《BS-EN-607-2004.pdf》由会员分享，可在线阅读，更多相关《BS-EN-607-2004.pdf（24页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 607:2004 Eaves gutters and fittings made of PVC-U Definitions, requirements and testing The European Standard EN 607:2004 has the status of a British Standard ICS 01.040.91; 91.060.20 ? Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolle
2、d Copy, (c) BSI BS EN 607:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 26 September 2005 BSI 26 September 2005 ISBN 0 580 46125 4 National foreword This British Standard is the official English language version of EN 607:2004. It supe
3、rsedes BS EN 607:1996. Together with BS EN 12200-1:2000 and BS EN 1462:2005 it will replace BS 4576-1:1989 which is scheduled for withdrawal in September 2007. The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/1, Plas
4、tics piping systems for non-pressure applications, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this
5、document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contr
6、act. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals fo
7、r change, and keep UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 20, an inside back cover and a back cover. The BSI copyright n
8、otice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 607
9、November 2004 ICS 01.040.91; 91.060.20 Supersedes EN 607:1995 English version Eaves gutters and fittings made of PVC-U - Definitions, requirements and testing Gouttires pendantes et leurs raccords en PVC-U - Dfinitions, exigences et mthodes dessai Hngedachrinnen und Zubehrteile aus PVC-U - Begriffe,
10、 Anforderungen und Prfung This European Standard was approved by CEN on 15 July 2004. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists
11、and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsi
12、bility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
13、 Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 B
14、russels 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 607:2004: E Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:2004 (E) 2 Contents page Foreword4 1 Scope 5
15、 2 Normative references5 3 Terms and definitions .6 3.1 eaves gutter6 3.2 down-pipe.6 3.3 union-clip (gutter-union).6 3.4 joint bracket (union-bracket)6 3.5 gutter adaptor.6 3.6 angle6 3.7 stop end6 3.8 outlet .6 3.9 commercial length.6 4 Material .7 4.1 Raw material.7 4.2 Utilisation of non virgin
16、material7 5 General characteristics of profiles - Appearance.7 6 Geometrical characteristics of profiles.7 6.1 Width.7 6.2 Length.7 7 Physical and mechanical characteristics of profiles.7 8 General characteristics of fittings8 8.1 General8 8.2 Appearance 8 8.3 Shape and dimensions8 9 Physical charac
17、teristics of fittings 9 10 Gutter sealing rings.9 11 Solvent cements 9 12 Designation 10 13 Marking.10 14 Fitness for purpose of gutter systems11 15 Production control.11 Annex A (normative) Utilisation of non-virgin material12 A.1 Material definitions12 A.1.1 virgin material 12 A.1.2 own reprocessa
18、ble material .12 A.1.3 external reprocessable material.12 A.1.4 recyclable material.12 A.2 Reprocessable and recyclable material 12 A.2.1 Own reprocessable material.12 A.2.2 External reprocessable and recyclable materials with agreed specification13 A.2.3 External reprocessable and recyclable materi
19、al not covered by an agreed specification15 Annex B (normative) Impact test16 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:2004 (E) 3 Annex C (normative) Heat reversion test for fittings .17 Annex D (normative) Watertightness test
20、.18 Annex E (informative) Cross section areas.19 Bibliography20 Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:2004 (E) 4 Foreword This document (EN 607:2004) has been prepared by Technical Committee CEN/TC 128 “Roof covering product
21、s for discontinuous laying and products for wall cladding”, the secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2005, and conflicting national standards sh
22、all be withdrawn at the latest by May 2005. This document supersedes EN 607:1995. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Eston
23、ia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Unco
24、ntrolled Copy, (c) BSI EN 607:2004 (E) 5 1 Scope This document specifies requirements and test methods of eaves gutters and fittings made from unplasticized poly(vinyl chloride) (PVC-U), and intended to be used for rainwater drainage. 2 Normative references The following referenced documents are ind
25、ispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 513 Unplasticized polyvinyl chloride (PVC-U) profiles for the fabrication of windows and
26、 doors Determination of the resistance to artificial weathering EN 638 Plastics piping and ducting systems Thermoplastics pipes Determination of tensile properties EN 681-1 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized ru
27、bber EN 681-2 Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers EN 681-3 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 3: Cellular materials of vu
28、lcanized rubber EN 681-4 Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications Part 4: Cast polyurethane sealing elements EN 727 Plastics piping and ducting systems Thermoplastics pipes and fittings Determination of Vicat softening temperature (VST)
29、EN 743 Plastics piping and ducting systems Thermoplastics pipes Determination of the longitudinal reversion EN 763 Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Test method for visually assessing effects of heating EN 922 Plastics piping and ducting systems Pipes
30、and fittings of unplasticized poly(vinyl chloride) (PVC-U) Specimen preparation for determination of the viscosity number and calculation of the K-value EN 1905 Plastics piping systems Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material Method for assessment of the PVC content ba
