《BS-EN-ISO-14529-1-2000.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-14529-1-2000.pdf（16页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14529-1:2000 Th
2、e European Standard EN ISO 14529-1:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 1: Designation system and basis for specifications Licensed Copy: shef
3、fieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 Januar
4、y 2000 BSI 01-2000 ISBN 0 580 35882 8 BS EN ISO 14529-1:2000 Amendments issued since publication Amd. No.DateComments National foreword This British Standard is the English language version of EN ISO 14529-1:1999. It is identical with ISO 14529-1:1999. The UK participation in its preparation was ent
5、rusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK
6、 interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally inclu
7、de an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled International Standards
8、 Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does
9、 not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 6, page, an inside front cover and a back cover. The B
10、SI copyright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c
11、) BSI EN ISO 14529-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 14529-1:1999(E) INTERNATIONAL STANDARD ISO 14529-1 First edition 1999-11-15 Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 1:
12、 Designation system and basis for specifications Plastiques Poudres mouler base de mlamine/phnol (MP-PMC) Partie 1: Systme de dsignation et base de spcification EN ISO 14529-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI )E(9991:1-92
13、541OSI DPF dremialcsi ihTs PDF file may ctnoian emeddebd tyfepaces. In acconadrce with Aebods licnesing lopicy, this file may be pirtned or ivewed ubt slahl ton be ideted lnuess the tyfepaces which are emeddebd rae licnesed to nad instlaled on the comtuper freporming the idetign. In odwlnidaogn this
14、 feli, trapies cacpet tierehn the sersnoptilibiy of ont fnirnignig Aebods cilsnenig cilopy. hTe ISO tneCarl Sceteraairt cactpes no tilibaily in this .aera Abode is a tedarmrak of Abode Systems Inctaropro.de teDails of the sfotwrae pudorcts used to crtaee tihs PDF file can be fnuod in the Garenel Inf
15、o lerative to the file; the PD-Fcrtaeion arapmteres wree tpoimized for pirtnign. Evrey crae ahs eebn taken to nesrue taht the file is suitlbae for use by ISO memebr idobes. In teh lnuikley enevt taht a plborem lerating to it is fdnuo, lpaese ifnrom the tneCarl Secterairat at the erddass given lebow.
16、 ISO/IEC 9991 All rthgis resvrede. elnUss torehwise sepcfidei, no rapt of tihs ilbupctaoin may be udorperced or tuzilied in nay form or by nay mnaes, eelctcinor or mecinahcal, inclidung tohpociypong nad micrfoilm, wituoht repmission in writing form eitehr ISO at the erddass lebow or ISOs memebr ydob
17、 in the ctnuory of the reuqeste.r ISO cirypohgt fofice aCse opstale 56 ? 121-HC1 veneGa 20 leT. + 41 22 479 01 11 aFx + 41 22 374 10 97 E-mail cirypothgiso.ch Web www.iso.ch ii? EN ISO 14529-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c)
18、 BSI ISO -925411:(9991E) ?iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interes
19、ted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical C
20、ommission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication
21、as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 14529 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent
22、 rights. International Standard ISO 14529-1 was prepared by Technical Committee ISO/TC 61,Plastics, Subcommittee SC 12,Thermosetting materials. After a transition period of, at the most, four years, the three parts of ISO 14529 (see below) will replace ISO 4896:1990, of which they constitute a techn
23、ical revision. ISO 14529 consists of the following parts, under the general titlePlastics Melamine/phenolic powder moulding compounds (MP-PMCs): ?Part 1: Designation system and basis for specifications ?Part 2: Preparation of test specimens and determination of properties ?Part 3: Requirements for s
24、elected moulding compounds EN ISO 14529-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 14529-1:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STAND
25、ARDISO 14529-1:1999(E) ISO 9991 All irhgts seredevr1 Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 1: Designation system and basis for specifications 1Scope 1.1This part of ISO 14529 establishes a data block system for the designation of melamine/phenolic powder moulding compou
26、nds (MP-PMCs). 1.2The various types of MP-PMC are differentiated from each other by a classification system based on information about the filler/reinforcement type and content, the intended method of processing, any special properties and those of the special properties used specifically for design
27、ation purposes (designatory properties). 1.3This part of ISO 14529 is applicable to all MP-PMCs ready for normal use in the form of powder, granules or ground material. 1.4It is not intended to imply that materials having the same designation necessarily give the same performance. This part of ISO 1
28、4529 does not provide engineering data, performance data or data on processing conditions which may be required to specify a material for a particular application and/or method of processing. If such additional properties are required, they shall be determined in accordance with the test methods spe
29、cified in ISO 14529-2, if suitable. 1.5Whenever general requirement data, as covered by ISO 14529-3, need to be indicated, this is also done using this data block system. 1.6To ensure that code-letters and code-numbers remain unambiguous, and to avoid conflicts within the system, any new code-letter
30、s or code-numbers for use in data block 1, 2 or 3 shall be approved before use by the secretariats of ISO/TC 61/SC 1, SC 12 and SC 13. 2Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this part of ISO 14529. Fo
31、r dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 14529 are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For und
32、ated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 75-2:1993,Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite. ISO 179-1:1),Plastics De
33、termination of Charpy impact properties Part 1: Non-instrumented impact test. 1)To be published. (Revision of ISO 179:1993) EN ISO 14529-1:1999 1 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -925411:(9991E) 2 ISO 9991 All irhgts sered
34、evr ISO 472:1999,Plastics Vocabulary. ISO 1043-1:1997,Plastics Symbols and abbreviated terms Part 1: Basic polymers and their special characteristics. ISO 1043-2:2),Plastics Symbols and abbreviated terms Part 2: Fillers and reinforcing materials. ISO 4896:1990,Plastics Melamine/phenolic moulding mat
35、erials Specification. ISO 14529-2:1999,Plastics Melamine/phenolic powder moulding compounds (MP-PMCs) Part 2: Preparation of test specimens and determination of properties. ISO 14529-3:1999,PlasticsMelamine/phenolicpowdermouldingcompounds(MP-PMCs)Part 3: Requirements for selected moulding compounds.
