《BS-ISO-13950-2007.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-13950-2007.pdf（64页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 13950:2007 Incorporating corrigendum January 2008 Plastics pipes and fittings Automatic recognition systems for electrofusion joints ICS 23.040.20; 23.040.45 ? Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing C
2、o/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- BS ISO 13950:2007 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 April 2007 BSI 2008 ISBN 978 0 580 61746 1 Nationa
3、l foreword This British Standard is the UK implementation of ISO 13950:2007, incorporating corrigendum January 2008. The UK participation in its preparation was entrusted by Technical Committee PRI/88, Plastics piping systems, to Subcommittee PRI/88/2, Plastics piping for pressure applications. A li
4、st of organizations represented on this subcommittee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from
5、 legal obligations. Amendments/corrigenda issued since publication DateComments 30 April 2008Implementation of ISO corrigendum January 2008 (correcting paragraph 2 of 4.3.1) Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/59107700
6、01 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- Reference number ISO 13950:2007(E) INTERNATIONAL STANDARD ISO 13950 First edition 2007-03-15 Plastics pipes and fittings Automatic recognition systems for electrofusion joints Tubes et ra
7、ccords en matires plastiques Procds de reconnaissance automatique dun assemblage par lectrosoudage BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction
8、 or networking permitted without license from IHS -,-,- ii Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- ii
9、i Contents Page Foreword iv 1 Scope . 1 2 Normative references. 1 3 Terms and definitions. 1 4 Description of procedures. 3 4.1 Numerical recognition 3 4.2 Electromechanical recognition . 5 4.3 Self-regulation. 6 Annex A (normative) Structure of bar code. 7 Annex B (normative) Structure of 32-digit
10、bar code. 23 Annex C (normative) Magnetic cards. 36 Annex D (informative) Implanted-resistor connector . 52 Annex E (normative) Self-regulation 55 BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not fo
11、r Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- iv Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is no
12、rmally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in
13、 the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepa
14、re International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that so
15、me of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 13950 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 4, Plas
16、tics pipes and fittings for the supply of gaseous fuels. This first edition of ISO 13950 cancels and replaces ISO/TR 13950:1997, of which it constitutes a technical revision. BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee
17、=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- 1 Plastics pipes and fittings Automatic recognition systems for electrofusion joints 1 Scope This International Standard specifies the characteristics of automatic reco
18、gnition systems (numerical recognition by means of bar codes or magnetic cards, electromechanical recognition using implanted-resistor connectors and self-regulation systems) that enable the energy supply to be delivered automatically to the thermoplastic electrofusion fittings used in pipe jointing
19、. It is applicable to electrofusion fittings intended to be used for plastics piping systems for the conveyance of gaseous fuels, water for human consumption (including raw water prior to treatment) and for general purposes, or of other fluids. 2 Normative references The following referenced documen
20、ts are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO/IEC 7810:2003, Identification cards Physical characteristics ISO/IEC 7811-2:2
21、001, Identification cards Recording technique Part 2: Magnetic stripe Low coercivity ISO/IEC 7811-6:2001, Identification cards Recording technique Part 6: Magnetic stripe High coercivity 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 fitting
22、 accessory for the connection by fusion of thermoplastic pipes and/or other accessories 3.2 socket female part of a fitting in which the fusion is performed 3.3 coupler fitting constituted by two sockets 3.4 monofilar coupler fitting constituted of two sockets for which fusion is performed in a sing
23、le operation 3.5 bifilar coupler fitting constituted of two sockets for which fusion is performed separately BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo re
24、production or networking permitted without license from IHS -,-,- 2 3.6 saddle electrofusion fitting for by-passing, branching, ballooning or other operations 3.7 reduction electrofusion fitting for the assembly of two pipes and/or male terminating fittings of different dimensions 3.8 elbow electrof
25、usion fitting with two sockets with an angle 3.9 tee electrofusion fitting with three electrofusion sockets or two sockets and one male end 3.10 plug electrofusion fitting with one socket for plugging tubes and other accessories 3.11 connector end of the cable connecting the electrofusion accessory
26、to the fusion machine 3.12 terminal fixed part of the heating element located on the outside of the fitting to enable electrical connection to be made with the fitting 3.13 terminal shroud part of the fitting enabling the connector to be mounted externally 3.14 nominal fusion time fusion time, in se
27、conds, specified by the fitting manufacturer at the reference temperature and for the electrical parameters, such as nominal resistance, voltage and current, specified by the manufacturer 3.15 real fusion time fusion time, in seconds, used in reality, taking account, if necessary, of the ambient tem
