《BS-ISO-7919-5-2005.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-7919-5-2005.pdf（24页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS ISO 7919-5:2005 Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 5: Machine sets in hydraulic power generating and pumping plants ICS 17.160; 29.160.40 ? Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Un
2、controlled Copy, (c) BSI BS ISO 7919-5:2005 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 16 May 2005 BSI 16 May 2005 ISBN 0 580 45969 1 National foreword This British Standard reproduces verbatim ISO 7919-5:2005 and implements it as the UK
3、 national standard. It supersedes BS ISO 7919-5:1997 which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee GME/21, Mechanical vibration and shock, to Subcommittee GME/21/5, Vibration of machines, which has the responsibility to: A list of organizations repr
4、esented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by
5、using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunit
6、y from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in
7、 the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii to iv, pages 1 to 16, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since p
8、ublication Amd. No. DateComments Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Reference number ISO 7919-5:2005(E) OSI 5002 INTERNATIONAL STANDARD ISO 7919-5 Second edition 2005-04-15 Mechanical vibration Evaluation of machine vibration by
9、 measurements on rotating shafts Part 5: Machine sets in hydraulic power generating and pumping plants Vibrations mcaniques valuation des vibrations des machines par mesurages sur les arbres tournants Partie 5: Machines quipant les centrales hydrolectriques et les stations de pompage BS ISO 79195:20
10、05 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI IS-9197 O5:(5002E) DPlcsid Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebtlnu deess
11、the typefaces whice era hml era deddebicsnede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tredamafo kr
12、 Aebod SystemI sncotaropr.de teDails fo teh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo the file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In tl
13、nu ehikletneve y ttah lborp aem leratit gno it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ISO 5002 All irthgs erse.devr lnUeto sswrehise specified, on trap fo this lbupictaion maeb y cudorperro de tuilizi den yna form ro na ybm ynae,s lecetrinoc ro mecinahcal, inclid
14、ung tohpcoiypodna gn micrfoilm, wittuoh repmissii non writign from ietI rehSa Ot tsserdda eh ebolw or ISOs memreb i ydobn the cnuotrfo y ttseuqer ehe.r ISO cirypothg fofice saCe tsopale 65 eneG 1121-HC 02 av leT. 4 + 10 947 22 1 11 xaF0 947 22 14 + 9 74 E-mail coirypthgiso.o gr We bwww.is.o gro Pulb
15、isdehi n Switlrez dna ii ISO 5002 Allr ithgsr esedevr BS ISO 79195:2005 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI IS-9197 O5:(5002E) IS4002 O Allr ihgtsser edevr iii Contents Page Forewordiv 1 Scope1 2 Normative references .2 3 Measure
16、ment procedures 2 3.1 General.2 3.2 Measurement type.2 3.3 Measurement planes.3 3.4 Measuring equipment.3 4 Evaluation criteria.3 4.1 Turbine operating conditions 3 4.2 Pump operating conditions4 4.3 Special operating conditions.4 Annex A (normative) Evaluation criteria for relative shaft vibration
17、of hydraulic turbine sets under specified operating conditions5 Annex B (informative) Special features of shaft vibration of hydraulic machine sets10 Annex C (informative) Analysis procedure and applied regression technique.12 Annex D (informative) Objectives of this edition of ISO 7919-5.14 Bibliog
18、raphy .16 BS ISO 79195:2005 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI IS-9197 O5:(5002E) iv IS4002 O Allr ihgtsser edevr Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards
19、bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizat
20、ions, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in th
21、e ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of
22、the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7919-5 was prepared jointly by Technical Committee ISO/TC 108,
23、Mechanical vibration and shock, Subcommittee SC 2, Measurement and evaluation of mechanical vibration and shock as applied to machines, vehicles and structures, and Technical Committee IEC/TC 4, Hydraulic turbines. The draft was circulated for voting to the national bodies of ISO and IEC separately.
