《BS-EN-60998-2-2-2004.pdf》由会员分享，可在线阅读，更多相关《BS-EN-60998-2-2-2004.pdf（24页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN 60998-2-2:2004 Connecting devices for low-voltage circuits for household and similar purposes Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units The European Standard EN 60998-2-2:2004 has the status of a British St
2、andard ICS 29.120.20 ? Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN 60998-2-2:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 7 June 2004 BSI 7 June 2004 ISBN 0 580 4384
3、8 1 National foreword This British Standard is the official English language version of EN 60998-2-2:2004. It was derived by CENELEC from IEC 60998-2-2:2002. It supersedes BS EN 60998-2-2:1994 which will be withdrawn on 1 April 2006. The CENELEC common modifications have been implemented at the appr
4、opriate places in the text and are indicated by tags . The UK participation in its preparation was entrusted by Technical Committee PEL/23, Electrical accessories, to Subcommittee PEL/23/2, Connecting devices, which has the responsibility to: A list of organizations represented on this subcommittee
5、can be obtained on request to its secretary. Cross-references The British Standards which implement international or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search
6、” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obli
7、gations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary
8、of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 21 and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. DateComments Licensed Copy: sheffiel
9、dun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD EN 60998-2-2 NORME EUROPENNE EUROPISCHE NORM April 2004 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektro
10、technische Normung Central Secretariat: rue de Stassart 35, B - 1050 Brussels 2004 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60998-2-2:2004 E ICS 29.120.20 Supersedes EN 60998-2-2:1993 English version Connecting devices for
11、low-voltage circuits for household and similar purposes Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units (IEC 60998-2-2:2002, modified) Dispositifs de connexion pour circuits basse tension pour usage domestique et analogue Partie 2-2: R
12、gles particulires pour dispositifs de connexion en tant que parties spares avec organes de serrage sans vis (CEI 60998-2-2:2002, modifie) Verbindungsmaterial fr Niederspannungs-Stromkreise fr Haushalt und hnliche Zwecke Teil 2-2: Besondere Anforderungen fr Verbindungsmaterial als selbstndige Betrieb
13、smittel mit schraubenlosen Klemmstellen (IEC 60998-2-2:2002, modifiziert) This European Standard was approved by CENELEC on 2004-03-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a natio
14、nal standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in
15、 any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Cyprus, Czech Republic, D
16、enmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:
17、00 2006, Uncontrolled Copy, (c) BSI EN 69908-2-2:0240 - - 2 Foreword The text of the International Standard IEC 60998-2-2:2002, prepared by SC 23F, Connecting devices, of IEC TC 23, Electrical accessories, together with common modifications prepared by the CENELEC Reporting Secretariat SR 23F, was s
18、ubmitted to the formal vote and was approved by CENELEC as EN 60998-2-2 on 2004-03-01. This European Standard supersedes EN 60998-2-2:1993. The following dates were fixed: latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endor
19、sement (dop) 2005-03-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2007-03-01 This Part 2-2 is intended to be used in conjunction with EN 60998-1:2004. It supplements or modifies the corresponding clauses in EN 60998-1, so as to convert it into the
20、 European Standard: Particular requirements for connecting devices as separate entities with screwless-type clamping units. Where a particular subclause of Part 1 is not mentioned in this Part 2-2, that subclause applies as far as is reasonable. Where this standard states “addition”, “modification”
21、or “replacement”, the relevant text in Part 1 should be adapted accordingly. In this standard, a) the following print types are used: - requirements proper: in roman type; - test specifications: in italic type; - explanatory matter: in smaller roman type. b) Subclauses and figures which are addition
