《BS-ISO-TR-10193-1989.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-TR-10193-1989.pdf（22页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO TR 10193:1989 Implementation of ISO TR 10193:1989 Round general use light gauge metal containers Nominal filling volumes and nominal diameters UDC 621.798.144-034 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO
2、 TR 10193:1989 This British Standard, having been prepared under the direction of the Consumer Products and Services Sector Board, was published under the authority of the Standards Board and comes into effect on 15 January 1996 BSI 01-2000 The following BSI references relate to the work on this sta
3、ndard: Committee reference PKW/2 Draft announced in BSI News June 1995 ISBN 0 580 25305 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted to Technical Committee PKW/2, Primary packaging, upon which the following bodies were represented: Associa
4、tion of the British Pharmaceutical Industry British Aerosol Manufacturers Association British Fibreboard Packaging Association British Glass Manufacturers Confederation British Plastics Federation British Retail Consortium Chemical Industries Association Cosmetic, Toiletry and Perfumery Association
5、Limited Department of Trade and Industry (Consumer Safety Unit, CA Division) Department of Trade and Industry (Laboratory of the Government Chemist) Environmental and Technical Association for the Paper Sack Industry Flexible Packaging Association Institute of Packaging Institute of Trading Standard
6、s Administration Institute of Wastes Management Metal Packaging Manufacturers Association Packaging and Industrial Films Association Paper Federation of Great Britain Pira International The following bodies were also represented in the drafting of the standard, through subcommittees and panels: Brit
7、ish Coatings Federation Ltd. British Compressed Gases Association Consumer Policy Committee of BSI Engineering Equipment and Materials Users Association Health and Safety Executive LP Gas Association Society of Cosmetic Scientists Amendments issued since publication Amd. No.DateComments Licensed Cop
8、y: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO TR 10193:1989 BSI 01-2000i Contents Page Committees responsibleInside front cover National forewordii Forewordiii Text of ISO TR 101931 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:3
9、3 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO TR 10193:1989 ii BSI 01-2000 National foreword This British Standard reproduces verbatim ISO TR 10193:1989 and implements it as the UK national standard. This British Standard is published under the direction of the Consumer Products and Services S
10、ector Board whose Technical Committee PKW/2 has the responsibility to: aid enquirers to understand the text; present to the responsible international committee any enquiries on interpretation, or proposals for change, and keep UK interests informed; monitor related international and European develop
11、ments and promulgate them in the UK. NOTEInternational and European Standards, as well as overseas standards, are available from Customer Services, BSI, 389 Chiswick High Road, London W4 4AL. A British Standard does not purport to include all the necessary provisions of a contract. Users of British
12、Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the ISO TR title page, pages ii to iv, pages 1 to 12 a
13、nd a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed
14、Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) ii BSI 01-2000 Contents Page Forewordiii Introduction1 1Scope1 2Reference1 3Designation of containers (types and construction)1 4Characteristics1 5Current list of nominal filling v
15、olumes and nominal diameters1 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-2000iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
16、member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, govern
17、mental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The main task of ISO technical committees is to prepare International Standards. In exce
18、ptional circumstances a technical committee may propose the publication of a technical report of one of the following types: type 1, when the necessary support within the technical committee cannot be obtained for the publication of an International Standard, despite repeated efforts; type 2, when t