36、 3Terms and definitions For the purposes of this part of ISO 14529, the terms and definitions given in ISO 472 and ISO 14529-2 apply, plus the following: 3.1 powder moulding compound powder, granules or ground material capable of flowing freely through the feed systems of processing machines, as wel
37、l as moulding compounds in the form of flakes which are normally not thought of as powders The abbreviation for powder moulding compound is PMC by analogy with bulk moulding compound (BMC) and sheet moulding compound (SMC). 3.2 MP-PMC abbreviation for powder moulding compounds based on melamine/phen
38、olic resins for both injection and compression moulding 3.3 melamine/phenolic resin synthetic resin obtained by reacting melamine and phenol with aldehydes, usually formaldehyde, the resin being formed either by co-condensation or as a physical mixture 4Designation system 4.1General The designation
39、system defined in this part of ISO 14529 is based on the following standardized pattern: Designation Identity block DescriptionISO Individual-item block blockStandard Data block 1 Data block 2 Data block 3 Data block 4 Data block 5 2)To be published. (Revision of ISO 1043-2:1988) EN ISO 14529-1:1999
40、 2 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -925411:(9991E) ISO 9991 All irhgts seredevr3 The designation consists of an optional description block, reading “PMC“, and an identity block comprising the International Standard number
41、 and an individual-item block. For unambiguous designation, the individual-item block is subdivided into five data blocks comprising the following information: Data block 1: Marking block Item 1: Identification of the basic polymer by its symbol, in accordance with ISO 1043-1; Item 2: Nature of the
42、designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 3: Form of the designatory reinforcement materials or fillers, in accordance with ISO 1043-2; Item 4: Nominal content of the designatory reinforcement materials or fillers, in accordance with Table 1. Data block 2: M
43、ethod of processing Method of processing for which the moulding compound is intended, designated in accordance with Table 2. Data block 3: Properties Item 1: Special properties, in accordance with Table 3; Item 2: Designatory property No. 1 impact strength determined in accordance with ISO 179-1; It
44、em 3: Designatory property No. 2 temperature resistance determined in accordance with ISO 75-2. Data block 4: Further information, taken from an international, national or company standard. Data block 5 (optional): Additional requirements The first character of the individual-item block shall be a h
45、yphen. The data blocks shall be separated from each other by commas. If a data block is not used, this shall be indicated by an “X“ (= not applicable), but only if another block follows. For labelling purposes, and provided no other blocks follow, the comma between blocks 1 and 2 can be omitted. The
46、re is no need to fill in data blocks if they are not required. 4.2Data block 1 Item 1: After the hyphen, melamine/phenolic powder moulding compounds shall be identified by the symbol MP, in accordance with ISO 1043-1. Mixtures and modifications shall be designated in accordance with ISO 1043-1:1997,
47、 subclauses 4 and 5. The following information shall be restricted to designatory fillers/reinforcements used in the material in question: Item 2: Nature of filler/reinforcement, in accordance with Table 1. Item 3: Form of filler/reinforcement, in accordance with Table 1. Item 4: Nominal content (ma
48、ss %) of filler/reinforcement, in accordance with Table 1. Note, in particular, the following: ?the same code-letters have different meanings when used for item 2 and item 3; ?whenever information needs to be indicated only for item 3, an “X“ ( = not applicable) is required for item 2. EN ISO 14529-
49、1:1999 3 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:45 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -925411:(9991E) 4 ISO 9991 All irhgts seredevr 4.3Data block 2 In this data block, information about the method of processing is given using the code-letters specified in Table 2. The code-letter used to indicate the intended method of processing in data block 2 shall be selected carefully. Certain brands of material can be processed in more