22、al to those in Part 1 are numbered starting from 101; additional annexes are lettered AA, BB, etc. _ Endorsement notice The text of the International Standard IEC 60998-2-2:2002 was approved by CENELEC as a European Standard with agreed common modifications. _ Page 2 EN 6099822:2004 Licensed Copy: s
23、heffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 069-89-22 IE:C2002 3 CONTENTS 1 Scope.4 2 Normative references .4 3 Definitions 4 4 General 5 5 General notes on tests .5 6 Main characteristics5 7 Classification5 8 Marking 5 9 Protection against electric sho
24、ck 6 10 Connection of conductors.6 11 Construction.10 12 Resistance to ageing, to humid conditions, to ingress of solid foreign objects and to harmful ingress of water .11 13 Insulation resistance and electric strength11 14 Mechanical strength .11 15 Temperature rise13 16 Resistance to heat14 17 Cle
25、arances and creepage distances .14 18 Resistance of insulating material to abnormal heat and fire 14 19 Resistance of insulating material to tracking.15 20 EMC requirement .15 Annex AA (normative) Number of sets of samples to be submitted to the tests 19 Annex BB (informative) Text deleted.20 Annex
26、CC (informative) Examples for temperature-rise test according to 15.4 .21 Figure 101 Test apparatus according to 10.105 .15 Figure 102 Examples of screwless-type clamping units16 Figure 103 Information for the bending test17 Figure CC.1 Temperature-rise test examples 21 Table 101 Rated connecting ca
27、pacity and connectable conductors 7 Table 102 Relationship between mass, height and cross-sectional area of conductors.9 Table 103 Relationship between pull force and cross-sectional area9 Table 104 Deflection test forces.12 Table AA.1 Number of sets of samples and test sequences .19 Page 3 EN 60998
28、22:2004 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 069-89-22 IE:C2002 4 CONNECTING DEVICES FOR LOW-VOLTAGE CIRCUITS FOR HOUSEHOLD AND SIMILAR PURPOSES Part 2-2: Particular requirements for connecting devices as separate entities with sc
29、rewless-type clamping units 1 Scope This clause of Part 1 is applicable. Addition: This standard applies to connecting devices with screwless-type clamping units primarily suitable for connecting unprepared conductors. In this standard, screwless-type terminals are referred to as terminals. NOTE Thi
30、s standard does not include insulation piercing connecting devices (IEC 60998-2-3), twist-on connecting devices (IEC 60998-2-4) and flat, quick-connect terminations (IEC 60998-2-5). 2 Normative references This clause of Part 1 is applicable. 3 Definitions This clause of Part 1 is applicable except a
31、s follows: Addition: 3.101 screwless-type terminal terminal for the connection and subsequent disconnection of two or more conductors, the connection being made directly or indirectly by means of springs, wedges, or the like NOTE Examples of screwless-type terminals are given in Figure 102. 3.101.1
32、universal terminal terminal for the connection and disconnection of all types of conductors (rigid and flexible) 3.101.2 non-universal terminal terminal for the connection and disconnection of a certain kind of conductor only (for example, solid conductors only or rigid solid and stranded conductors
33、 only) Page 4 EN 6099822:2004 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 069-89-22 IE:C2002 5 3.101.3 push-wire terminal non-universal terminal in which the connection is made by pushing in rigid (solid or stranded) conductors 4 General
34、 This clause of Part 1 is applicable. 5 General notes on tests This clause of Part 1 is applicable except as follows: 5.3 Replacement: The tests are carried out in the sequence listed for each set in Annex AA. 5.4 Replacement of the first sentence by the following: The necessary number of new sample
35、s to be submitted to the tests are divided into sets as detailed in Annex AA and this standard is met if all tests are satisfied. 6 Main characteristics This clause of Part 1 is applicable. 7 Classification This clause of Part 1 is applicable except as follows: Addition: 7.101 Classification accordi