19、he subject is still under technical development requiring wider exposure; type 3, when a technical committee has collected data of a different kind from that which is normally published as an International Standard (“state of the art”, for example). Technical reports are accepted for publication dir
20、ectly by ISO Council. Technical reports of types 1 and 2 are subject to review within three years of publication, to decide whether they can be transformed into International Standards. Technical reports of type 3 do not necessarily have to be reviewed until the data they provide are considered to b
21、e no longer valid or useful. ISO/TR 10193, which is a technical report of type 3, was prepared by Technical Committee ISO/TC 52, Light gauge metal containers. Data of a similar nature to those presented in this Technical Report, but for non-round containers, are given in ISO/TR 10194:1989, Non-round
22、 general use light gauge metal containers Nominal filling volumes and nominal cross-sections. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontroll
23、ed Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-20001 Introduction This Technical Report presents the results of a survey on the sizes of different types of round general use light gauge metal containers in current use. The way in which these data can be reduced sufficiently to establish an Internatio
24、nal Standard is under consideration. 1 Scope This Technical Report gives a current list of nominal filling volumes and related nominal diameters for round general use light gauge metal containers. 2 Reference ISO 90-2:1986, Light gauge metal containers Definitions and determination methods for dimen
25、sions and capacities Part 2: General use containers. 3 Designation of containers (types and construction) The definitions, designations and special features of these types of containers (necked-in and/or step-sided) are given in ISO 90-2. This Technical Report concerns the following containers: full
26、 friction can, cylindrical; full friction can, tapered; friction closure can, cylindrical; friction closure can, tapered; slip cover can, cylindrical; slip cover can, tapered; flat top can, cylindrical; flat top can, tapered; cone top can, cylindrical. 4 Characteristics 4.1 Nominal diameters: tolera
27、nces Tolerances on the diameters at the top end and at the bottom end are the following: diameter u 155 mm: 2 mm diameter 155 mm: 3 mm 4.2 Head spaces and nominal filling volumes: special case of the transport of dangerous goods With regard to head spaces required for the transport of dangerous good
28、s, reference has to be made to valid regulations. 5 Current list of nominal filling volumes and nominal diameters For each type of container mentioned in clause 3, the following are given: a figure showing the type of container; a table giving values of nominal filling volumes and of nominal diamete
29、rs. Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) 2 BSI 01-2000 5.1 Full friction can, cylindrical Nominal filling volumes Nominal diameters mm mlDDN2Ds 100 52 55 125 52 55 60 250 65 73 99 375 73 83 99 500 83 99 105 1
30、08 750 99 108 1 000 99 108 140 2 000 140 140 153 160 160 200 135 147 153 187 2 500 140 153 160 165 200 135 147 187 3 000 153 160 160 160 165 200 147 153 187 Nominal filling volumes Nominal diameters mm mlDDN2Ds 4 000 153 160 160 160 180 180 200 147 153 173 187 5 000 180 180 180 200 165 173 187 10 00
31、0 220 230 230 240 225 11 500 230 230 225 12 500 220 230 15 000 230 305295 17 500305295 20 000 280 280 305 274 295 25 000 280 300 305295 27 000300 28 000 328 328322 30 000 300 305 328 328 295 322 40 000 305 328 295 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncont
32、rolled Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-20003 5.2 Full friction can, tapered Nominal filling volumes Nominal diameters mm mlD1D2DN2Ds 1 000140130 2 000160148 2 500 160 160 165 190 148 153 175 148 3 000 160 160 160 165 165 180 180 148 150 153 165 171 148 148 155 168 4 000 160 180 180 180 18
33、0 200 200 148 168 165 171 185 190 168 5 000 180 180 180 165*) 180 185 195 195 200 200 168 165 171 175 180 185 190 168 188*) 185 Nominal filling volumes Nominal diameters mm mlD1D2DN2Ds 10 000 220 230 230 230 230 240 240 240 275 286 205 220 217 216 225 230 255 212 216 271 11 500 230 230217 216 12 500
34、 220 230 230 240 275 286 286 205 217 225 255 268 216 271 13 500 240 286 292 225 275 271 15 000 230 275 286 286 292 305 305 220 255 271 275 286 271 290 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) 4 BSI 01-2000 Nomina
