DD-IEC-PAS-61169-39-2008.pdf

《DD-IEC-PAS-61169-39-2008.pdf》由会员分享，可在线阅读，更多相关《DD-IEC-PAS-61169-39-2008.pdf（24页珍藏版）》请在三一文库上搜索。

1、DRAFT FOR DEVELOPMENT DD IEC/PAS 61169-39:2008 Radio-frequency connectors Part 39: Sectional specification for CQM series quick lock RF connectors ICS 33.120.30 ? Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI DD IEC/PAS 61169-39:2008 This Draft for Develo

2、pment was published under the authority of the Standards Policy and Strategy Committee on 30 June 2008 BSI 2008 ISBN 978 0 580 61965 6 National foreword This Draft for Development is the UK implementation of IEC/PAS 61169-39:2008. This publication is not to be regarded as a British Standard. It is b

3、eing issued in the Draft for Development series of publications and is of a provisional nature. It should be applied on this provisional basis, so that information and experience of its practical application can be obtained. A PAS is a Technical Specification not fulfilling the requirements for a st

4、andard, but made available to the public and established in an organization operating under a given procedure. A review of this Draft for Development will be carried out not later than three years after its publication. Notification of the start of the review period, with a request for the submissio

5、n of comments from users of this Draft for Development, will be made in an announcement in the appropriate issue of Update Standards. According to the replies received, the responsible BSI Committee will judge whether the validity of the PAS should be extended for a further three years or what other

6、 action should be taken and pass their comments on to the relevant international committee. Observations which it is felt should receive attention before the official call for comments will be welcomed. These should be sent to the Secretary of the responsible BSI Technical Committee at British Stand

7、ards House, 389 Chiswick High Road, London W4 4AL. The UK participation in its preparation was entrusted by Technical Committee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling, to Subcommittee EPL/46/2, Radio frequency connectors and

8、waveguides. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Amendments/corrigenda issued since publication Da

9、teComments Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI IEC/PAS 61169-39 Edition 1.0 2008-05 PUBLICLY AVAILABLE SPECIFICATION PRE-STANDARD Radio-frequency connectors Part 39: Sectional specification for CQM series quick lock RF connectors Licensed CopyCh

10、inese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI CONTENTS 1 2 3 3.1 3.1.1 3.1.2 3.2 3.2.1 3.3 3.3.1 3.3.2 4 4.1 4.2 4.3 4.3.1 4.3.2 4.4 4.4.1 4.4.2 5 5.1 5.2 5.3 5.4 5.5 5.6 5.7 Figure 6 Standard test connector with socket-centre contact (for dimensions, see 2 DD IEC/PAS 6

11、1169-39:2008 Scope.4 Normative reference.4 Mating interface and gauge information4 Dimensions General connectors Grade 2.5 Connector with pin centre contact.5 Connectors with socket-centre contact 6 Gauges .7 Connectors with socket-centre contact 7 Dimensions standard test connectors Grade 0.8 Conne

12、ctor with pin-centre contact8 Connector with socket-centre contact 9 Quality assessment procedure10 General.10 Rating and characteristics (see Clause 6 of IEC 61169-1/QC220000)10 Test schedule and inspection requirements.12 Acceptance tests .12 Periodic tests 13 Procedures14 Quality conformance insp

13、ection.14 Qualification approval and its maintenance14 Instructions for preparation of detail specifications .14 General.14 Identification of the detail specification14 Identification of the component15 Performance15 Marking, ordering information and related matters.15 Selection of tests, test condi

14、tions and severities15 Blank detail specification pro-forma for type CQM connector.16 Bibliography21 Figure 1 Connector with pin-centre contact (for dimensions, see Table 1).5 Figure 2 Connector with socket-centre contact (for dimensions, see Table 2) .6 Figure 3 Gauge for outer contact of socket co

15、nnector (for dimensions, see Table 3).7 Figure 4 Gauge pin for socket contact (for dimensions, see Table 4) 7 Figure 5 Connector of pin-centre contact (for dimensions, see Table 5) 8 Table 6) 9 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI 3 DD IEC/PAS 61

16、169-39:2008 Table 1 Dimensions of connector with pin-centre contact.5 Table 2 Dimensions of connector with socket-centre contact6 Table 3 Dimensions of gauge for outer contact of socket connector .7 Table 4 Dimensions of gauge pin for socket contact.8 Table 5 Dimensions of connector with pin-centre

17、contact.9 Table 6 Dimensions of standard test connector with socket-centre contact 10 Table 7 Ratings and characteristics .11 Table 8 Acceptance tests.12 Table 9 Periodic tests 13 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI RADIO-FREQUENCY CONNECTORS Pa

18、rt 39: Sectional specification for CQM series quick lock RF connectors 1 Scope CQM Series quick lock connectors with characteristic impedance 50 are used for high power microwave applications, connecting with RF cables or microstrips. The operating frequency limit is at least 4 GHz. This PAS is a se

