounted and the fixed connector is such that a displacement of at least 1 mm (0,04 in) can be accommodated, provided that the printed board or the fixed con
47、nector is float mounted. NOTEPour le montage rigide dun gabarit, des tolrances serres sont ncessaires. NOTEFor rigid mounting of a fixed connector, jig-mounting with appropriate tight tolerances is necessary. Figure 3 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Un
48、controlled Copy, (c) BSI EN 60603-10:1998 10 BSI 09-1999 3.2.3 Inclinaison3.2.3 Inclination Les embases et les fiches sont tudies de manire permettre un mauvais alignement angulaire de 4 dans laxe longitudinal et 2 dans laxe longitudinal et 2 dans laxe transversal. The design of the board-mounted an
49、d the fixed connector is such as to allow for an initial misalignment of 4 in longitudinal axis and 2 in transverse axis. Figure 4 Licensed Copy: sheffieldun sheffieldun, na, Sat Nov 11 02:23:57 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 60603-10:1998 BSI 09-199911 3.3 Tableau des types3.3 Survey of types Table 2 Type et nombre de contacts Type and number of contacts TO32TO48TO64TO96 Pas minimal entre deux connecteure n 2,54 mm (n 0,1 in) Smallest pitch of adjac