《BS-ISO-13775-2-2000.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-13775-2-2000.pdf（22页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 13775-2:2000 ICS 2
2、3.040.70; 43.060.40 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Thermoplastic tubing and hoses for automotive use Part 2: Petroleum-based fuel applications Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This Briti
3、sh Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 April 2000 BSI 04-2000 ISBN 0 580 34264 6 BS ISO 13775-2:2000 Amendments issued since publication Amd. N
4、o.DateComments National foreword This British Standard reproduces verbatim ISO 13775-2:2000 and implements it as the UK national standard. The UK participation in its preparation was entrusted by Technical Committee PRI/66, Rubber and plastics tubing, hoses and hose assemblies, to Subcommittee PRI/6
5、6/2, Automotive applications,which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European
6、 developments and promulgate them in the UK. A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogu
7、e under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct
8、application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to v, a blank page, pages 1 to 13, and a back cover. The BSI copyright notice display
9、ed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 13775-2:2000(E) INTERNATIONAL STANDARD ISO 13775-2 First edition 2000-02-01 Thermoplastic tubing and hoses
10、for automotive use Part 2: Petroleum-based-fuel applications Tubes et tuyaux en thermoplastique pour lindustrie automobile Partie 2: Applications pour carburants base de ptrole Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 13775-2:2000
11、(E) ii? Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 13775-2:2000(E) ?iii Contents?Page Foreword.iv Introduction.v 1?Scope 1 2?Normative references1 3?Classification and materials.2 4?Dimensions.2 5?Requirements for approval of produc
12、ts3 6?Marking.5 Annex A (informative) Example of how a non-standard type of tubing or hose could be specified using a matrix.6 Annex B (normative) Method for determining the resistance to surface-contaminating fluids .7 Annex C (normative) Method of test for flame resistance8 Licensed Copy: sheffiel
13、dun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 13775-2:2000(E) iv? Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is n
14、ormally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part i
15、n the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the tec
16、hnical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 13775 may be the subject of patent ri
17、ghts. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 13775-2 was prepared by Technical Committee ISO/TC 45,Rubber and rubber products, Subcommittee SC 1,Hoses (rubber and plastics). ISO 13775 consists of the following parts, under the gene
18、ral titleThermoplastic tubing and hoses for automotive use: Part 1: Non-fuel applications Part 2: Petroleum-based-fuel applications Annexes A, B and C of this part of ISO 13775 are for information only. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy
19、, (c) BSI ISO 13775-2:2000(E) ?v Introduction This specification defines the requirements of extruded thermoplastic tubing/hoses for petroleum-based-fuel applications for automotive use. In addition, it may also be applied as a classification system to enable original equipment manufacturers (OEMs)
20、to detail a “line call-out” of tests for specific applications where these are not covered by the six main types (see example in annex A). In this case, the tubing or hose would not carry any marking showing this ISO specification number, but may detail the OEMs own identification markings as shown
21、on their part drawings. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARD?ISO 13775-2:2000(E) ?1 Thermoplastic tu
22、bing and hoses for automotive use Part 2: Petroleum-based-fuel applications WARNING Persons using this part of ISO 13775 should be familiar with normal laboratory practice. This part of ISO 13775 does not purport to address all of the safety problems, if any, associated with its use. It is the respo
23、nsibility of the user to establish appropriate safety and health practices and to ensure compliance with any national regulatory conditions. 1?Scope This part of ISO 13775 specifies test requirements and test methods for extruded thermoplastic tubing and hoses for use in petroleum-based-fuel lines i
24、n vehicles powered by internal-combustion engines. This specification is intended especially for use by original equipment manufacturers (OEMs). 2?Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of IS
25、O 13775. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 13775 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated bel
26、ow. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 188,Rubber, vulcanized or thermoplastic Accelerated ageing and heat resistance tests. ISO 1402,Rubber and plastics h
27、oses and hose assemblies Hydrostatic testing. ISO 1746,Rubber or plastics hoses and tubing Bending tests. ISO 1817,Rubber, vulcanized Determination of the effect of liquids. ISO 4639-3:1995,Rubber tubing and hoses for fuel circuits for international-combustion engines Specification Part 3: Oxidized
28、fuels. ISO 4925,Road vehicles Non-petroleum base brake fluid. ISO 7628-2:1998,Road vehicles Thermoplastics tubing for use in air braking systems Part 2: Mounting on vehicle and test methods. ISO 8031,Rubber and plastic hoses and hose assemblies Determination of electrical resistance. ISO 8033,Rubber
29、 and plastics hose Determination of adhesion between components. ISO 8308,Rubber and plastics hoses and tubing Determination of transmission of liquids through hose and tubing walls. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 13775-
