《BS-ISO-98-2001.pdf》由会员分享，可在线阅读，更多相关《BS-ISO-98-2001.pdf（12页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS ISO 98:2001 ICS 59.120
2、.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Textile machinery and accessories Spinning preparatory and spinning machinery Main dimensions of coverings for top rollers Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c)
3、 BSI This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 April 2001 BSI 04-2001 ISBN 0 580 36986 2 BS ISO 98:2001 Amendments issued since publicat
4、ion Amd. No.DateComments National foreword This British Standard reproduces verbatim ISO 98:2001 and implements it as the UK national standard. The UK participation in its preparation was entrusted to Technical Committee TCI/33, Textile machinery, which has the responsibility to: aid enquirers to un
5、derstand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented
6、on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by usi
7、ng the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity f
8、rom legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issu
9、ed. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARD ISO 98 Third edition 2001-03-01 Reference number ISO 98:2001(E) Textile machinery and accessories Spinning preparatory and spinning machinery Main dimensions of cover
10、ings for top rollers Matriel pour lindustrie textile Matriel de prparation de filature et de filature Dimensions principales des garnitures pour cylindres suprieurs Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 98:2001(E) ii Licensed C
11、opy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 98:2001(E) iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standa
12、rds is normally carried out through ISO technical com- mittees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liai- son with ISO, also
13、 take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopte
14、d by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the sub
15、ject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 98 was prepared by Technical Committee ISO/TC 72,Textile machinery and machinery for dry-cleaning and industrial laundering, Subcommittee SC 1,Spinning preparatory, spin
16、ning, twisting and winding machinery and accessories. This third edition cancels and replaces the second edition (ISO 98:1977), which has been technically revised. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sh
17、effieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARDISO 98:2001(E) 1 Textile machinery and accessories Spinning preparatory and spinning machinery Main dimensions of coverings for top rollers 1Scope This International Standard specifies the main dimens
18、ions of coverings for ready-for-use top rollers (synthetic cover- ings). It is applicable to spinning preparatory and spinning machinery. 2Symbols bare roller diameter diameter with covering (finished ground) width of covering saddle force Btype of execution of covering with rectangular sides (see F
19、igure 1 and Figure 2) Ctype of execution of covering with beveled sides (see Figure 1 and Figure 2) Dtype of execution of covering with rounded sides (see Figure 1 and Figure 2) d1 d2 b F Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO 9
20、8:2001(E) 2 3Dimensions 3.1Single-boss top rollers The main dimensions of coverings for single-boss top rollers used for spinning preparatory machinery (e.g. draw- frames and comber), are given in Figure 1 and Tables 1, 2 and 3 (see Figure 2 for twin-boss top rollers). In the case of single-boss top
21、 rollers with removable bushings execution is similar to that shown in Figure 3. Figure 1 Diameters and covering widths for single-boss top rollers Table 1 Bare roller diameter Dimensions in millimetres 1618192326283035404550556065707580 NOTEFor, in increments of 10. Table 2 Roller diameter with cov
22、ering (finished ground) Dimensions in millimetres 25283234364045505560657075808590 NOTEFor, in increments of 10. Table 3 Width of covering Dimensions in millimetres 8090100110125140160180200220250280315355400450 d1 d180 d2 d290 b Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00
23、:00 2006, Uncontrolled Copy, (c) BSI ISO 98:2001(E) 3 3.2Twin-boss top rollers The main dimensions of coverings for twin-boss top rollers used for spinning and roving frames are given in Figure 2 and Tables 4, 5 and 6. In the case of twin-boss top rollers with removable bushings, execution is simila
24、r to that shown in Figure 3. Figure 2 Diameters and covering widths for twin-boss top rollers Table 4 Bare roller diameter Dimensions in millimetres 1923252830354045505560 NOTEFor, in increments of 10. Table 5 Roller diameter with covering (finished ground) Dimensions in millimetres 2528303235404550
25、556065707580 NOTEFor, in increments of 5. Table 6 Width of covering Dimensions in millimetres 2528303234354045505560 NOTEFor, in increments of 10. Figure 3 Covering fixed to a removable bushing d1 d160 d2 d280 b b 60 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Unc
26、ontrolled Copy, (c) BSI ISO 98:2001(E) 4 4Designation of coverings The designation shall include a reference to this International Standard, followed by the dimensions,andex- pressed in millimetres, the Shore A hardness, the type of execution and the saddle forceexpressed in decanew- tons. If no spe
27、cification is given by the buyer, the manufacturer may supply any of the three executions, B, C or D. EXAMPLEA covering in accordance with ISO 98 of dimensions,and, a Shore A hard- ness of 80, of execution type B and a forcedecanewtons is designated as follows: ISO 98-28 ? ? ? ? 40 ? ? ? ? 160-80-B-
28、40 d1d2b F d1=28 mmd2=40 mmb =160 mm F =40 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS ISO 98:2001 BSI 389 Chiswick High Road L
29、ondon W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution
30、 BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should m
31、ake sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee r
32、esponsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI,
33、international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation
34、 of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information
35、 services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. F
36、or details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Further information about BSI is available on the BSI website at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the pub
37、lications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written pe
38、rmission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 27 02:13:08 GMT+00:00 2006, Uncontrolled Copy, (c) BSI