19、ctional specification providing information and rules for the preparation of detail specifications for CQM series quick lock RF connectors together with the pro forma blank detail specification. It also prescribes mating interface dimensions for general purpose connectors, dimensional details of sta

20、ndard test connectors grade 0, gauging information and tests selected from QC 220000 (IEC 61169-1), applicable to all detail specifications relating to CQM series connectors. This specification indicates the recommended performance characteristics to be considered when writing a detail specification

21、 and it covers test schedules and inspection requirements for assessment levels M and H. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition

22、of the referenced document (including any amendments) applies. IEC 61169-1:1992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods1) Amendment 1 (1996) Amendment 2 (1997) 3 Mating interface and gauge information All undimensioned pictorial configurat

23、ions are for reference purposes only. 1) A consolidated edition 1.2 (1998) exists, that comprises IEC 61169-1 (1992), Amendment 1 and Amendment 2. 4 DD IEC/PAS 61169-39:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI 3.1 Dimensions General connectors G

24、rade 2 3.1.1 Connector with pin centre contact Note 1 Note 2 Note 4 R1.5+0.1 0 Note 3 p m n h i b a s e c d l f g k j u v t Figure 1 Connector with pin-centre contact (for dimensions, see Table 1) Table 1 Dimensions of connector with pin-centre contact Ref. mm Notes a 5,96 6,04 Diameter b 7 (nominal

25、) Diameter c 15,85 16,25 Diameter d 16,90 17,10 Diameter e 18,00 18,20 Diameter f 21,00 21,20 Diameter g 21,90 22,10 Diameter h 8,90 9,20 i 3,70 3,90 j 4,30 4,50 k 9,80 l 0,30 0,50 m 8,80 9,00 n 7,20 7,40 s 23,20 23,30 Diameter t 35,00 35,20 Diameter p 4,20 4,40 u 2,10 2,30 v 26,9 27,2 Diameter NOTE

26、 1 Mechanical reference plane. NOTE 2 The spring force is 50 N to 60 N max. NOTE 3 Tolerances of dimensions are to meet the requirements of characteristic impedances. NOTE 4 Ring. 5 DD IEC/PAS 61169-39:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI 3.

27、1.2 Connectors with socket-centre contact Note 6 Note 5 Note 4 1.5 45 Note 3 Note 2 Note 1 g f u i j h n e m a b c d q p l k rs Figure 2 Connector with socket-centre contact (for dimensions, see Table 2) Table 2 Dimensions of connector with socket-centre contact mm Ref. min max Notes a 7（nominal） 1

28、b 15,85 16,25 c 16,70 16,90 d 17,80 18,00 e 22,10 22,30 f 6,30 6,50 g 9,10 9,30 h 12,75 12,85 i 0,20 0,40 j 0,20 k 7,00 7,50 l 8,50 9,00 m 23,60 23,80 n 35,20 35,40 p 0,80 1,00 q 1,10 1,30 r 1,60 s 2,60 u 4,90 5,20 NOTE 1 Design for slotting optional, closed contacts should meet electrical and mecha

29、nical requirements. NOTE 2 Design for slotting optical, flared contacts c should be flared to 18,418,5. NOTE 3 Mechanical reference plane. NOTE 4 Three steel balls, 3; NOTE 5 The spring force is 2 N to 6 N, treval is 1,60 mm min. NOTE 6 Ring. 6 DD IEC/PAS 61169-39:2008 Licensed CopyChinese Universit

30、y of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI 3.2 Gauges 3.2.1 Connectors with socket-centre contact 3.2.1.1 Gauge for outer contact of socket connector Figure 3 Gauge for outer contact of socket connector (for dimensions, see Table 3) Table 3 Dimensions of gauge for outer contact of

31、socket connector Gauge A (for sizing purposes) Gauge B (for measurement of gauge retention force for outer conductor) Mass (weight) of gauge: 200 g 5 g mm mm Ref. min max min max Notes s 18,05 18,10 18,15 18,18 t 18,70 18,80 18,70 18,80 u 20,00 20,80 20,00 20,80 v 9,50 9,60 9,40 9,50 w 1,30 1,50 1,3

32、0 1,50 NOTE Material: steel, polished, surface roughness: Ra0,4 m. 3.2.1.2 Test sequence Gauge A shall be placed over the outer contact of the connector once. This is a sizing operation. After this, gauge B shall be placed over the outer contact in a vertical position. The gauge shall be retained. T

33、his test can also be carried out on connector. 3.2.1.3 Gauge pin for socket-centre contact (0.2992in) (0.2205min) a 5.6mm min 7.6mm max Figure 4 Gauge pin for socket contact (for dimensions, see Table 4) 7 DD IEC/PAS 61169-39:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncon

34、trolled Copy, (c) BSI Table 4 Dimensions of gauge pin for socket contact Gauge C (for sizing purposes) Gauge D (for measurement of gauge retention force for centre contact) Mass (weight) of gauge: 600 g 5 g mm mm Ref. min max min max a 6,05 6,10 5,95 6,00 NOTE Material: steel, polished, surface roug

