《BS-EN-ISO-14530-3-2000.pdf》由会员分享，可在线阅读，更多相关《BS-EN-ISO-14530-3-2000.pdf（14页珍藏版）》请在三一文库上搜索。
1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN ISO 14530-3:2000 Th
2、e European Standard EN ISO 14530-3:1999 has the status of a British Standard ICS 83.080.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3: Requirements for selected moulding compounds Licensed Copy: she
3、ffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI This British Standard, having been prepared under the direction of the Sector Committee for Materials and Chemicals, was published under the authority of the Standards Committee and comes into effect on 15 Janua
4、ry 2000 BSI 01-2000 ISBN 0 580 35887 9 BS EN ISO 14530-3:2000 Amendments issued since publication Amd. No.DateComments National foreword This British Standard is the English language version of EN ISO 14530-3:1999. It is identical with ISO 14530-3:1999. The UK participation in its preparation was en
5、trusted to Technical Committee PRI/42, Fibre reinforced thermosetting plastics and prepregs, which has the responsibility to: aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep the U
6、K interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references Attention is drawn to the fact that CEN and CENELEC Standards normally incl
7、ude an annex which lists normative references to international publications with their corresponding European publications. The British Standards which implement these international or European publications may be found in the BSI Standards Catalogue under the section entitled International Standard
8、s Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard doe
9、s not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 4, an inside back cover and a back cover. The BSI cop
10、yright notice displayed in this document indicates when the document was last issued. Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI
11、EN ISO 14530-3:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ? Reference number ISO 14530-3:1999(E) INTERNATIONAL STANDARD ISO 14530-3 First edition 1999-11-15 Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 3:
12、 Requirements for selected moulding compounds Plastiques Poudres mouler base de polyester non satur (UP-PMC) Partie 3: Exigences relatives certaines poudres mouler EN ISO 14530-3:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -0354
13、13:(9991E) ISO 9991 All rgihts resvrede. lnUess torehwise scepfieid, no rapt of this ilbupctaoin may be udorperced or utzilied in nay form or by nay snaem, electnoric or mecinahcal, inclidung tohpociypong nad micrfoilm, wituoht eprmission in writing from eitehr ISO at the rddaess lebow or ISOs memeb
14、r ydob in the ctnuory of the rtseuqee.r ISO cirypohgt fofice aCse soptale 56 ? 121-HC1 veneGa 20 leT. + 41 22 479 01 11 aFx + 41 22 374 10 97 E-mail cirypothgiso.ch Web www.iso.ch ii? DPF dcsilremia ihTs PDF file may ctnoain emeddebd tyfepaces. In accnadroce with Aebods licensing lopicy, this file m
15、ay be pirnted or ivewed ubt slahl ton be ideted lnuess the tyfepaces which are emeddebd rae licensed to nad intslaled on the computer freporming the ideting. In odwlnidaong this feli, trapies accept tierehn the sersnoptilibiy of ont infrnignig Aebods licsnenig lopicy. hTe ISO tneCarl Secterairat acc
16、epts no llibaiity in this .aera Abode is a tdaremark of Abode Stsyems Inctaropro.de teDails of the sfotwrae pudorcts used to crtaee tihs PDF file can be fnuod in the Garenel Info lerative to the file; the P-FDceration rapamteers were tpoimized for pirtning. Evrey crae ahs eebn taken to ensrue that t
17、he file is suitlbae for use by ISO memebr idobse. In the lnuikley etnev taht a plborem lerating to it is fdnuo, lpaese ifnorm the tneCarl Secterairat at the serddas given lebow. EN ISO 14530-3:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c)
18、 BSI ISO -035413:(9991E) ?iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interes
19、ted in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical C
20、ommission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication
21、as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this part of ISO 14530 may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent
22、 rights. International Standard ISO 14530-3 was prepared by Technical Committee ISO/TC 61,Plastics, Subcommittee SC 12,Thermosetting materials. ISO 14530 consists of the following parts, under the general titlePlastics Unsaturated-polyester powder moulding compounds (UP-PMCs): ?Part 1: Designation s
23、ystem and basis for specifications ?Part 2: Preparation of test specimens and determination of properties ?Part 3: Requirements for selected moulding compounds Annex A of this part of ISO 14530 is for information only. EN ISO 14530-3:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:
24、33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN ISO 14530-3:1999 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI INTERNATIONAL STANDARDISO 14530-3:1999(E) ISO 9991 All irhgts seredevr1 Plastics Unsaturated-polyester powder moulding compound
25、s (UP-PMCs) Part 3: Requirements for selected moulding compounds 1Scope This part of ISO 14530 specifies the requirements for the physical and chemical properties of unsaturated-polyester powder moulding compounds (UP-PMCs) and compression- or injection-moulded test specimens produced from them. It
26、is limited to those powder moulding compounds whose composition and properties are significantly different. It is further limited to those moulding compounds which are of general technical and/or economic importance. The properties which are used to characterize the moulding compounds, the test meth