35、l filling volumes Nominal diameters mm mlD1D2DN2Ds 17 500 275 286 286 292 305 305 255 271 275 286 271 290 20 000 275 280 286 286 286 292 305 305 305 255 265 271 268 275 286 271 286 290 22 000 292 305 275 286 25 000 286 286 286 292 305 305 305 268 271 275 286 271 286 290 27 000 286 292 305 275 286 27
36、1 28 000 292 305 328 275 286 312 30 000 286 286 292 305 305 305 328 271 275 286 312 271 286 290 40 000 305 305 380 286 360 290 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-20005 5.3 Friction closure can, cylin
37、drical Nominal filling volumes Nominal diameters mm mlDDN2Ds 5045 100 55 60 65 11863 125 52 55 60 65 69 236 69 73 250 69 73 99 375 73 83 86 95 99 500 73 83 86 90 95 99 108 750 99 108 946105 1 000 99 108 114 127 140 2 000 127 140 153 160 Nominal filling volumes Nominal diameters mm mlDDN2Ds 2 500 140
38、 153 160 165 171 3 000 153 160 165 4 000 153 160 165 171 175 180 5 000 165 171 175 195 180 10 000 216 220 225 230 240 11 500 230 240 12 500230 13 500240 15 000240 20 000 280 292 25 000 292 280 300 28 000 292 300 328 30 000 292 300 328 40 000328 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26
39、15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) 6 BSI 01-2000 5.4 Friction closure can, tapered Nominal filling volumes Nominal diameters mm mlDN2D2Ds 2 000148166 2 500148 153 148 168 168 166 3 000 148 148 168 166 4 000 168 168 180 148 168 171 166 190 188 190 195 205 5 000
40、168 168 180 168 171 185 188 190 190 195 200 205 10 000216240 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-20007 5.5 Slip cover can, cylindrical Nominal filling volumes ml Nominal diameters D mm 50 45 73 7590 1
41、00 55 69 90 125 55 69 78 150108 200 65 69 73 108 250 55 73 90 95 99 108 375 73 83 90 99 500 73 78 83 90 95 99 108 120 750 73 78 83 86 99 114 1 000 99 108 114 120 127 130 Nominal filling volumes ml Nominal diameters D mm 1 500 108 114 127 130 140 2 000 120 130 140 153 160 175 2 500 130 140 153 160 16
42、3 180 3 000 153 160 163 180 251 4 000 153 160 163 180 195 251 5 000 153 160 175 180 190 195 216 230 10 000 195 220 230 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) 8 BSI 01-2000 5.6 Slip cover can, tapered 5.7 Flat t
43、op can, cylindrical Nominal filling volumes ml Nominal diameters mm D1D2Ds 1 000140130 2 500 190175 153168 3 000190175 5 000216230 Nominal filling volumes ml Nominal diameters mm DDN1DN2 100 52 55 65 125 52 55 60 65 250 52 55 65 73 83 375 73 83 99 500 65 73 78 83 86 99 Nominal filling volumes ml Nom
44、inal diameters mm DDN1DN2 750 73 78 99 1 000 73 78 83 86 90 99 108 1 500 86 127 140 2 000 127 140 153 165 2 500 140 140 140 153 165 135 135 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-20009 Nominal filling vo
45、lumes ml Nominal diameters mm DDN1DN2 3 000 153 160 160 165 155 4 000 153 160 165 175 5 000 153 160 160 165 171 175 180 185 195 230 155 155 10 000 216 220 220 220 225 230 240 280 212 212 11 500 230 230 230 240 225 225 12 500230 13 500 230 240 15 000 240 286 286 305 278 295 17 500 286 305 Nominal fil
46、ling volumes ml Nominal diameters mm DDN1DN2 20 000 230 280 280 280 286 286 305 305 314 273 278 295 273 25 000 280 280 286 286 292 300 305 305 273 278 295 27 000 286 292 300 328 28 000 300 328 328 322 322 30 000 286 286 300 305 314 328 328 328 278 295 322 322 40 000 328 360 360350 Licensed Copy: she
47、ffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) 10 BSI 01-2000 5.8 Flat top can, tapered Nominal filling volumes Nominal diameters mm mlD1D2DN1DN2 10 000 286 286271 271 15 000 286 286271 271 17 500 286 286271 271 20 000 286 288 305 286 3
48、05 286 271 271 25 000 286 286 305 305 286 305 286 300 271 271 30 000286 286271 271 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO/TR 10193:1989 (E) BSI 01-200011 5.9 Cone top can, cylindrical Nominal filling volumes ml Nominal diameters
49、 mm DDN1 100 52 55 125 52 55 60 65 23660 250 52 55 65 73 83 35565 375 73 83 99 47365 500 65 73 78 83 90 99 750 73 78 99 1 000 73 78 83 86 90 99 108 1 500 86 127 140 2 000 127 140 153 165 Nominal filling volumes ml Nominal diameters mm DDN1 2 500 140 153 165 3 000 153 160 165 4 000 153 160 165 175 5 000 153 160 165 171 175 180 195 230 10 000 216 220 220 230 280 240 286 212 11 500 230 240 12 500230 13 500 230 240 15 000 240 286 305 17 500 305 286 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 15:29:33 GMT+0