《BS-EN-60335-2-30-2003.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60335-2-30-2003.pdf（32页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60335-2-30:2003 Incorporating amendments nos. 1 and 2 and corrigendum no. 1 Household and similar electrical appliances Safety Part 2-30: Particular requirements for room heaters The European Standard EN 60335-2-30:2003, incorporating amendments A1:2004 and A2:2007, has the st
2、atus of a British Standard ICS 13.120; 97.100.10 ? Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI BS EN 60335-2-30:2003 This British Standard was published under the authority of the Standards Policy and Strat
3、egy Committee on 9 September 2003 BSI 2007 ISBN 978 0 580 59495 3 National foreword This British Standard is the UK implementation of EN 60335-2-30:2003, incorporating amendments A1:2004 and A2:2007. It was derived by CENELEC from IEC 60335-2-30:2002, incorporating amendments 1:2004 and 2:2007. It s
4、upersedes BS EN 60335-2-30:1997 which is withdrawn. The start and finish of text introduced or altered by amendment is indicated in the text by tags !“. Tags indicating changes to IEC text carry the number of the IEC amendment. For example, text altered by IEC amendment 1 is indicated by !“. The UK
5、participation in its preparation was entrusted by Technical Committee CPL/61, Safety of household electrical appliances, to Subcommittee CPL/61/07, Heated appliance group. A list of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not
6、purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments 1553710 March 2005See national foreword 15901
7、Corrigendum No. 1 19 January 2006Correction to impact energy value given in 21.1 1727331 August 2007See national foreword Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 60335-2-30 NORME EU
8、ROPENNE August 2003 EUROPISCHE NORM + A1 December 2004 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2003 CENELEC - All rights
9、 of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60335-2-30:2003 E ICS 13.120; 97.100.10 Supersedes EN 60335-2-30:1997 + A1:2000 English version Household and similar electrical appliances Safety Part 2-30: Particular requirements for room heaters (IE
10、C 60335-2-30:2002) Appareils lectrodomestiques et analogues Scurit Partie 2-30: Rgles particulires pour les appareils de chauffage des locaux (CEI 60335-2-30:2002) Sicherheit elektrischer Gerte fr den Hausgebrauch und hnliche Zwecke Teil 2-30: Besondere Anforderungen fr Raumheizgerte (IEC 60335-2-30
11、:2002) This European Standard was approved by CENELEC on 2003-03-18. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliogra
12、phical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of
13、 a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland
14、, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. + A2 June 2007 Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled
15、 Copy, (c) BSI Foreword The text of document 61/2166/FDIS, future fourth edition of IEC 60335-2-30, prepared by the IEC Technical Committee 61, was submitted to the IEC-CENELEC parallel vote. As a result of the Kista meeting of CENELEC TC 61 in May 2002, a draft amendment prAA containing the relevan
16、t existing common modifications was submitted to the formal vote. The texts of the FDIS and the prAA were approved by CENELEC as a new edition of EN 60335-2-30 on 2003-03-18. This European Standard replaces EN 60335-2-30:1997 + A1:2000. The following dates are applicable: - latest date by which the
17、EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2004-03-01 - date on which national standards conflicting with the EN have to be withdrawn (dow) 2006-03-01 This part 2 has to be used in conjunction with EN 60335-1, Household and sim
18、ilar electrical appliances Safety Part 1: General requirements. It was established on the basis of the 2002 edition of that standard. Amendments and revisions of Part 1 have also to be taken into account and the dates when such changes become applicable will be stated in the relevant amendment or re
19、vision of Part 1. This part 2 supplements or modifies the corresponding clauses of EN 60335-1, so as to convert it into the European Standard: Safety requirements for electric room heaters. When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is rea
20、sonable. When this standard states “addition“, “modification“ or “replacement“, the relevant text of Part 1 is to be adapted accordingly. NOTE 1 The following numbering system is used: - subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; - unless no
21、tes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those in a replaced clause or subclause; - additional annexes are lettered AA, BB, etc.; - subclauses, notes and annexes that are additional to those in the IEC standard are prefixed with the letter
22、 Z. NOTE 2 The following print types are used: - requirements: in roman type; - test specifications: in italic type; - notes: in small roman type. Words in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are also in bold. Speci
23、al national conditions causing a deviation from this European Standard are listed in annex ZA and are in addition to those in EN 60335-1. National deviations from this European Standard are listed in Annex ZB and are in addition to those in EN 60335-1. Page 2 EN 60335-2-30:2003 Licensed Copy: London
24、 South Bank University, London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Foreword to amendment A1 The text of document 61/2689/FDIS, future amendment 1 to IEC 60335-2-30:2002, prepared by the IEC Technical Committee 61, Safety of household and similar elec
25、trical appliances, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60335-2-30:2003 on 2004-09-01. The following dates are applicable: - latest date by which the amendment has to be implemented at national level by publication of an identical national
26、standard or by endorsement (dop) 2005-06-01 - date on which national standards conflicting with the amendment have to be withdrawn (dow) 2007-09-01 This amendment supplements or modifies the corresponding clauses of EN 60335-2-30:2003. There are no special national conditions causing a deviation fro
27、m this amendment. There are no national deviations from this amendment. _ Introduction An investigation by CENELEC TC 61 has shown that all risks from products within the scope of this standard are fully covered by the Low Voltage Directive, 73/23/EEC. For products having mechanical moving parts, a
