《BS-ISO-IEC-15434-2006.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-IEC-15434-2006.pdf（26页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO/IEC 15434:2006 Information technology Automatic identification and data capture techniques Syntax for high-capacity ADC media ICS 35.040 ? Licensed Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI
2、 BS ISO/IEC 15434:2006 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 December 2006 BSI 2006 ISBN 0 580 49857 3 National foreword This British Standard was published by BSI. It is the UK implementation of ISO/IEC 15434:2006. It supersedes
3、 BS ISO/IEC 15434:2005 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee IST/34, Automatic identification and data capture techniques. A list of organizations represented on IST/34 can be obtained on request to its secretary. This publication does not p
4、urport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Amendments issued since publication Amd. No. DateComments Licensed Copy: London South Bank University, Lo
5、ndon South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI Reference number ISO/IEC 15434:2006(E) INTERNATIONAL STANDARD ISO/IEC 15434 Third edition 2006-10-01 Information technology Automatic identification and data capture techniques Syntax for high-capacity ADC med
6、ia Technologies de linformation Techniques didentification et captage automatique des donnes Syntaxe pour supports de CAD haute capacit BS ISO/IEC 15434:2006 Licensed Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI ii L
7、icensed Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iii Contents Page Foreword iv Introduction v 1 Scope 1 2 Normative references1 3 Terms, definitions and documentation notation conventions2 3.1 Terms and definitio
8、ns .2 3.2 Documentation notation conventions.2 4 Message format2 4.1 Message Envelope.3 4.1.1 Message Header.3 4.1.2 Message Trailer4 4.2 Format Envelope4 4.2.1 Format Header4 4.2.2 Format Header “00” - Reserved format.6 4.2.3 Format Header “01” - Transportation6 4.2.4 Format Header “02” - Complete
9、EDI message / transaction.6 4.2.5 Format Header “03” - Structured data using ASC X12 segments 6 4.2.6 Format Header “04” - Structured data using UN/EDIFACT segments .7 4.2.7 Format Header “05” - Data using GS1 Application Identifiers7 4.2.8 Format Header “06” - Data using ASC MH 10 Data Identifiers7
10、 4.2.9 Format Header “07” - Free form text data.8 4.2.10 Format Header “08” - Structured data using CII syntax rules 8 4.2.11 Format Header “09” - Binary data8 4.2.12 Format Header (“10”- “11”) - Reserved formats.8 4.2.13 Format Header “12” - Data using Text Element Identifiers .9 4.2.14 Format Head
11、er (“13”-“99”) - Reserved formats9 4.2.15 Format Trailer.9 4.3 Data format.9 4.3.1 Format “00” (Reserved) 9 4.3.2 Format “01” Carrier sortation and tracking (Transportation) .10 4.3.3 Format “02” (Complete EDI message / transaction)12 4.3.4 Format “03” (Structured data using ASC X12 segments) .12 4.
12、3.5 Format “04” (Structured data using UN/EDIFACT segments) 12 4.3.6 Format “05” (Using GS1 Application Identifiers) .13 4.3.7 Format “06” (Using ASC MH 10 Data Identifiers).13 4.3.8 Format “07” (Free form text format) 13 4.3.9 Format “08” (Structured data using CII syntax rules)13 4.3.10 Format “09
13、” (Binary data).13 4.3.11 Format “10”-“11” (Reserved)14 4.3.12 Format “12” (Using Text Element Identifiers).14 4.3.13 Format “13”-“99” (Reserved)14 5 Maintenance.14 Annex A (normative) Subset of ISO 646 (Table of hexadecimal and decimal values).16 Bibliography17 BS ISO/IEC 15434:2006 Licensed Copy:
14、London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI iv Foreword ISO (the International Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardiz
15、ation. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees established by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutu
16、al interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the field of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. International Standards are drafted in accordan
17、ce with the rules given in the ISO/IEC Directives, Part 2. The main task of the joint technical committee is to prepare International Standards. Draft International Standards adopted by the joint technical committee are circulated to national bodies for voting. Publication as an International Standa
18、rd requires approval by at least 75 % of the national bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO and IEC shall not be held responsible for identifying any or all such patent rights. ISO/IEC 15434 wa
19、s prepared by Joint Technical Committee ISO/IEC JTC 1, Information technology, Subcommittee SC 31, Automatic identification and data capture techniques. This third edition cancels and replaces the second edition (ISO/IEC 15434:2005), which has been technically revised. BS ISO/IEC 15434:2006 Licensed
20、 Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI v Introduction This International Standard defines the manner in which data is transferred to high-capacity automatic data capture (ADC) media from a suppliers informatio
21、n system and the manner in which data is transferred to the recipients information system. This International Standard does not define the internal data storage format for specific high-capacity ADC media. This International Standard does not specify the application of data structures provided by a
22、specific data syntax format. The application of the data structure is specified by industry conventions. Users of ADC technologies benefit by being able to receive data in a standard form and by being able to provide data in a standard form. Static ADC technologies such as bar code symbologies, magn
23、etic stripe, optical character recognition, surface acoustical wave (SAW) and Weigand effect typically encode a single field of data. Most applications of these technologies involve the encoding of a single field of data by the supplier of the medium and the subsequent decoding of the data field by
24、the recipient. Encoding single fields of data permits the supplier to perform the encodation from a single field within the suppliers information system. Decoding single fields of data permits the recipient to input this data into a single field in the recipients information system, in lieu of key e
25、ntry. High-capacity ADC technologies, such as two-dimensional symbols, RFID transponders, contact memories and smart cards, encode multiple fields of data. These multiple fields are usually parsed by the recipients information system and then mapped to specific fields of data in the recipients infor
26、mation system. This International Standard defines the syntax for high-capacity ADC media, so as to enable ADC users to utilize a single mapping utility, regardless of which high-capacity ADC medium is employed. BS ISO/IEC 15434:2006 Licensed Copy: London South Bank University, London South Bank Uni