36、ng to the types of conductors which the terminal can accept 7.101.1 Universal terminal 7.101.2 Non-universal terminal terminals for solid conductors ; terminals for rigid conductors; terminals for flexible conductors. 8 Marking This clause of Part 1 is applicable except as follows: Page 5 EN 6099822
37、:2004 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 069-89-22 IE:C2002 6 8.101 Addition: Non-universal terminals classified according to 7.101.2 shall be marked as follows: with the letter(s) “s” or “sol” for terminals declared for solid c
38、onductors; with the letter “r” for terminals declared for rigid conductors; with the letter “f” for terminals declared for flexible conductors. This marking shall appear where it is practical on the end product or on the smallest package unit or in technical information and/or catalogues. 8.102 Addi
39、tion: An appropriate marking indicating the length of insulation to be removed before insertion of the conductor into the terminal shall be shown on the product or on the smallest package unit or in technical information and/or catalogues. 9 Protection against electric shock This clause of Part 1 is
40、 applicable. 10 Connection of conductors This clause of Part 1 is applicable except as follows: Addition: 10.101 The connection or disconnection of conductors shall be made either by the use of a general purpose tool or a convenient device integral with the terminal to open it and to assist the inse
41、rtion or the withdrawal of the conductors (for example, for universal terminals); or by simple insertion. For the disconnection of the conductors an operation other than a pull on the conductor only shall be necessary (for example, for push-wire terminals). 10.102 Terminals shall accept two or more
42、conductors of the same or of different nominal cross-sectional areas or compositions if applicable. Universal terminals shall accept rigid (solid or stranded) and flexible unprepared conductors. Non-universal terminals shall accept the types of conductors declared by the manufacturer. The relationsh
43、ip between the rated connecting capacity of clamping units and connectable conductors as well as data on diameters of conductors are given in Table 101. Page 6 EN 6099822:2004 Licensed Copy: sheffieldun sheffieldun, na, Fri Nov 10 08:30:35 GMT+00:00 2006, Uncontrolled Copy, (c) BSI 069-89-22 IE:C200
44、2 7 10.103 Each terminal shall accept conductors of cross-sectional areas and types as indicated in Table 101, for the relevant values of the rated connecting capacity. Terminals shall provide, in addition, appropriate connection of at least the two successive smaller cross- sectional areas, for exa
45、mple: a) a terminal having the rated connecting capacity of 1 mm shall clamp reliably a rigid and/or flexible conductor of 0,5 mm, 0,75 mm and 1 mm; b) a terminal having the rated connecting capacity of 10 mm shall clamp reliably rigid conductors of 4 mm, 6 mm and 10 mm and/or flexible conductors of
46、 4 mm and 6 mm. c) a terminal having the rated connecting capacity of 25 mm shall clamp reliably rigid conductors of 10 mm, 16 mm and 25 mm and/or flexible conductors of 6 mm, 10mm and 16 mm. d) a terminal for flexible conductors only and having a rated connecting capacity of 25 mm shall clamp relia
47、bly flexible conductors of 10 mm, 16 mm and 25 mm. (Exception: special types of terminals may accept a smaller range of cross-sectional areas as declared by the manufacturer.) Table 101 Rated connecting capacity and connectable conductors Connectable conductors and their theoretical diameters Metric
48、 Rigid Flexible Rated connecting capacity Solid Stranded mm mm mm mm mm mm 0,2 0,34 0,5 0,2 0,34 0,5 0,51 0,63 0,9 0,53 0,66 1,1 0,2 0,34 0,5 0,61 0,8 1,1 0,75 0,75 1,0 1,2 0,75 1,3 1,0 1,0 1,2 1,4 1,0 1,5 1,5 1,5 1,5 1,7 1,5 1,8 2,5 2,5 1,9 2,2 2,5 2,3 a 4,0 4,0 2,4 2,7 4,0 2,9 a 6,0 6,0 2,9 3,3 4,
49、0 2,9 a 10,0 10,0 3,7 4,2 6,0 3,9 16,0 16,0 4,6 5,3 10,0 5,1 25,0 25,0 - 6,6 16,0 6,3 35,0 35,0 - 7,9 25,0 7,8 Text deleted NOTE 2 Diameters of the largest rigid and flexible conductors are based on Table 1 of IEC 60228 and IEC 60344 Text deleted. a Dimensions for Class 5 flexible conductors only, acc