《BS-EN-ISO-10366-1-1999.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-10366-1-1999.pdf（18页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 10366-1:1999 Incorporating Amendment No. 1 to BS ISO 10366-1:1993 (renumbers the BS ISO as BS EN ISO 10366-1:1999) Plastics Methyl methacrylate/ acrylonitrile/butadiene/ styrene (MABS) moulding and extrusion materials Part 1: Designation system and basis for specifications
2、 The European Standard EN ISO 10366-1:1999 has the status of a British Standard ICS 83.080.20 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10366-1:1999 This British Standard, having been prepared under the direction of the Secto
3、r Board for Materials and Chemicals, was published under the authority of the Standards Board and comes into effect on 15 May 1995 BSI 04-2000 The following BSI references relate to the work on this standard: Committee reference PRI/33 Draft for comment 91/40476 DC ISBN 0 580 24205 6 Committees resp
4、onsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PRI/33, Styrene plastics, upon which the following bodies were represented: British Plastics Federation British Telecommunications plc Federation of the Electronics Industry Institute of M
5、aterials Ministry of Defence Amendments issued since publication Amd. No.DateComments 10663November 1999 Implementation of the European Standard Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10366-1:1999 BSI 04-2000i Contents Pag
6、e Committees responsibleInside front cover National forewordii Foreword2 Forewordiii Text of ISO 10366-11 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10366-1:1999 ii BSI 04-2000 National foreword This British Standard is the En
7、glish language version of EN ISO 10366-1:1999. This British Standard is published under the direction of the Sector Board for Materials and Chemicals whose Technical Committee PRI/33 has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any en
8、quiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. NOTEInternational and European Standards, as well as overseas standards, are available from Customer Services, BSI, 389 C
9、hiswick High Road, London W4 4AL. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary
10、 of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 6, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated
11、. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10366-1 May 1999 ICS 83.080.20 English version Plastics Methy
12、l methacrylate/acrylonitrile/butadiene/ styrene (MABS) moulding and extrusion materials Part 1: Designation system and basis for specifications (ISO 10366-1:1993) Plastiques Mthylmthacrylate/acrylonitrile/butadine/ styne (MABS) pour moulage et extrusion Partie 1: Systme de dsignation et base de spei
13、fication (ISO 10366-1:1993) Kunststoffe Methylmethylacrylat/ Acrylnitril/Butadien/Styrol (MABS)-Formmassen Teil 1: Bezeichnungssystem und Basis fr Spezifikationen (ISO 10366-1:1993) This European Standard was approved by CEN on 16 April 1999. CEN members are bound to comply with the CEN/CENELEC Inte
14、rnal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN membe
15、r. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members
16、are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisati
17、on Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1999 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10366-1:1999 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+
18、00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10366-1:1999 BSI 04-2000 2 Foreword The text of the International Standard from Technical Committee ISO/TC 61, Plastics, of the International Organization for Standardization (ISO) has been taken over as a European Standard by Technical Committee CEN/TC
19、249, Plastics, the Secretariat of which is held by IBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 1999, and conflicting national standards shall be withdrawn at the latest by Novemb
20、er 1999. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, No
21、rway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of the International Standard ISO 10366-1:1993 has been approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Annex ZA (normativ
22、e). Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10366-1:1993(E) ii BSI 04-2000 Contents Page Forewordiii 1Scope1 2Normative re
23、ferences1 3Designation system1 4Examples of designations5 Annex ZA (normative) Normative references to international publications with their relevant European publicationsInside back cover Table 1 Code-letters used for additional information in data block 12 Table 2 Code-letters used in data block 2
24、3 Table 3 Ranges of Vicat softening temperature in data block 33 Table 4 Ranges of melt flow rate in data block 34 Table 5 Ranges of Izod impact strength in data block 34 Table 6 Ranges of flexural modulus in data block 34 Table 7 Code-letters for fillers and reinforcing materials in data block 45 L
25、icensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10366-1:1993(E) BSI 04-2000iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of prepa
26、ring International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in l
27、iaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publica
28、tion as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10366-1 was prepared by Technical Committee ISO/TC 61, Plastics, Sub-Committee SC 9, Thermoplastic materials. ISO 10366 consists of the following parts, under the gene
29、ral title Plastics Methyl methacrylate/acrylonitrile/butadiene/styrene (MABS) moulding and extrusion materials: Part 1: Designation system and basis for specifications; Part 2: Preparation of test specimens and determination of properties. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23
