《DD-CEN-TS-15810-2008.pdf》由会员分享，可在线阅读，更多相关《DD-CEN-TS-15810-2008.pdf（28页珍藏版）》请在三一文库上搜索。
1、DD CEN/TS 15810:2008 ICS 01.080.20; 91.140.01 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW DRAFT FOR DEVELOPMENT Graphical symbols for use on integrated building automation equipment Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncon
2、trolled Copy, (c) BSI This Draft for Development was published under the authority of the Standards Policy and Strategy Committee on 31 December 2008 BSI 2008 ISBN 978 0 580 62159 8 Amendments/corrigenda issued since publication DateComments DD CEN/TS 15810:2008 National foreword This Draft for Deve
3、lopment is the UK implementation of CEN/TS 15810:2008. This publication is not to be regarded as a British Standard. It is being issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and experien
4、ce of its practical application can be obtained. Comments arising from the use of this Draft for Development are requested so that UK experience can be reported to the international organization responsible for its conversion to an international standard. A review of this publication will be initiat
5、ed not later than 3 years after its publication by the international organization so that a decision can be taken on its status. Notification of the start of the review period will be made in an announcement in the appropriate issue of Update Standards. According to the replies received by the end o
6、f the review period, the responsible BSI Committee will decide whether to support the conversion into an international Standard, to extend the life of the Technical Specification or to withdraw it. Comments should be sent to the Secretary of the responsible BSI Technical Committee at British Standar
7、ds House, 389 Chiswick High Road, London W4 4AL. The UK participation in its preparation was entrusted to Technical Committee RHE/16, Performance requirements for control systems. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does
8、 not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled
9、Copy, (c) BSI DD CEN/TS 15810:2008 TECHNICAL SPECIFICATION SPCIFICATION TECHNIQUE TECHNISCHE SPEZIFIKATION CEN/TS 15810 November 2008 ICS 01.080.20; 91.140.01 English Version Graphical symbols for use on integrated building automation equipment Symboles graphiques utiliser sur les quipements dautoma
10、tisation intgre de btiment Graphische Symbole auf Einrichtungen der integrierten Gebudeautomation This Technical Specification (CEN/TS) was approved by CEN on 9 June 2008 for provisional application. The period of validity of this CEN/TS is limited initially to three years. After two years the membe
11、rs of CEN will be requested to submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard. CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available promptly at national level
12、in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech
13、 Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROP
14、EN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: rue de Stassart, 36 B-1050 Brussels 2008 CENAll rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. CEN/TS 15810:2008: E Licensed Copy: London South Bank University, South Bank
15、 University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms and definitions .5 4 Symbols overview6 5 Symbols tables .6 5.1 General 6 5.2 Elementary symbols 7 5.3 Symbols 9 Bibliography . 24
16、 Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 3 Foreword This document (CEN/TS 15810:2008) has been prepared by Technical Committee CEN/TC 247 “Building Automation, Controls and Building Ma
17、nagement”, the secretariat of which is held by SNV. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. For application to building automa
18、tion equipments, this European Document takes up some symbols and their titles without modification from international documents ISO 7000 or IEC 60417-1. Some other existing symbols actually present on devices of the market complete these symbols. According to the CEN/CENELEC Internal Regulations, t
19、he national standards organizations of the following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlan
20、ds, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 4 Introduction This international
21、document presents graphical symbols for use on control, integrated automation equipment or technical building management equipments and systems. Ease of use automation functionalities requires clear graphical symbols, readable independently of language, i.e. internationally recognising. For building
22、 energy performance, it is important to take account expected behaviour of people encouraged to save energy through building automation equipment. Ease of use is a prime means to get realistic performance during exploitation. Professionals or end users are able to reduce largely energy consumptions
23、by setting easily operating modes and functions parameters for best adaptation of mechanical services functionalities to needs. For this purpose, graphical symbols constitute the best readable mean, mainly if these graphical elements are largely, internationally used by manufacturers of control, int
24、egrated automation equipment or technical building management equipments and systems. NOTE This document, therefore, is contributing to the general European policy for energy saving, particularly in the fields of the Construction Products Directive (89/106/EEC) Essential Requirements n 6 Energy econ
25、omy and heat retention (and its interpretative document) and of the Energy Performance of Building Directive (2002/91/CE). Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 5 1 Scope This docume
26、nt provides a synopsis of graphical symbols which are intended to be placed on building equipments and/or technical documentation of products in order to instruct the person(s) using the equipments. These graphical symbols are primary intended: to identify control or automation or technical manageme
27、nt equipments or part of these equipments: electronic devices (e.g. controller, scheduler, optimiser, etc.), sensors, actuators, to indicate functions and their operating modes, to indicate settings for modes and functions parameters introduction, to designate connexions, to provide instruction to u