27、versity, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI blank Licensed Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 1 Information technology Automatic identification and data capture techniques Syntax
28、 for high-capacity ADC media 1 Scope This International Standard specifies a transfer structure, syntax, and coding of messages and data formats when using high-capacity ADC media between trading partners (specifically between suppliers and recipients) and, where applicable, in support of carrier ap
29、plications, such as bills of lading, and carrier sortation and tracking. The data encoded according to this International Standard include data which may be used in the shipping, receiving and inventory of transport units; data which may be contained within supporting documentation, in paper or elec
30、tronic form, related to unit loads or transport packages; data which may be used in the sortation and tracking of transport units. This International Standard describes the ISO 646 syntax for automatic data capture. This International Standard is not the controlling specification for data structures
31、 (e.g. CII) referenced in this International Standard. This International Standard does not supersede or replace any applicable safety or regulatory marking or labelling requirements. This International Standard is to be applied in addition to any other mandated labelling requirements. 2 Normative r
32、eferences The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 646, Information technology ISO
33、 7-bit coded character set for information interchange ISO/IEC 19762 (all parts), Information technology Automatic identification and data capture (AIDC) techniques Harmonized vocabulary ANS MH10.8.2, ASC MH 10 Data Identifiers and Application Identifiers ANS MH10.8.3, ASC MH 10 Syntax for high capa
34、city ADC media ANS X12, Electronic Data Interchange CII Syntax Rule (Vers 3.00), CII Syntax Rule Specifications (3.00) (Electronic Data Interchange Japan) GS1 General Specification, GS1 ATA Common Support Data Dictionary (CSDD), Air Transport Association BS ISO/IEC 15434:2006 Licensed Copy: London S
35、outh Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 2 3 Terms, definitions and documentation notation conventions 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in ISO/IEC 19762 (all parts) a
36、pply. 3.2 Documentation notation conventions This International Standard uses the following typographical conventions in message examples. a) BOLD, ALL CAPITALS Text that must be entered exactly as it appears. (In this International Standard, FS, GS, US, RS, EOT are used to represent non-printable s
37、pecial characters. The ISO 646 representation of special characters used in this International Standard can be found in Annex A.) b) italic, lower case Variable Parameters. The user must supply an appropriate value. In some cases default values are recommended in this International Standard. 4 Messa
38、ge format This clause defines how data shall be transferred from a High Capacity ADC Media reading device to the users application software. To allow multiple data Formats to be contained within a data stream, a two level structure of enveloping is employed. The outermost layer of the message is a M
39、essage Envelope that defines the beginning and end of the message. Within the Message Envelope are one or more Format Envelopes that contain the data (see Figure 1). Multiple formats in a single message should only be employed with bi-lateral agreements of the trading partners. The Message Envelope
40、shall consist of a Message Header, one or more Format Envelope(s), and a Message Trailer (when required). Each Format Envelope within the Message Envelope shall consist of a Format Header, data, formatted according to the rules defined for that Format, and a Format Trailer (when required). BS ISO/IE
41、C 15434:2006 Licensed Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 3 Figure 1 Enveloping Structure Note: Annex A shows the decimal and hexadecimal values of ASCII characters used in this International Standard. 4.1 M
42、essage Envelope The Message Envelope defines the start and end of the data contained within the data stream, and provides the following functions: indication that the message contained within this media is formatted in compliance with the rules of this International Standard; indicates the character
43、 which has been defined to separate Formats within this Message; provides a unique character to indicate the end of the Message. The structure within a data stream is as follows: a Message, containing one or more Formats; a Format, containing one or more Segments; a Segment, containing one or more D
44、ata Elements; a Data Element (Field), potentially containing one or more Sub-elements (Sub-fields). 4.1.1 Message Header The Message Header consists of two parts: the three character Compliance Indicator, and the Format Trailer Character. The complete Message Header1) is: )RS 1) An artificial “space
45、” character has been added between the “” and “)” characters so as to not be misinterpreted as the alphabetic character “D”. BS ISO/IEC 15434:2006 Licensed Copy: London South Bank University, London South Bank University, Wed Jan 10 01:42:40 GMT+00:00 2007, Uncontrolled Copy, (c) BSI 4 4.1.1.1 Compl
46、iance Indicator The Compliance Indicator shall be the first three characters in the Message Header. The Compliance Indicator shall be ) (left bracket, right parenthesis, and greater than). See Annex A for a table of ASCII decimal and hexadecimal values used in this International Standard. 4.1.1.2 Fo
47、rmat Trailer Character The Format Trailer Character shall be the fourth character in the Message Header. The Format Trailer Character shall be the non-printable ASCII character “RS” (see Annex A). The Format Trailer Character is used throughout the message to indicate the end of a data Format envelo
48、pe (see 4.2.15). 4.1.2 Message Trailer The Message Trailer identifies the end of the message within the data stream. The Message Trailer shall be the End Of Transaction character, “EOT” (see Annex A). The Message Trailer character shall not be used elsewhere in the message except in Format “09” (bin
49、ary data) where the “EOT” character may appear. The Message Trailer shall not be used with Formats “02” (Complete EDI message / transaction) and “08” (Structured data using CII Syntax Rules). 4.2 Format Envelope The Format Envelope defines the start and end of data in a given Format and provides the following functions: identifies the data Format used within the envelope; defines the character(s) used to separate the Segments, Data Elements (Fiel