35、hness: Ra0,4 m. 3.2.1.4 Test sequence Test pin gauge C shall be inserted into the centre contact three times with a minimum depth of 5,6 mm. This is a sizing operation and should only be carried out when the socket centre contact is removed from the connector. After this, gauge D shall be inserted a

36、nd held in the vertical position. The gauge shall be retained. This test can also be carried out on connector when the socket centre contact is not removed. 3.3 Dimensions standard test connectors Grade 0 3.3.1 Connector with pin-centre contact y x a b j k g t f l n m p d c e s i h v Note 1Note 3 R1

37、.5+0.1 0 Note 2 B A 0.05mm 0.002inB 0.05mm 0.002inA R0.5 108 u Figure 5 Connector of pin-centre contact (for dimensions, see Table 5) 8 DD IEC/PAS 61169-39:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI Table 5 Dimensions of connector with pin-centre

38、contact mm Ref. min max Notes a 5,99 6,00 Diameter b 6,97 6,98 Diameter c 16,05 16,07 Diameter d 16,96 17,04 Diameter e 18,05 18,15 Diameter f 21,05 21,15 Diameter g 21,95 22,05 Diameter h 9,02 9,08 i 3,77 3,83 j 4,35 4,45 k 9,70 9,80 l 0,30 0,50 m 8,86 8,94 n 7,27 7,33 s 22,20 22,25 Diameter t 23,0

39、4 23,10 Diameter u 2,15 2,25 v 27,00 27,10 Diameter x 4,20 4,40 y 7,20 7,40 NOTE 1 Mechanical reference plane. NOTE 2 The spring force is 50 N to 60 N. NOTE 3 Ring. 3.3.2 Connector with socket-centre contact g u h j if d c b m e n rs p q w v R0.3 Note 5 Note 6 Note 3 Note 1 Note 2 Note 4 1.545 0.05m

40、m 0.002inA x y Figure 6 Standard test connector with socket-centre contact (for dimensions, see Table 6) 9 DD IEC/PAS 61169-39:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI Table 6 Dimensions of standard test connector with socket-centre contact Ref.

41、 mm Notes min max b 16,05 16,07 c 16,92 16,96 d 18,01 18,05 e 22,18 22,25 f 6,35 6,42 g 9,18 9,25 h 12,78 12,81 i 0,28 0,32 j 0,20 m 23,68 23,75 n 35,25 35,35 p 0,88 0,96 q 1,06 1,14 r 1,60 s 2,60 u 4,95 5,05 w 6,97 7,00 x 7,00 7,20 y 8,50 9,00 NOTE 1 Three steel balls, 3. NOTE 2 Design for slotting

42、 optional, flared contacts c should be flared to 18,40 18,50. NOTE 3 Mechanical reference plane. NOTE 4 When a gauge pin with diameter of 5,99 mm min 6 mm max is inserted into a depth of 5,00 mm min dimension, v should meet the requirements of dimension w. NOTE 5 The spring force is 2 N to 6 N, trev

43、al is 1,60 mm min. NOTE 6 Ring. 4 Quality assessment procedure 4.1 General The following clauses provide recommended rating, performance and test conditions to be considered when writing a detail specification. They also provide an appropriate schedule of tests with minimum levels of conformance ins

44、pection sampling, together with the pro forma blank detail specification (BDS) and instructions for the preparation of a detail specification. 4.2 Rating and characteristics (see Clause 6 of IEC 61169-1/QC220000) The values indicated below (see Table 7) are recommended for CQM series quick lock conn

45、ectors and are given for the writer of the detail specification. They are applicable for the condition when the connectors are fully mated. Certain tests are listed without any recommended values being given. These tests will usually not be required. When these tests are required, appropriate values

46、 shall be entered in the detail specification at the discretion of the specification writer. 10 DD IEC/PAS 61169-39:2008 Licensed CopyChinese University of Hong Kong, 20/10/2008 09:22, Uncontrolled Copy, (c) BSI Table 7 Ratings and characteristics Ratings and characteristics IEC 61169-1 Subclause Va

47、lue Remarks including any deviations from standard test methods Electrical Nominal impedance 50 Frequency range Grade 2 connectors Up to 4 GHz Or upper frequency limit of the cable Reflection factor 49.2.14. straight styles 1) 7 5 G after conditioning 500 M Proof voltage at sea level 2) 3) .9.2.6 2

48、700 V (86106 kPa) Proof voltage at 4,4 kPa 2) 3) .9.2.6 350 V 4,4 kPa approximately equivalent to 20 km Environmental test voltage at sea level3) 4 9. .9.4.63.3 2 000 V (86106 kPa) Screening effectiveness7) .9.2.8 90 dB to 1 GHz Zt 1 000 V Extinction voltage Mechanical Centre contact captivation axial force torque 9.3.5 15 N, 1 min N/A6) Maximum displacement 0,25 mm each direction Engagement and separation force engagement force separation force 9.3.6 6 N 2 N s Mechanical tests on cable fixing Cable pulling cable rotation (nutat