28、perature and/or the real electrical parameters 3.16 fusion voltage voltage, in RMS AC volts, applied to the fitting during the fusion cycle 3.17 fusion current current, in amperes, flowing in the fitting and its supply circuit during the fusion cycle 3.18 nominal fusion energy energy, in kilojoules,
29、 specified by the fitting manufacturer at the reference temperature and for the electrical parameters whose values fall within the tolerance ranges specified by the manufacturer 3.19 real fusion energy energy, in kilojoules, consumed by the fitting at a given ambient temperature and for electrical p
30、arameters whose values fall within the tolerance ranges specified by the manufacturer BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction or networkin
31、g permitted without license from IHS -,-,- 3 3.20 Resistance of the heating element 3.20.1 nominal resistance ohmic resistance of the heating element at 23 C used in the basic design calculations for the electrofusion fitting, as specified by the manufacturer 3.20.2 identification resistance ohmic r
32、esistance of the heating element at 20 C measured on any electrofusion fitting 3.20.3 measured resistance ohmic resistance at the ambient temperature measured on any electrofusion fitting 3.21 resistivity reciprocal of the conductivity of the heating element, in ohm metres 3.22 temperature coefficie
33、nt of the heating element gradient of the change in resistance versus temperature, in reciprocal degrees kelvin 3.23 digit whole number from zero to nine 3.24 character whole number from zero to nine or a letter or a sign 4 Description of procedures 4.1 Numerical recognition 4.1.1 Principle Methods
34、for numerical recognition are based on systems such as bar codes and magnetic cards. Fusion parameters are recorded in code form on the data medium. At the manufacturers initiative or in response to user request, other information for fitting identification, identification of test data, fusion cycle
35、 optimization, additional safety measures, etc. can also be encoded For a heating cycle, the system reads, processes and memorizes the information recorded on the data medium. Successive messages are displayed, or signal tones emitted, to request the operator to follow a procedure, defined by the fi
36、tting manufacturer, specific to the fitting in question and including its recognition. 4.1.2 Field of application and limits Numerically controlled fusion machines capable of reading fusion parameters can be used for all electrofusion and electro-heating assembly techniques. The limits of this type
37、of fusion control unit shall be detailed by the manufacturer in terms of the maximum energy to be delivered, the fusion programmes incorporated, BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for
38、Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- 4 the fusion adaptations incorporated, and the limits of the programmable parameters. 4.1.3 Bar codes 4.1.3.1 General The system for entering data using bar codes offers a number of different user p
39、ossibilities, both for the fitting supplier and the manufacturer of the fusion machine: the fitting manufacturer records on the bar code the data he considers will be needed to ensure correct assembly, the amount of data depending on factors such as particular requirements or new technical developme
40、nts; the control unit manufacturer is free to develop his own software and the technical design of the unit, and can choose which data to display, which commands will be available, the criteria for fusion cycle emergency stop, and the display and recording of the various faults, the memorization met
41、hod for fusion data, etc. 4.1.3.2 Format of bar codes The format of bar codes shall one or the other of the following. a) The 24 digit “2-in-5” interleaved type. The ratio between the width of the thicker bar and the thinner bar shall be 2,5. The bar code content is summarized in Annex A. b) The 32
42、digit “2-in-5” interleaved type, including traceability coding as summarized in Annex B. The ratio between the width of the thicker bar and the thinner bar shall be 2,5. 4.1.3.3 Bar code structure The bar code structure shall have a predetermined overall length of either 24 digits or 32 digits. One
43、of these digits is composed by a control character (checksum). A complementary character set can be added if further data is required. The content of each digit shall be in accordance with Annex A or Annex B, as applicable. 4.1.4 Magnetic cards 4.1.4.1 General The system of data insertion by means o
44、f magnetic cards offers different possibilities for the fitting supplier, as well as for the user and control unit manufacturer. The fitting manufacturer records on the card the number of items of data necessary for the completion of an optimal fusion joint. In order to establish the fusion programm
45、e, he can choose between the functions described in Annex C, and adapt the data according to his wishes using nominal or real values. A fusion programme can contain up to 90 characters. The control unit manufacturer is completely free to develop his own software as well as the technological concept
46、of the unit. He can choose, among others, the data appearing on the display, the different commands, the emergency stop of the fusion cycle, as well as the display and recording of the different faults, the fusion data storage mode, etc., unless these are already prescribed in other standards. With
47、respect to the quality assurance of every fusion, a record containing all or part of the fusion process data can be stored either on the magnetic card or in the control box memory. When the fusion has been completed successfully and recorded on the magnetic card, the same magnetic card shall not be
48、used again to carry out another fusion. BS ISO 13950:2007 Copyright British Standards Institution Provided by IHS under license with BSI - Uncontrolled Copy Licensee=Boeing Co/5910770001 Not for Resale, 08/14/2008 22:16:42 MDTNo reproduction or networking permitted without license from IHS -,-,- 5 4.1.4.2 Description of techniq