24、 This second edition cancels and replaces the first edition (ISO 7919-5:1997), of which it constitutes a technical revision. Evaluation criteria have been modified, substituting the former four evaluation zones by a more global division of the whole evaluation area into two major ranges, with change
25、d definitions and divided by the former B/C borderline. Inside the two major ranges A-B and C-D, the old borderlines A/B and C/D are kept to indicate different statistically based severity grades. More information on the objectives of this revision is given in Annex D. ISO 7919 consists of the follo
26、wing parts, under the general title Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts: Part 1: General guidelines Part 2: Land-based steam turbines and generators in excess of 50 MW with normal operating speeds of 1 500 r/min, 1 800 r/min, 3 000 r/min and 3 600
27、r/min Part 3: Coupled industrial machines Part 4: Gas turbine sets Part 5: Machine sets in hydraulic power generating and pumping plants BS ISO 79195:2005 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTENRATIONAL TSANDADR IS-9197 O5:(500
28、2E) I SO 5002 All irthgs ersedevr 1 Mechanical vibration Evaluation of machine vibration by measurements on rotating shafts Part 5: Machine sets in hydraulic power generating and pumping plants 1 Scope This part of ISO 7919 gives guidelines for applying evaluation criteria for shaft vibration measur
29、ed at, or close to, the bearings of machines or machine sets in hydraulic power generating and pumping plants under normal operating conditions. These guidelines are presented in terms of both steady-state running vibration and any amplitude changes that can occur in these steady vibration values. N
30、OTE 1 The numerical values specified are not intended to serve as the only basis for vibration evaluation since, in general, the vibratory condition of a machine is assessed by consideration of both the shaft vibration and the associated structural vibration (see ISO 7919-1 and ISO 10816-1). This pa
31、rt of ISO 7919 is applicable to machines or machine sets in hydraulic power generating and pumping plants where the hydraulic machines have speeds from 60 r/min to 1 800 r/min, shell- or shoe-type sleeve bearings, and main engine power of at least 1 MW. The position of the shaft line can be vertical
32、, horizontal or at an arbitrary angle between these two directions. Machine sets covered by this part of ISO 7919 include a combination of hydraulic turbines and generators, pumps and electrical machines operating as motors, pump-turbines and motor-generators, and hydraulic turbines, pumps and motor
33、-generators (classic pump-storage machine sets), including auxiliary equipment (e.g. starting turbines or exciters lying in the shaft line). This part of ISO 7919 is also applicable to turbines or pumps connected to generators or electrical motors via gears and/or radially flexible couplings. NOTE 2
34、 Electrical machines with speeds between 1 000 r/min and 1 800 r/min are evaluated according to the criteria specified in ISO 7919-3. This part of ISO 7919 is not applicable to pumps in thermal power plants or industrial installations (for these machines, see ISO 7919-3), hydraulic machines or machi
35、ne sets having rolling element bearings, or hydraulic machines with water-lubricated bearings. BS ISO 79195:2005 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI IS-9197 O5:(5002E) 2 I SO 5002 All irthgs ersedevr As specified in ISO 7919-1, s
36、haft vibration of machines or machine sets in hydraulic power generating and pumping plants can be determined with regard to the following tasks: task A: changes in vibrational behaviour; task B: excessive kinetic load; task C: the monitoring of radial clearance. 2 Normative references The following
37、 referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7919-1, Mechanical vibration of non-reciprocating machines
38、 Measurements on rotating shafts and evaluation criteria Part 1: General guidelines ISO 10817-1, Rotating shaft vibration measuring systems Part 1: Relative and absolute sensing of radial vibration IEC 60994, Guide for field measurement of vibrations and pulsations in hydraulic machines (turbines, s
39、torage pumps and pump-turbines) 3 Measurement procedures 3.1 General The measurement procedures to be followed and the instrumentation to be used shall be as described in ISO 7919-1 and IEC 60994. 3.2 Measurement type Relative and absolute shaft vibration measurements are carried out on hydraulic ma
40、chine sets using non- contacting transducers. Shaft-riding probes with seismic transducers cannot generally be used due to the very low frequency range of the measuring equipment required for low-speed hydraulic machinery. For relative measurements, transducers should be mounted directly on the bear
41、ing shell or the bearing pad. If the transducers are installed on the bearing support structure or bearing housing, as it is common for vertical machines, care shall be taken that the relative motion between the bearing shell or pad and the transducer itself is small compared with the shaft motion.
42、If this is not so, the measured signal cannot be said to be representative of the relative movement between the shaft and bearing shell or bearing pad, respectively. This requirement can be assessed by static analysis of the structure or additional measurements; the latter is usually difficult and e
43、xpensive. With regard to the transducer support structures, it is advisable that the lowest natural frequency of those vibration modes that create significant movements in the working direction of shaft displacement transducers be greater than seven times the synchronous rotational frequency, and sh
44、ould not be a direct multiple of the synchronous rotational frequency. The absolute vibration of the support frame should always be measured using seismic transducers installed on the support frame as close as possible to the shaft movement transducer and in the same direction of action. The reading
45、s from the seismic transducers may be used after conversion into displacements to evaluate the absolute shaft displacement. NOTE Apart from the shaft vibration, the vibration of the bearing support is frequently monitored as well. The vibration measurement at the lower guide bearings of vertical mac
46、hines can, however, be misinterpreted. The vibration value measured at the bearings and their supports, which are rigidly embedded in the building, is sometimes produced by hydraulic forces, directly transmitted from the hydraulic machine via the foundation, and is not produced by radial shaft vibra
47、tion. BS ISO 79195:2005 Licensed Copy: sheffieldun sheffieldun, na, Sun Nov 26 04:34:28 GMT+00:00 2006, Uncontrolled Copy, (c) BSI IS-9197 O5:(5002E) I SO 5002 All irthgs ersedevr 3 3.3 Measurement planes Measurement tasks A and B (see Clause 1) require measurements to be taken at all main bearings
48、of the machine set. If possible, the setting of the transducers at the different bearings should be in line. For vertical machines, in most cases the preferred measurement directions are upstream and 90 apart in the direction of rotation. For horizontal machines, the measurement directions are often
49、 chosen to be 45 from the vertical for practical reasons. For monitoring purposes (task A) only, in some cases the measurement planes may be reduced to the most important ones, mainly at machine sets with four or more bearings. The selection should be based on vibration performance analyses, simulating all types of faults or disturbing events. The preferred measurement planes should be those where possible disturbing events