《BS-EN-ISO-10472-3-1998.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-10472-3-1998.pdf（20页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 10472-3:1998 Incorporating Corrigendum No. 1 Safety requirements for industrial laundry machinery Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997) The European Standard EN ISO 10472-3:1997 has the status of a British Standard ICS 97.060 Licensed
2、 Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10472-3:1998 This British Standard, having been prepared under the direction of the Sector Board for Materials and Chemicals, was published under the authority of the Standards Board and come
3、s into effect on 15 March 1998 BSI 05-1999 ISBN 0 580 29396 3 National foreword This British Standard is the English language version of EN ISO 10472-3:1997. It is identical with ISO 10472-3:1997. The UK participation in its preparation was entrusted to Technical Committee TCI/33 Textile machinery,
4、which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate
5、them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally include an annex which lists normative references to international publications with their corresp
6、onding European publications The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Find” facility of the BSI Standards Electronic Catal
7、ogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comp
8、rises a front cover, an inside front cover, pages i and ii, the EN ISO title page, page 2, the ISO title page, pages ii to iv, pages 1 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in
9、the amendment table on the inside front cover. Amendments issued since publication Amd. No.DateComments 10224 Corrigendum January 1999 Indicated by a sideline in the margin Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10472-3:19
10、98 BSI 05-1999i Contents Page National forewordInside front cover Foreword2 Forewordiii Text of ISO 10472-31 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ii blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2
11、006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10472-3 December 1997 ICS 97.060 Descriptors: See ISO document English version Safety requirements for industrial laundry machinery Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997) Ex
12、igences de scurit pour les machines de blanchisserie industrielle Partie 3: Trains de lavage incluant les machines composantes (ISO 10472-3:1997) Sicherheitsanforderungen fr industrielle Wschereimaschinen Teil 3: Durchlaufwaschanlagen einschlielich Einzelmaschinen (ISO 10472-3:1997) This European St
13、andard was approved by CEN on 21 December 1997. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concern
14、ing such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own la
15、nguage and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden
16、, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Mem
17、bers. Ref. No. EN ISO 10472-3:1997 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10472-3:1997 BSI 05-1999 2 Foreword The text of the International Standard ISO 10472-3:1997 has been prepared by Technical Committee ISO/TC 72 “Texti
18、le machinery and machinery for dry-cleaning and industrial laundering” in collaboration with Technical Committee CEN/TC 214 “Textile machinery and machinery for dry-cleaning and industrial laundry”, the secretariat of which is held by SNV. This European Standard has been prepared under a mandate giv
19、en to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZB, which is an integral part of this standard. According to the CEN/CENELEC Internal Regulations, the na
20、tional standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
21、 Endorsement notice The text of the International Standard ISO 10472-3:1997 was approved by CEN as a European Standard without any modification. NOTENormative references to International Standards are listed in Annex ZA (normative). Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT
22、+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10472-3:1997 ii BSI 05-1999 Contents Page Forewordiii Introduction 1 1Scope1 2Normative references1 3Definitions2 4Hazards2 5Safety requirements a
23、nd/or measures for the hazards identified in clause 43 5.1General3 5.2Mechanical hazards3 5.2.1Interface between loading system and continuous tunnel washing machine3 5.2.2Continuous tunnel washing machine3 5.2.3Conveyors between washing machine and squeeze press or centrifugal extraction machine3 5
24、.2.4Squeeze press4 5.2.5Centrifugal extraction machine4 5.2.6Transfer conveyor system4 5.2.7Automatic transfer tumbler dryers4 5.2.8Interface between tumbler dryers and unloading system4 5.3Electrical hazards5 5.4Thermal hazards5 5.5Hazards generated by noise5 5.6Hazards associated with materials an
25、d substances5 5.6.1Fire and explosion5 5.6.2Biological hazards5 5.7Failure of control systems5 5.8Hazards associated with complex installations5 6Verification of safety requirements and/or measures5 7Information concerning machine use8 7.1Instruction handbook8 7.2Warning signs8 Annex ZA (normative)
26、Normative references to international publications with their relevant European publicationsInside back cover Annex ZB (informative) Relationship of this European Standard with EU DirectivesInside back cover Figure 1 Sensing device for out-of-balance condition4 Table 1 List of verifications6 Descrip
27、tors: Laundries, industrial facilities, textile machinery, laundering machines, washing tunnel, hazards, accident prevention, safety of machines, specifications, safety requirements, safety measures, verification, marking, instructions, instructions for use Licensed Copy: sheffieldun sheffieldun, na
28、, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10472-3:1997 BSI 05-1999iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally
29、carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the wo
30、rk. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard require
31、s approval by at least 75 % of the member bodies casting a vote. International Standard ISO 10472-3 was prepared by Technical Committee ISO/TC 72, Textile machinery and machinery for dry-cleaning and industrial laundering, Subcommittee SC 5, Industrial laundry and dry-cleaning machinery. ISO 10472 c
32、onsists of the following parts, under the general title Safety requirements for industrial laundry machinery: Part 1: Common requirements; Part 2: Washing machines and washer-extractors; Part 3: Washing tunnel lines including component machines; Part 4: Air dryers; Part 5: Flatwork ironers, feeders
33、and folders; Part 6: Ironing and fusing presses. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10472-3:1997 BSI 05-1
34、9991 Introduction This part of ISO 10472 is intended to instruct the designer of industrial laundry machinery in a systematic manner, focusing on his particular type of machine, regarding the relevant essential safety requirements, and to suggest possible state-of-the-art safety solutions. The exten
35、t to which hazards are covered is indicated in the scope of this part of ISO 10472. In addition, machinery should comply as appropriate with ISO/TR 12100-1 and ISO/TR 12100-2 for hazards which are not specifically referred to in this part of ISO 10472. All examples given in this part of ISO 10472 re
36、present the state of the art. Equivalent solutions are acceptable, provided they attain at least the same safety level. The designer is presumed to have taken into account all the provisions of ISO 10472-1 before considering this part of ISO 10472. 1 Scope This part of ISO 10472 covers, together wit
37、h ISO 10472-1, most significant hazards associated with washing tunnel lines including component machines such as: continuous tunnel washing machines; squeeze presses or centrifugal extraction machines; transfer conveyor systems; automatic transfer tumblers; loading or unloading system interfaces; a
38、ccess platform and ladders. This part of ISO 10472 does not cover particular hazards for continuous stand-alone washing lines for endless towels. This part of ISO 10472 does not cover the hazards caused by processing work which may create an explosive or flammable atmosphere inside the machine. This
39、 part of ISO 10472 complements the basic requirements laid down in ISO/TR 12100-1 and ISO/TR 12100-2. It also gives guidance to the designer on assessing the risks associated with the hazards (see EN 1050) and on selecting measures for attaining the required safety level. This part of ISO 10472 does
40、 not apply to ancillary equipment, e.g. chemical store and supply pumps, steam valves and supply pipework, vent systems, work feed systems and discharge systems and ducting to the atmosphere. 2 Normative references The following standards contain provisions which, through reference in this text, con
41、stitute provisions of this part of ISO 10472. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreement based on this part of ISO 10472 are encouraged to investigate the possibility of applying the most recent editions of the stand
42、ards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 6182-1:1993, Fire protection Automatic sprinkler systems Part 1: Requirements and test methods for sprinklers. ISO 10472-1:1997, Safety requirements for industrial laundry machinery Part 1
43、: Common requirements. ISO/TR 12100-1:1992, Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology. ISO/TR 12100-2:1992, Safety of machinery Basic concepts, general principles for design Part 2: Technical principles and specifications. ISO 13849-1:,
44、Safety of machinery Safety-related parts of control systems Part 1: General principles for design1). ISO 13852:1996, Safety of machinery Safety distances to prevent danger zones being reached by the upper limbs. ISO 14119:, Safety of machinery Interlocking devices associated with guards Principles f
45、or design and selection1) . EN 616:, Continuous handling equipment and systems Common safety requirements for design, manufacturing, erection and commissioning stages1). EN 620:, Continuous handling equipment and systems Equipment for mechanical handling both unit loads and bulk materials Special sa
46、fety requirements for design, manufacturing, erection and commissioning stages.1). EN 746-2:1997, Industrial thermoprocessing equipment Part 2: Safety requirements for combustion and fuel handling systems. EN 953:1997, Safety of machinery General requirements for the design and construction of guard
47、s (fixed, movable). EN 1037:1995, Safety of machinery Prevention of unexpected start-up. EN 1050:1996, Safety of machinery Risk assessment. 1) To be published. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 03:12:06 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10472-3:1997 2 BSI 05-1999
48、 EN 1760-1:1997, Safety of machinery Pressure sensitive protective devices Part 1: General principles for the design and testing of pressure sensing mats and floors. EN 1760-2:, Safety of machinery Pressure sensitive protective devices Part 2: General principles for the design and testing of pressur
49、e sensitive edges and pressure sensitive bars2). EN 50100-1:, Safety of machinery Electro-sensitive protective devices Part 1: General requirements and tests2). EN 60204-1:1992, Safety of machinery Electrical equipment of machines Part 1: General requirements. IEC 204-1:1992, modified. 3 Definitions For the purposes of this part of ISO 10472, the following definitions apply: 3.1 washing tunnel line complete integrated system of linked machines for the washing, mo