28、sers (professional and/or end user) for the operation of the equipment. The graphical symbols in this document are not primarily intended for: safety signs, public information, schematics for systems principles. 2 Normative references The following referenced documents are indispensable for the appl
29、ication of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. N/A 3 Terms and definitions 3.1 graphical symbol visually perceptible figure with a particular meaning used to tra
30、nsmit information independently of language (see ISO 17724:2003) 3.2 elementary symbol graphical elements able to be combined with other(s) element(s) to create a new symbol associating their meanings 3.3 function autonomous operation providing output(s) in relation with data input(s) and parameters
31、 NOTE Functions within a BACS are referred to as control functions, I/O, processing, optimization, management and operator functions (see EN ISO 16484-2). Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 1581
32、0:2008 (E) 6 3.4 mode state of a function, device, equipment or a system defining the manner by which it performs its operation (EN 12098-5) NOTE Synonymous: “functional modes”, “operation modes”, “operational modes”. 4 Symbols overview These symbols are normally printed or screened on black and whi
33、te or two colours, e.g. a dark colour and white. Colour is not an element for the meaning. These symbols are readable static pictures, animation on a screen is not an element for the meaning. The meaning of each graphical symbol may depend upon its orientation in a given reference system and care sh
34、ould be taken to avoid ambiguity (e.g. by rotating or mirroring). Technology for display, print, paint or show on screen, project onto sufficient resolution for keep readability. Each graphical symbol may be used in any field of building equipment, provided its meaning is clearly understood. 5 Symbo
35、ls tables 5.1 General Symbols in Tables 1 and 2 are selected in accordance with these rules: priority for graphical symbols from standards ISO 7000 and IEC 60417. Drawing, title and eventual comments (IEC 60147-1) are copied without modification; completed by symbols based on manufacturers recognize
36、d practices; no new symbols if they can not be found on devices on the market. In these tables: Column 1 - N: allocated number, without ordering signification. Column 2 - Symbol: drawing. Column 3 - Source: indicates origin of the symbol and allocated number in ISO 7000 or IEC 60147-1 standards. If
37、the symbol came from another origin (e.g. national standards or manufacturers), the source is not labelled. Column 4 - TITLE: signification of symbol from ISO 7000 or IEC 60147-1 standard or another origin. On IEC 60417-1 the title of symbols is completed by a description. An extract from this descr
38、iption is copied from IEC 60417-1 in this column. Column 5 - Application AIR CONDITIONING Title: COOLING; AIR CONDITIONING unchanged This snow flake differs from snow flake n 10, intended to avoid ambiguity/mix-up with frost. 10 Part of ISO 7000 n 2614 ICY ROAD CONDITION Title: FROST, ICY This snow
39、flake differs from snow flake n 8, intended to avoid ambiguity/mix-up with cooling. 12 ISO 7000 n 034 TEMPERATURE Title: TEMPERATURE unchanged 14 ISO 7000 n 0505 RELATIVE HUMIDITY, MOISTURE CONTENT Title: RELATIVE HUMIDITY, MOISTURE CONTENT unchanged 16 ISO 7000 n 0159 LEVEL Title: LEVEL unchanged 1
40、8 Part of ISO 7000 Part of n0224 and many other MEASURE . or MEASUREMENT Title: MEASURE unchanged Include measured physical symbol on the circle. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E
41、) 8 N Symbol Source TITLE Application FAILURE Device or function user interface. 252 ISO 7000 n0026 AUTOMATIC CYCLE semi-automatic cycle Sequencing control function or Put automated sequencing control function in operation. 254 AUTO AUTOMATIC MODE Device main functions. The mode of operation when co
42、ntrol functions are not overridden by the user. Text could be put in a rectangular frame. 256 ISO 7000 n0017 AUTOMATIC CONTROL (closed loop) Control function 260 ISO 7000 n 96 MANUAL CONTROL Device, actuator or function mode. 262 ISO 7000 n 1627 DO NOT INTERVENE Do not intervene on device or output
43、actuating equipment. 302 IEC 60417-1 n 5184 CLOCK; TIME SWITCH; TIMER To identify terminals and controls related to clocks, time switches and timer. Start-stop function 304 IEC 60417-1 n 5440 PROGRAMMABLE TIMER, GENERAL To identify the control for a programmable timer, for instance the operating ele
44、ment for a programmable function. Start-stop function, change of operation mode. Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 13 N Symbol Source TITLE Description if source IEC 60417-1 Appl
45、ication AIR CIRCULATING FAN Ventilation function, ventilation equipment Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 22 N Symbol Source TITLE Description if source IEC 60417-1 Application L
46、IGHTING; ILLUMINATION To identify switches which control light source. Lighting 804 IEC 60417-1 n 5320 INDIRECT LIGHTING To identify a control for indirect lighting if a distinction from the symbol 5012 is necessary. Lighting 810 IEC 60417-1 n 5321 LOW INTENSITY LIGHTING To identify a control for lo
47、w intensity lighting if a distinction from the symbol 5012 is necessary. Lighting 812 IEC 60417-1 n 5056 BRIGHTNESS ; BRILLIANCE To identify the brightness control, for example of a light dimmer. Lighting 814 ISO 7000 n1142 WORKING LIGHT Lighting Licensed Copy: London South Bank University, South Ba
48、nk University, 31/01/2009 03:45, Uncontrolled Copy, (c) BSI DD CEN/TS 15810:2008 CEN/TS 15810:2008 (E) 23 N Symbol Source TITLE Description if source IEC 60417-1 Application & Comments 816 ISO 7000 n1700 SPOT LIGHT Lighting 818 ISO 7000 n1144 STAIRS LIGHT Lighting 820 ISO 7000 n1555 EXTERIOR BULB FA
49、ILURE Lighting 906 IEC 60417-1 n 5573 WATER TAP CLOSED To identify a closed water tap or connection or the control to close the water supply. Water tap closed 908 IEC 60417-1 n 5574 WATER TAP OPEN To identify an open water tap or the control to open up the water supply. Water tap open 910 IEC 60417-1 n 5582 SHOWER AND BATH Hot water equipment 912 WATER TANK Hot water equipment Licensed Copy: London South Bank University, South Bank University, 31/01/2009 03:45, Uncontrolled C