28、risk assessment in accordance with the Machinery Directive, 98/37/EC, has shown that the risks are mainly of electrical origin and consequently this directive is not applicable. However, the relevant essential safety requirements of the Machinery Directive are covered by this standard together with
29、the principal objectives of the Low Voltage Directive. Page 3 EN 60335-2-30:2003 Foreword to amendment A2 The text of document 61/3229/FDIS, future amendment 2 to IEC 60335-2-30:2002, prepared by the IEC Technical Committee 61, Safety of household and similar electrical appliances, was submitted to
30、the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A2 to EN 60335-2-30:2003 on 2007-05-01. The following dates are applicable: - latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 200
31、8-02-01 - date on which national standards conflicting with the amendment have to be withdrawn (dow) 2010-05-01 This amendment supplements or modifies the corresponding clauses of EN 60335-2-30:2003. As a consequence of endorsing amendment 2:2007 to IEC 60335-2-30:2002, the common modifications in E
32、N 60335-2-30:2003 are covered by similar IEC text and therefore withdrawn. There are no special national conditions causing a deviation from this amendment. There are no national deviations from this amendment. _ Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 0
33、3:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI CONTENTS INTRODUCTION.6 1 Scope.7 2 Normative references .8 3 Definitions 8 4 General requirement.8 5 General conditions for the tests8 6 Classification9 7 Marking and instructions.9 Page 4 EN 60335-2-30:2003 8 Protection against access to live part
34、s12 9 Starting of motor-operated appliances 13 10 Power input and current .13 11 Heating 13 12 Void .15 13 Leakage current and electric strength at operating temperature15 14 Transient overvoltages .16 15 Moisture resistance 16 16 Leakage current and electric strength.16 17 Overload protection of tr
35、ansformers and associated circuits .16 18 Endurance16 19 Abnormal operation 16 20 Stability and mechanical hazards .20 21 Mechanical strength .20 22 Construction.21 23 Internal wiring.23 24 Components.23 26 Terminals for external conductors.24 27 Provision for earthing .24 28 Screws and connections.
36、24 29 Clearances, creepage distances and solid insulation24 30 Resistance to heat and fire.24 31 Resistance to rusting25 32 Radiation, toxicity and similar hazards25 Annexes .28 Bibliography29 25 Supply connection and external flexible cords 24 FOREWORD.2 Licensed Copy: London South Bank University,
37、 London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Page 5 EN 60335-2-30:2003 Figure 101 Examples of immediate surrounds of air-outlet grilles.26 Table 101 Temperature rises for surfaces15 Figure 102 Examples of the immediate surrounds of fireguards .27 Lice
38、nsed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI INTRODUCTION It has been assumed in the drafting of this International Standard that the execution of its provisions is entrusted to appropriately qualified and exper
39、ienced persons. This standard recognizes the internationally accepted level of protection against hazards such as electrical, mechanical, thermal, fire and radiation of appliances when operated as in normal use taking into account the manufacturers instructions. !It also covers abnormal situations t
40、hat can be expected in practice and takes into account the way in which electromagnetic phenomena can affect the safe operation of appliances.“ This standard takes into account the requirements of IEC 60364 as far as possible so that there is compatibility with the wiring rules when the appliance is
41、 connected to the supply mains. However, national wiring rules may differ. If an appliance within the scope of this standard also incorporates functions that are covered by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as far as is reasonable. If applicable
42、, the influence of one function on the other is taken into account. An appliance that complies with the text of this standard will not necessarily be considered to comply with the safety principles of the standard if, when examined and tested, it is found to have other features that impair the level
43、 of safety covered by these requirements. An appliance employing materials or having forms of construction differing from those detailed in the requirements of this standard may be examined and tested according to the intent of the requirements and, if found to be substantially equivalent, may be co
44、nsidered to comply with the standard. Page 6 EN 60335-2-30:2003 #When a part 2 standard does not include additional requirements to cover hazards dealt with in Part 1, Part 1 applies. NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is not
45、necessary to specify particular requirements for the appliance in question over and above the general requirements. This standard is a product family standard dealing with the safety of appliances and takes precedence over horizontal and generic standards covering the same subject. NOTE 2 Horizontal
46、 and generic standards covering a hazard are not applicable since they have been taken into consideration when developing the general and particular requirements for the IEC 60335 series of standards. For example, in the case of temperature requirements for surfaces on many appliances, generic stand
47、ards, such as ISO 13732-1 for hot surfaces, are not applicable in addition to Part 1 or part 2 standards.$ Licensed Copy: London South Bank University, London South Bank University, Sat Sep 01 03:27:34 GMT+00:00 2007, Uncontrolled Copy, (c) BSI HOUSEHOLD AND SIMILAR ELECTRICAL APPLIANCES SAFETY Part
48、 2-30: Particular requirements for room heaters 1 Scope This clause of Part 1 is replaced by the following. This International Standard deals with the safety of electric room heaters for household and similar purposes, their rated voltage being not more than 250 V for single-phase appliances and 480
49、 V for other appliances. NOTE 101 Examples of appliances that are within the scope of this standard are convector heaters; fan heaters; heaters for use in greenhouses. liquid-filled radiators; panel heaters; radiant heaters; tubular heaters; Appliances not intended for normal household use but which nevertheless may be a source of danger to the public, such as appliances intended to be used by laymen in the shops, in light industry an