《BS-EN-ISO-10350-1995.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-10350-1995.pdf（18页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS EN ISO 10350:1995 Incorporating Amendment No. 1 Plastics Acquisition and presentation of comparable single-point data The European Standard EN ISO 10350:1995 has the status of a British Standard Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncon
2、trolled Copy, (c) BSI BS EN ISO 10350:1995 This British Standard, having been prepared under the direction of the Plastics and Rubber Standards Policy Committee, was published under the authority of the Standards Board and comes into effect on 15 August 1994 BSI 03-2000 First published June 1988 Sec
3、ond edition August 1994 The following BSI references relate to the work on this standard: Committee reference PRM/21 Draft for comment 90/46956 DC ISBN 0 580 23411 8 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Plastics and Rubber Sta
4、ndards Policy Committee (PRM/-) to Technical Committee PRM/21, upon which the following bodies were represented: British Plastics Federation British Textile Confederation Department of the Environment (Building Research Establishment) Department of Trade and Industry (National Physical Laboratory) E
5、lectrical and Electronic Insulation Association (BEAMA Ltd.) GAMBICA (BEAMA Ltd.) Institute of Materials Ministry of Defence Packaging and Industrial Films Association Pira International RAPRA Technology Ltd. Amendments issued since publication Amd. No.DateComments 8821December 1995 Indicated by a s
6、ideline in the margin Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10350:1995 BSI 03-2000i Contents Page Committees responsibleInside front cover National forewordii Foreword2 Introduction3 1Scope3 2Normative references3 3Defini
7、tion4 4Specimen preparation and conditioning4 5Test requirements5 6Presentation of results5 Annex A (informative) Bibliography9 Table 1 Moulding parameters5 Table 2 Test conditions and format for the presentation of single-point data6 List of referencesInside back cover Licensed Copy: sheffieldun sh
8、effieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10350:1995 ii BSI 03-2000 National foreword This Part of BS 7008 has been prepared under the direction of the Plastics and Rubber Standards Policy Committee. It is identical with ISO 10350:1993 Plastics Acquisiti
9、on and presentation of comparable single-point data, published by the International Organization for Standardization (ISO). It supersedes BS 7008-1:1988, which is withdrawn. In 1995 the European Committee for Standardization (CEN) accepted ISO 10350:1993 as European Standard EN ISO 10350:1995. As a
10、consequence of implementing the European Standard this British Standard is renumbered as BS EN ISO 10350:1995 and any reference to BS 7008-1 should be read as a reference to BS EN ISO 10350. Cross-references International StandardCorresponding British Standard BS 2782 Methods of testing plastics ISO
11、 62:1980Methods 430A to 430D:1983 Determination of water absorption at 23 C. Determination of water absorption 23 C with allowance for water soluble matter. Determination of boiling water absorption Determination of boiling water absorption with allowance for water-soluble matter (Identical) ISO 75-
12、1:1993Method 121:1994 General test method for determination of temperature of deflection under load of plastics (Identical) ISO 75-2:1993Methods 121A to 121C:1994 Determination of temperature of deflection under load of plastics and ebonite (Identical) ISO 75-3:1993Method 121D:1994 Determination of
13、temperature of deflection under load of high-strength thermosetting laminates and long-fibre-reinforced plastics (Identical) ISO 178:1993Method 335A:1993 Determination of flexural properties (Identical) ISO 179:1993Method 359:1993 Determination of Charpy impact strength (Identical) ISO 291:1977Part
14、0:1992 Introduction (Annex A is identical) ISO 293:1986Method 901A:1988 Compression moulding test specimens of thermoplastic materials (Identical) ISO 294:1975Method 910A:1977 Injection moulding test specimens of thermoplastic materials (Identical) ISO 295:1991Method 902A:1992 Plastics. Compression
15、moulding of test specimens of thermosetting materials (Identical) Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 10350:1995 BSI 03-2000iii The Technical Committee has reviewed the provisions of ISO 899-1, ISO 1133, ISO 2577, ISO 2
16、818, IEC 243-1, IEC 250, IEC 296 and IEC 1006, to which normative reference is made in the text, and has decided that they are acceptable for use in conjunction with this standard. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards a
17、re responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. ISO 306:1987Methods 120A, 120B, 120D and 120E:1990 Determination of Vicat softening temperature of thermoplastics (Identical) ISO 527-1:1993Method 321:1994 Dete
18、rmination of tensile properties. General principles (Identical) ISO 527-2:1993Method 322:1994 Determination of tensile properties, test conditions for moulding and extrusion plastics (Identical) ISO 1183:1987Methods 620A to 620D:1991 Determination of density and relative density of non-cellular plas
19、tics (Identical) ISO 1210:1992Method 140A:1992 Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source (Identical) ISO 3146:1985Methods 125A to 125C2:1991 Determination of melting behaviour (melting temperature or melting range) of se
20、mi-crystalline polymers (Identical) ISO 4589:1984Method 141:1986 Determination of flammability by oxygen index (Identical) ISO 8256:1990Methods 354A and 354B:1991 Determination of tensile-impact strength (Identical) IEC 93:1980BS 6233:1982 Methods of test for volume resistivity and surface resistivi
21、ty of solid electrical insulating materials (Identical) IEC 112:1979BS 5901:1980 Method of test for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions (Identical) Summary of pages This document comprises a front cover, an inside front cove
22、r, pages i to iv, the EN ISO title page, pages 2 to 10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun
23、, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI iv blank Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10350 July 1995 ICS 83.080 Descriptors: Plastics, properti
