《BS-ISO-12240-2-1998.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-12240-2-1998.pdf（12页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 12240-2:1998 Spherical plain bearings Part 2: Angular contact radial spherical plain bearings ICS 21.100.10 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 This British Standard, having been prepar
2、ed under the direction of the Engineering Sector Committee, was published under the authority of the Standards Committee and comes into effect on 15 November 1998 BSI 06-1999 ISBN 0 580 30791 3 National foreword This British Standard reproduces verbatim ISO 12240-2:1998 and implements it as the UK n
3、ational standard. The UK participation in its preparation was entrusted to Technical Committee MCE/7, Rolling bearings, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals
4、 for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement internatio
5、nal or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include a
6、ll the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i an
7、d ii, the ISO title page, pages ii to iv, pages 1 to 3 and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments Lic
8、ensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 BSI 06-1999i Contents Page National foreword Inside front cover Foreword iii Text of ISO 12240-21 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006
9、, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 ii BSI 06-1999 Contents Page
10、 Forewordiii 1Scope 1 2Normative references1 3Definitions and symbols1 4Dimensions and tolerances1 Figure 1 Angular contact radial spherical plain bearing, dimension series A1 Table 1 Dimensions for angular contact radial spherical plain bearings, dimension series A 2 Table 2 Tolerances for inner ri
11、ng and bearing width3 Table 3 Tolerances for outer ring3 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 BSI 06-1999iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of nation
12、al standard bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internation
13、al organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committee
14、s are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 12240-2 was prepared by Technical Committee ISO/TC 4, Rolling bearings, Subcommittee SC 7, Spherical plain bea
15、rings. ISO 12240 consists of the following parts, under the general title Spherical plain bearings: Part 1: Radial spherical plain bearings; Part 2: Angular contact radial spherical plain bearings; Part 3: Thrust spherical plain bearings; Part 4: Spherical plain bearing rod ends. Descriptors: Bearin
16、gs, plain bearings, spherical bearings, radial bearings, form specifications, dimensions, dimensional tolerances. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00
17、:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 BSI 06-19991 1 Scope This part of ISO 12240 specifies dimensions and tolerances for angular contact radial spherical plain bearings. The specified tolerance values apply to finished, angular contact radial spherical plain bearings before any c
18、oating or plating. Angular contact radial spherical plain bearings need not conform to the design illustrated but compliance is required as regards dimensions and tolerances specified. NOTEAngular contact radial spherical plain bearings for airframe applications are not covered by this part of ISO 1
19、2240. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of ISO 12240. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on thi
20、s part of ISO 12240 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 582:1995, Rolling bearings Chamfer dimensions Maximum values. ISO 1132-1:
21、, Rolling bearings Tolerances Part 1: Terms and definitions1). ISO 6811:1998, Spherical plain bearings Vocabulary. 3 Definitions and symbols For the purposes of this part of ISO 12240, the definitions given in ISO 1132-1 and ISO 6811 apply. The symbols (except those for tolerances) shown in Figure 1
22、 and the values given in the tables denote nominal dimensions unless specified otherwise. 4 Dimensions and tolerances 4.1 Dimensions See Figure 1 and Table 1. 1) To be published. (Revision of ISO 1132:1980) BInner ring width COuter ring width DOutside diameter D1Bore diameter of outer ring dBore dia
23、meter d1Outside diameter of inner ring dkSphere diameter rs minaSmallest single chamfer dimension, inner ring r1s minaSmallest single chamfer dimension, outer ring sDistance between sphere diameter centre and inner ring back face TBearing width VDmpVariation of mean outside diameter VdmpVariation of
24、 mean bore diameter VDpVariation of outside diameter in a single radial plane VdpVariation of bore diameter in a single radial plane BsDeviation of a single inner ring width CsDeviation of a single outer ring width DmpDeviation of mean outside diameter in a single plane dmpDeviation of mean bore dia
25、meter in a single plane TsDeviation of the actual bearing width a The corresponding maximum chamfer dimensions are given in Table 1 of ISO 582:1995. Figure 1 Angular contact radial spherical plain bearing, dimension series A Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2
26、006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 2 BSI 06-1999 Table 1 Dimensions for angular contact radial spherical plain bearings, dimension series A Dimensions in millimetres dDB max. C max. Tdk a d1 . D1 max. s . rs, r1s min. 25471514154241,53210,6 28521615164746,53611 30551716175049,53721
27、32581716175251,54021 35621817185655,54321 40681918196160,54821 45752019206766,55431 50802019207473,56041 559023222381806351,5 609523222387866951,5 6510023222393927761,5 701102524251021018371,5 751152524251061058771,5 80125292729115113,59291,5 8513029272912111998101,5 90140323032129127104112 95145323
28、032133131,510992 100150323132141138,5115122 105160353335149146,5120132,5 110170383638158155127142,5 120180383738169165137162,5 130200454345188184149182,5 140210454345198194162192,5 150225484648211207172203 160240514951225221183203 170260575557246242195213 180280646164260256207213 1902906462642752702
29、13263 200310706670290285230263 aReference only. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 BSI 06-19993 4.2 Tolerances See Table 2 and Table 3. Table 2 Tolerances for inner ring and bearing width Table 3 Tolerances f
30、or outer ring d mm dmp 4m Vdp 4m Vdmp 4m Bs 4m Ts 4m overincludinghighlowmax.max.highlowhighlow 500 121290 240+ 250 400 50800 1515110 300+ 250 500 801200 2020150 400+ 250 600 1201800 2525190 500+ 350 700 1802000 3030230 600+ 350 800 D mm Dmp 4m VDp 4m VDmp 4m Cs 4m overincludinghighlowmax.max.highlo
31、w 500 1414110 240 50800 1616120 300 801200 1818140 400 1201500 2020150 500 1501800 2525190 500 1802500 3030230 600 2503150 3535260 700 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 12240-2:1998 BSI 389 Chiswick High Road London W4 4
32、AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision.
33、 Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Se
34、cretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. B
35、uying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been publishe
36、d as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available whic
37、h give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other ben
38、efits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patent
39、s Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary d
40、etails such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:15:53 GMT+00:00 2006, Uncontrolled Copy, (c) BSI