30、2:2000(E) 2? ISO 11758,Rubber and plastics hoses Exposure to a xenon arc lamp Determination of changes in colour and appearance. 3?Classification and materials The product shall consist of an extruded thermoplastic material with or without an integral reinforcement. The product may also have an inne
31、r veneer to impart improved fluid resistance and/or reduced fuel vapour permeability. It may also have an extruded outer cover to improve environmental resistance and/or flame resistance. The outer cover is not necessarily bonded to the tubing or hose. Six types of tubing and hose for specific appli
32、cations are specified as follows: Type 1: feed and return lines from the fuel tank to the engine compartment gasoline engines; Type 2: feed and return lines from the fuel tank to the engine compartment diesel engines; Type 3: feed and return lines in the engine compartment moderate-temperature (100
33、?C) environment gasoline engines; Type 4: feed and return lines in the engine compartment high-temperature (125 ?C) environment gasoline engines; Type 5: feed lines in the engine compartment diesel engines; Type 6: multi-layer tubing or hoses for vapour lines. 4?Dimensions Bore diameters and wall th
34、icknesses shall be as given in Table 1. The wall thickness shall be the sum of the individual thicknesses of the various elements in the construction of the tubing or hose. The thickness of each individual element shall be such that it is able to carry out its own function and the total function of
35、the tubing or hose. Table 1 Nominal bores, internal diameters and wall thicknesses Nominal bore?Internal diameter mm Wall thickness (min.) mm 2?2 ? 0,1?0,9 4?4 ? 0,1?0,9 6?6 ? 0,1?0,9 6?6 ? 0,1?1,35 7,5?7,5 ? 0,1?1,12 8?8 ? 0,1?0,9 8?8 ? 0,1?1,35 9?9 ? 0,1?1,35 10?10 ? 0,1?1,8 12?12 ? 0,1?1,35 12?12
36、 ? 0,1?1,8 14?14 ? 0,1?1,8 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 13775-2:2000(E) ?3 5?Requirements for approval of products The following tests shall be selected for each application of the tubing or hose, based on the performa
37、nce requirements of the finished product. The tests to be carried out for each type of tubing or hose classified in clause 3 are given in Table 2. a)?Burst pressure: When determined in accordance with ISO 1402, the minimum burst pressure for all constructions shall be 55 bar gauge (5,5 MPa). b)?Cold
38、impact resistance:Aftercoldimpacttestingat? 40 Cinaccordancewithsubclause 7.4of ISO 7628-2:1998, all constructions shall show no evidence of external fracture or cracking and shall meet the burst pressure requirements of a). c)?Heat ageing resistance: After ageing at one or more of the following set
39、s of conditions in accordance with ISO 188, all constructions shall meet the cold impact requirements of b): 1)?1 000 h at 70 C 2)?1 000 h at 100 C 3)?1 000 h at 125 C 4)?168 h at 100 C 5)?168 h at 125 C 6)?168 h at 140 C d)?Resistance to light: All constructions shall meet the cold impact requireme
40、nts of b) after 1 000 kJ/m2xenon-arc exposure in accordance with ISO 11758. NOTE?This test is for applications that require exposure to daylight either during normal vehicle usage or on chassis that may be stored in the open prior to final assembly of the vehicle. e)?Resistance to fuels: When tested
41、 in accordance with annex D of ISO 4639-3:1995, using one or more of the following test fuels, all constructions shall meet the cold impact requirements of b) and the adhesion requirements of k) where applicable: 1)?A mixture of 85 % by volume of liquid C (ISO 1817) and 15 % by volume of methanol. 2
42、)?A mixture of 15 % by volume of liquid C (ISO 1817) and 85 % by volume of methanol. 3)?A mixture of 85 % by volume of liquid C (ISO 1817) and 15 % by volume of methyl tertiary-butyl ether (MTBE). 4)?Liquid F (ISO 1817) (simulated diesel fuel), with or without 10 % by volume of rape seed methyl este
43、r. 5)?PN180 oxidized fuel in accordance with annex A of ISO 4639-3:1995. f)?Resistance to stress cracking: When tested in accordance with subclause 7.9 of ISO 7628-2:1998, all constructions shall show no evidence of stress cracking and shall meet the cold impact requirements of b). g)?Resistance to
44、battery acid: When tested in accordance with subclause 7.11 of ISO 7628-2:1998, all constructions shall show no evidence of cracking or degradation and shall meet the cold impact requirements of b). h)?Resistance to surface contamination by engine oil and petroleum-based hydraulic fluid: When tested
45、 in accordance with annex B, using ISO 1817 Oil 3, all constructions shall meet the cold impact requirements of b) and the adhesion requirements of k) where applicable. i)?Resistance to surface contamination by non-petroleum hydraulic (brake/clutch) fluid: When tested in accordance with annex B, usi
46、ng hydraulic fluid to ISO 4926, all constructions shall meet the cold impact requirements of b) and the adhesion requirements of k) where applicable. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 06:53:18 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 13775-2:2000(E) 4? j)?Adhesion: For any
47、 constructions with two or more co-extruded or bonded layers only: When determined in accordance with the appropriate procedure of ISO 8033, the separation force between bonded layers shall not be less than 1,5 kN/m. k)?Flame resistance: When tested in accordance with annex C, the tubing or hose sha
48、ll withstand a minimum of 60 s exposure to flame without loss of pressure. l)?Internal cleanliness: When determined in accordance with annex B of ISO 4639-3:1995, the insoluble impurities shall not exceed 5 g/m2and the fuel-soluble impurities shall not exceed 3 g/m2. m)Fuel permeability: When determ
49、ined in accordance with ISO 8308, the permeability to a mixture of 85 % by volume of liquid C (ISO 1817) and 15 % by volume of methanol shall not exceed 25 g/m2/24 h. n)?Electrical resistance: When determined in accordance with ISO 8031, the electrical resistance shall not exceed 10 M?. o)?Resistance to kinking: When determined in accordance with ISO 1746, the