24、es, tests, testing conditions, test results, data acquisition, data representation English version Plastics Acquisition and presentation of comparable single-point data (ISO 10350:1993) Plastiques Acquisitions et prsentation de caractristiques intrinsques comparables (ISO 10350:1993) Kunststoffe Erm
25、ittlung und Darstellung vergleichbarer Einpunktkennwerte (ISO 10350:1993) This European Standard was approved by CEN on 1995-01-12. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national stan
26、dard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other l
27、anguage made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Irel
28、and, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1995 All rights of reproduction and
29、communication in any form and by any means reserved in all countries to CEN and its members Ref. No. EN ISO 10350:1995 E Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10350:1995 BSI 03-2000 2 Foreword The text of the International S
30、tandard from ISO/TC 61, Plastics, of the International Organization for Standardization (ISO) has been taken over as a European Standard by the Technical Committee CEN/TC 249, Plastics. This European Standard shall be given the status of a national standard, either by publication of an identical tex
31、t or by endorsement, at the latest by January 1996, and conflicting national standards shall be withdrawn at the latest by January 1996. According to CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, G
32、ermany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10350:1995 BSI 03-20003 Introduction This Internati
33、onal Standard has been prepared because users of plastics find sometimes that available data cannot be used readily to compare the properties of similar materials, especially when the data have been supplied by different sources. Even when the same standard tests have been used, they often allow the
34、 adoption of a wide range of alternative test conditions, and the data obtained are not necessarily comparable. The purpose of this International Standard is to identify specific methods and conditions of test to be used for the acquisition and presentation of data in order that valid comparisons be
35、tween materials can be made. The present International Standard is concerned with tests employed to present “single-point” data on the limited range of properties commonly included in data sheets and used for the preliminary selection of materials. Such data represent the most basic approach to the
36、specification of properties of materials and this International Standard thus facilitates the first steps towards more efficient selection and use of plastics in the many applications to which they are suited. A complementary International Standard (to be published as ISO 11403, in several parts) wi
37、ll be concerned with the standardized acquisition and presentation of “multi-point” data, to demonstrate how properties vary with important factors such as time, temperature and the presence of particular natural and chemical environments. In that standard, some additional properties will be include
38、d. Its use will provide a more substantial database than one containing only single-point data, and so will enable improved assessment of the fitness of a material for any particular application. In addition, ISO 11403-1, which deals with mechanical properties, assists predictions of the performance
39、 of components and ISO 11403-2, covering thermal and processing properties, aids predictions of melt-flow behaviour during manufacturing. ISO 11403-3 will be concerned with environmental influences on properties, and other parts may be prepared to cover additional properties. 1 Scope This Internatio
40、nal Standard identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value although in certain cases properties are represented by two values obtained under d
41、ifferent test conditions. The properties included are those presented conventionally in manufacturers data sheets. The test methods and test conditions apply predominantly to those plastics that may be injection-or compression-moulded or prepared as sheets of specified thickness. 2 Normative referen
42、ces The following standards contain provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agreements based on this International Stan
43、dard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of currently valid International Standards. ISO 62:1980, Plastics Determination of water absorption. ISO 75-1:1993, Plastics Determinati
44、on of temperature of deflection under load Part 1: General test method. ISO 75-2:1993, Plastics Determination of temperature of deflection under load Part 2: Plastics and ebonite. ISO 75-3:1993, Plastics Determination of temperature of deflection under load Part 3: High-strength thermosetting lamina
45、tes and long-fibre-reinforced plastics. ISO 178:1993, Plastics Determination of flexural properties. ISO 179:1993, Plastics Determination of Charpy impact strength. ISO 291:1977, Plastics Standard atmospheres for conditioning and testing. ISO 293:1986, Plastics Compression moulding test specimens of
46、 thermoplastic materials. ISO 294:, Plastics Injection moulding of test specimens of thermoplastic materials1). ISO 295:1991, Plastics Compression moulding of test specimens of thermosetting materials. 1) To be published. (Revision of ISO 294:1975) Licensed Copy: sheffieldun sheffieldun, na, Mon Nov
47、 20 02:13:51 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 10350:1995 4 BSI 03-2000 ISO 306:1987, Plastics Thermoplastic materials Determination of Vicat softening temperature. ISO 527-1:1993, Plastics Determination of tensile properties Part 1: General principles. ISO 527-2:1993, Plastics Deter
48、mination of tensile properties Part 2: Test conditions for moulding and extrusion plastics. ISO 899-1:1993, Plastics Determination of creep behaviour Part 1: Tensile creep. ISO 1133:1991, Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics. I
49、SO 1183:1987, Plastics Methods for determining the density and relative density of non-cellular plastics. ISO 1210:1992, Plastics Determination of the burning behaviour of horizontal and vertical specimens in contact with a small-flame ignition source. ISO 2577:1984, Plastics Thermosetting moulding materials Determination of shrinkage. ISO 2818:1980, Plastics Preparation of test specimens by machining. ISO 3146:1985, Plastics Determination of melting behaviour (melting temperature or melting rang