31、sed on total chlorine content EN 10204:1991 Metallic products Types of inspection documents EN 20105-A02 Textiles - Tests for colour fastness Part A02: Grey scale for assessing change in colour (ISO 105-A02:1993) EN ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions f
32、or moulding and extrusion plastics (ISO 527-2:1993 including Corr 1:1994) EN ISO 1183-3 Plastics - Methods for determining the density of non-cellular plastics - Gas pyknometer method (ISO 1183-3:1999) Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy,
33、 (c) BSI EN 607:2004 (E) 6 EN ISO 4892-2 Plastics Methods of exposure to laboratory light sources Part 2: Xenon arc sources (ISO 4892-2:1994) EN ISO 4892-3 Plastics Methods of exposure to laboratory light sources Part 3: Fluorescent UV lamps (ISO 4892-3:1994) EN ISO 8256 Plastics - Determination of
34、tensile-impact strength (ISO 8256:1990, including Technical Corrigendum 1:1991) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 eaves gutter gutter situated outside the building and supported by brackets 3.2 down-pipe pipe fitted to a gutter
35、to lead rainwater from the gutter to the drainage system or sewer 3.3 union-clip (gutter-union) fitting for joining two gutters and supported only by those gutters 3.4 joint bracket (union-bracket) fitting for joining two gutters which is supported by the building structure 3.5 gutter adaptor fittin
36、g for joining two different shaped gutters 3.6 angle fitting for joining two gutters installed in two different directions 3.7 stop end fitting for stopping the flow, fixed at the end of a gutter or an outlet 3.8 outlet fitting for draining off the rainwater from the gutter into the down-pipe 3.9 co
37、mmercial length length of a gutter or a down-pipe which was produced in a factory Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:2004 (E) 7 4 Material 4.1 Raw material The raw material shall be PVC-U to which are added those additive
38、s that are needed to facilitate the manufacture of components conforming to the requirements of this document. When calculated on the basis of a known formulation or in case of dispute or not known formulation, determined in accordance with EN 1905 the PVC content shall be at least 80 % by mass for
39、profiles and 85 % by mass for injection-moulded fittings. 4.2 Utilisation of non virgin material Requirements for the utilisation of non-virgin materials are given in Annex A (normative). 5 General characteristics of profiles - Appearance When viewed without magnification the internal and external s
40、urfaces of gutters shall be smooth, clean and free from scoring, cavities, and other surface defects. The ends of gutters shall be cut cleanly and square to the axis of the profile. 6 Geometrical characteristics of profiles 6.1 Width Gutters shall be designated by their upper opening width (size) (S
41、ee examples of cross section areas in Annex E). The manufacturer shall declare the usable area of the cross-section of the gutter at its designed top opening width for the calculation of flow capacity. This usable area shall be either marked on the gutter or given in commercial documents. 6.2 Length
42、 The commercial length of a gutter shall have a positive tolerance when measured at 20 C. 7 Physical and mechanical characteristics of profiles The requirements for the physical and mechanical characteristics and the conditions for the respective test methods shall conform to those given in Table 1.
43、 NOTE Any conflicting parameters and requirements given in the test method standards referred to do not apply here. Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:2004 (E) 8 Table 1 Physical and mechanical characteristics of profiles
44、 Characteristics Requirement Test parameters Test method Hammer impact strength (type test) No break or crack visible without magnification Temperature (0 2) C Annex B Speed 5 mm/min Tensile strength (type test) 42 N/mm Specimen type type 2, 3 or 5 a conforming to EN ISO 527-2 EN 638 Speed 5 mm/min
45、Elongation at break (type test) 100 % Specimen type type 2, 3 or 5 a conforming to EN ISO 527-2 EN 638 Specimen type type 2, 3 or 5 a conforming to EN ISO 8256 Tensile impact strength (type test) 500 kJ/m Temperature (23 2) C EN ISO 8256 Test temperature(100 2) C Heat reversion (type and production
46、control test) 3 % Time (30 2) min EN 743 Vicat softening temperature (type test) 75 C Conforming to EN 727 EN 727 a In case of dispute, test specimen 5 shall be used. 8 General characteristics of fittings 8.1 General The following types of fittings shall conform to the requirements given in 8.2, 8.3
47、 and Clause 8: union clip, joint-bracket, gutter adaptor, angle, stop-end, outlet and expansion piece. 8.2 Appearance When viewed without magnification the internal and external surfaces of fittings shall be smooth, clean and free from scoring, cavities, and other surface defects. 8.3 Shape and dime
48、nsions The fittings shall be compatible with the shape and the dimensions of the profile or the gutter. The outlets shall be compatible with down-pipes and fittings. Licensed Copy: sheffieldun sheffieldun, na, Wed Nov 08 02:16:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 607:2004 (E) 9 9 Physica
49、l characteristics of fittings The requirements for the physical characteristics and the conditions for the respective test methods shall conform to those given in Table 2. NOTE Any conflicting parameters and requirements given in the test method standards referred to do not apply. Table 2 Physical characteristics of fittings Characteristics Requirement Test parameters Test method Temperature (150 2) C Effect of heati