27、ods and the test conditions are selected from those given in ISO 14530-2. The moulding compounds are divided into types according to their composition and properties. The various types are designated using the designation system defined in ISO 14530-1. 2Normative references The following normative d
28、ocuments contain provisions which, through reference in this text, constitute provisions of this part of ISO 14530. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this part of ISO 14530 are encouraged t
29、o investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 472:1999,
30、Plastics Vocabulary. ISO 14530-1:1999,Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 1: Designation system and basis for specifications. ISO 14530-2:1999,Plastics Unsaturated-polyester powder moulding compounds (UP-PMCs) Part 2: Preparation of test specimens and determinatio
31、n of properties. 3Terms and definitions For the purposes of this part of ISO 14530, the terms and definitions given in ISO 472, ISO 14530-1 and ISO 14530-2 apply. EN ISO 14530-3:1999 1 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035
32、413:(9991E) 2 ISO 9991 All irhgts seredevr 4Requirements 4.1Property values In order for an unsaturated-polyester powder moulding compound to be considered as complying with this part of ISO 14530, it shall meet the requirements given in Table 1. Table 1 gives the mean value obtained for the set of
33、test specimens used to determine a particular property. Individual values of properties 2.1, 2.2, 2.3 and 2.4 shall be within 10 % of the mean value, and individual values of properties 3.1 and 3.2 shall be within 5 C of the mean value. No specific limits are placed on rheological and processing pro
34、perties. However, suitable rheological and processing properties are essential for the satisfactory use of a moulding compound. The test methods and test conditions used shall be as agreed between the interested parties. In addition, for some applications, it may be useful for information to be made
35、 available on other properties, for example: ?cure time; ?particle size; ?moisture content. If this is so, these properties and test methods, as well as the test conditions to be used, shall be as agreed between the interested parties. 4.2Filler/reinforcement type and content In order for a phenolic
36、 powder moulding compound to be considered as complying with this part of ISO 14530, the nature, form and content by mass of its filler/reinforcement shall be as given in the designation of the moulding compound (see ISO 14530-1:1999, subclause 4.2). EN ISO 14530-3:1999 2 Licensed Copy: sheffieldun
37、sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035413:(9991E) ISO 9991 All irhgts seredevr3 Table 1 Property requirements for UP-PMCs containing (GF+MD) or (LD+MD) as filler 1234 Type: PMC ISO 14530-UP. . . PropertyUnit Pro- cess- inga Max. or min. (GF10+MD60) t
38、o (GF20+MD50) (GF10+MD65),X,F to (GF20+MD55),X,F (LD20+MD50) to (LD30+MD40) 1Rheological and processing properties 1.1To be agreed between the interested parties 2Mechanical properties 2.1Stress at break, ?BMPa Q M W W 35 45 35 45 25 35 2.2Flexural strength, ?fMMPa Q M W W 80 100 80 1000 70 80 2.3Ch
39、arpy impact strength, acU kJ/m2 Q M W W 5,0 7,5 5,0 7,5 4,5 5,0 2.4Charpy notched impact strength, acA kJ/m2 Q M W W 1,1 1,3 1,1 1,3 1,0 1,0 3Thermal properties 3.1Temperature of deflection under load, Tf1,8 CQ/MW250250110 3.2Temperature of deflection under load, Tf8,0 CQ/MW18018070 3.3Flammability
40、(glow bar), BH Q/MuBH 2-95BH 2-10BH 2-30 4Electrical properties 4.1Dissipation factor, tan? 100 Q/Mu0,030.03 4.2Volume resistivity, ?e?cmQ/MW101310131011 4.3Surface resistivity, ?e?Q/MW101210121010 4.4Proof tracking index, PTIQ/MW600600600 5Other properties 5.1mgu5050200 5.2 Water absorption, Ww24 %
41、 by mass Q/M u a Q = Compression moulding M = Injection moulding NOTE 1See ISO 14530-2:1999, Tables 3 and 4, columns 3, 4, and 7, for the methods to be used for the preparation of test specimens and the determination of properties. NOTE 2In view of the differences between the property-value limits f
42、or compression-moulding and injection-moulding materials, the likely variations in test results and the wide range of properties covered, it should not be assumed that materials having the same designation are exactly equivalent. EN ISO 14530-3:1999 3 Licensed Copy: sheffieldun sheffieldun, na, Mon
43、Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI ISO -035413:(9991E) 4 ISO 9991 All irhgts seredevr Annex A (informative) Comparison of designations Table A.1 Comparison of designations used for UP-PMCs in national and international standards 1234 National or international standard Type: P
44、MC ISO 14530-UP. . . ISO 14530-3:1999 (GF10+MD60) to (GF20+MD50) (GF10+MD65),X,F to (GF20+MD55),X,F (LD20+MD50) to (LD30+MD40) ISO ASTM BS DIN 16911:1978802804 JIS NF EN ISO 14530-3:1999 4 Licensed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI Lice
45、nsed Copy: sheffieldun sheffieldun, na, Mon Nov 20 02:24:33 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS EN ISO 14530-3:2000 BSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
46、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the inter
47、national level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. W
48、e would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual
49、 updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless oth