30、:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 10366-1:1993(E) BSI 04-20001 1 Scope 1.1 This part of ISO 10366 establishes a system of designation for MABS thermoplastic material,
31、which may be used as the basis for specifications. 1.2 The types of MABS plastics are differentiated from each other by a classification system based on appropriate levels of the designatory properties a) Vicat softening temperature b) melt flow rate c) impact strength d) flexural modulus and on inf
32、ormation about basic polymer parameters, intended application and/or method of processing, important properties, additives, colorants, fillers and reinforcing materials. 1.3 This part of ISO 10366 is applicable to all transparent methyl methacrylate/acrylonitrile/butadiene/styrene thermoplastic mate
33、rials comprised of a continuous phase consisting of polymers of styrene (and/or an alkyl-substituted styrene), acrylonitrile and poly(methyl methacrylate), and a dispersed elastomeric phase based on butadiene. It applies to materials ready for normal use in the form of powder, granules or pellets an
34、d to materials unmodified or modified by colorants, additives, fillers, etc. 1.4 It is not intended to imply that materials having the same designation give necessarily the same performance. This part of ISO 10366 does not provide engineering data, performance data or data on processing conditions w
35、hich may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods specified in part 2 of this International Standard, if suitable. 1.5 In order to specify a the
36、rmoplastic material for a particular application or to ensure reproducible processing, additional requirements may be given in data block 5 (see clause 3, introductory paragraph). 2 Normative references The following standards contain provisions which, through reference in this text, constitute prov
37、isions of this part of ISO 10366. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this part of ISO 10366 are encouraged to investigate the possibility of applying the most recent editions of the standards indica
38、ted below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 1043-1:1987, Plastics Symbols Part 1: Basic polymers and their special characteristics. ISO 1133:1991, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of t
39、hermoplastics. ISO 10366-2:, Plastics Methyl methacrylate/acrylonitrile/butadiene/styrene (MABS) moulding and extrusion materials Part 2: Preparation of test specimens and determination of properties1). 3 Designation system The designation system for thermoplastics is based on the following standard
40、ized pattern: 1) To be published. Designation Description block (optional) Identity block International Standard Number block Individual-item block Data block 1 Data block 2 Data block 3 Data block 4 Data block 5 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontr
41、olled Copy, (c) BSI ISO 10366-1:1993(E) 2 BSI 04-2000 The designation consists of an optional description block, reading “Thermoplastics”, and an identity block comprising the International Standard number and an individual-item block. For unambiguous coding, the individual-item block is subdivided
42、into 5 data blocks comprising the following information: The first character of the individual-item block shall be a hyphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by doubling the separation sign, i.e. by two commas (,). 3.1
43、 Data block 1 In this data block, after the hyphen, methyl methacrylate/acrylonitrile/butadiene/styrene plastics are identified by the symbol “MABS”, in accordance with ISO 1043-1, followed by a hyphen and a single code-letter, giving additional information on the polymer as specified in Table 1. Ta
44、ble 1 Code-letters used for additional information in data block 1 The AN content of the continuous phase shall be determined in accordance with ISO 10366-2:2), Annex A. The MMA content of the compound shall be determined by analysis of the oxygen content. 3.2 Data block 2 In this data block, inform
45、ation about intended application and/or method of processing is given in position 1 and information about important properties, additives and colour in positions 2 to 8. The code-letters used are specified in Table 2. If information is presented in positions 2 to 8 and no specific information is giv
46、en in position 1, the letter X shall be inserted in position 1. Data block 1: Identification of the plastic by its symbol MABS in accordance with ISO 1043-1 and information about the polymerisation process or composition of the polymer (see 3.1). Data block 2: Position 1: Intended application or met
47、hod of processing (see 3.2). Positions 2 to 8: Important properties, additives and supplementary information (see 3.2). Data block 3: Designatory properties (see 3.3). Data block 4: Fillers or reinforcing materials and their nominal content (see 3.4). Data block 5: For the purpose of specifications,
48、 a fifth data block may be added containing additional information. Code-letter Range of AN content % (m/m) Range of MMA content % (m/m) A B C D 10 but u50 50 but u 80 10 but u 50 50 2) To be published. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:23:14 GMT+00:00 2006, Uncontrolled Copy
49、, (c) BSI ISO 10366-1:1993(E) BSI 04-20003 Table 2 Code-letters used in data block 2 3.3 Data block 3 In this data block, the range of the Vicat softening temperature is represented by a 3-figure code-number (see 3.3.1), the range of the melt flow rate by a 2-figure code-number (see 3.3.2), the range of the impact strength by a 2-figure code-number (see 3.3.3) and the range of the flexural modulus by a 2-figure code-number (see 3.3.4). The code-numbers are separated from each other by hyphen