《IEC-60384-19-1-2006.pdf》由会员分享，可在线阅读，更多相关《IEC-60384-19-1-2006.pdf（20页珍藏版）》请在三一文库上搜索。
1、 INTERNATIONAL STANDARD IEC 60384-19-1 QC 302201 Second edition 2006-01 Fixed capacitors for use in electronic equipment Part 19-1: Blank detail specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors Assessment level EZ Reference number IEC 60384-19-1
2、:2006(E) Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbe
3、rs 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus
4、 ensuring that the content reflects current technology. Information relating to this publication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in
5、progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you t
6、o search by a variety of criteria including text searches, technical committees and date of publication. On-line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications
7、(www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: cu
8、stserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 60384-19-1 QC 302201 Second edition 2006-01 Fixed capacitors for use in electronic equipment Part 19-1: Blank detail specification Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capaci
9、tors Assessment level EZ IEC 2006 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Co
10、mmission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch M For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale International Electrotechnical Commission 2 60384
11、-19-1 IEC:2006(E) INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 19-1: Blank detail specification Fixed metallized polyethylene- terephthalate film dielectric surface mount d.c. capacitors Assessment level EZ FOREWORD 1) The International Electrotec
12、hnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To th
13、is end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National
14、 Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO)
15、 in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation fro
16、m all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be he
17、ld responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any d
18、ivergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publicati
19、on. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property
20、 damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this
21、 publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or
22、all such patent rights. International Standard IEC 60384-19-1 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. This second edition cancels and replaces the first edition published in 1993 and constitutes minor revisions related to tables, figures an
23、d references. The text of this standard is based on the following documents: FDIS Report on voting 40/1623/FDIS 40/1646/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accorda
24、nce with the ISO/IEC Directives, Part 2. 60384-19-1 IEC:2006(E) 3 IEC 60384 consists of the following parts, under the general title Fixed capacitors for use in electronic equipment: Part 1: Generic specification Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film diele
25、ctric d.c. capacitors Part 3: Sectional specification: Fixed tantalum surface mount capacitors Part 4: Sectional specification: Aluminium electrolytic capacitors with solid and non-solid electrolyte Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage not excee
26、ding 3000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate film dielectric d.c. capacitors Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1 Part 9: Sectional specification: Fixed capacitors of cera
27、mic dielectric, Class 2 Part 11: Sectional specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors Part 13: Sectional specification: Fixed polypropylene film dielectric
28、 metal foil d.c. capacitors Part 14: Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte Part 16: Sectional specification: Fixed metal
29、lized polypropylene film dielectric d.c. capacitors Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors Part 18: Sectional specification: Fixed aluminium electrolytic surface mount capacitors with solid and non-solid electrolyte Part 19: Section
30、al specification: Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors Part 20: Sectional specification: Fixed metallized polyphenylene sulfide film dielectric surface mount d.c. capacitors Part 21: Sectional specification: Fixed surface mount multilayer capacito
31、rs of ceramic dielectric, Class 1 Part 22: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2 Part 23: Sectional specification Fixed surface mount metallized polyethylene naphthalate film dielectric DC capacitors Part 24: Sectional specification Surface
32、 mount fixed tantalum electrolytic capacitors with conductive polymer solid electrolyte 1 Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte1 The QC number that appears on the front cover of this publication is the specifi
33、cation number in the IECQ Quality Assessment System for Electronic Components. _ 1 To be published. 4 60384-19-1 IEC:2006(E) The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec
34、.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual edition of this blank detail specification may be issued at a later date. 60384-19-1 IEC:2006(E) 5 FIXED CAPACITORS FOR USE IN EL
35、ECTRONIC EQUIPMENT Part 19-1: Blank detail specification Fixed metallized polyethylene- terephthalate film dielectric surface mount d.c. capacitors Assessment level EZ Blank detail specification A blank detail specification is a supplementary document to the sectional specification and contains requ
36、irements for style and layout and minimum content of detail specifications. Detail specifications not complying with these requirements may not be considered as being in accordance with IEC specifications nor shall they so be described. In the preparation of detail specifications, the content of 1.4
37、 of the sectional specification shall be taken into account. The numbers between brackets on the first page correspond to the following information which shall be inserted in the position indicated. Identification of the detail specification 1 The “International Electrotechnical Commission“ or the N
38、ational Standards Organization under whose authority the detail specification is drafted. 2 The IEC or National Standards number of the detail specification, date of issue and any further information required by the national system. 3 The number and issue number of the IEC or national generic specif
39、ication. 4 The IEC number of the blank detail specification. Identification of the capacitor 5 A short description of the type of capacitor. 6 Information on typical construction (when applicable). When the capacitor is not designed for use in printed-board applications, this shall be clearly stated
40、 in the detail specification in this position. 7 Outline drawing with main dimensions which are of importance for interchangeability and/or reference to the national or international documents for outlines. Alternatively, this drawing may be given in an annex to the detail specification. 8 Applicati
41、on or group of applications covered and/or assessment level. NOTE The assessment level(s) to be used in a detail specification are selected from 3.5.4 of the sectional specification. This implies that one blank detail specification may be used in combination with several assessment levels, provided
42、the grouping of the tests does not change. 9 Reference data on the most important properties, to allow comparison between the various capacitor types. 6 60384-19-1 IEC:2006(E) 1 IEC 60384-19-1-XXX 2 QC 302201-XXX IEC 60384-19-1 4 QC 302201 ELECTRONIC COMPONENTS OF ASSESSED QUALITY IN ACCORDANCE WITH
43、: 3 FIXED METALLIZED 5 POLYETHYLENE-TEREPHTHALATE FILM DIELECTRIC DC SURFACE MOUNT CAPACITORS 6 Outline drawing: (see Table 1) .angle projection 7 Other shapes are permitted within the dimensions given. Assessment level(s): EZ 8 Information on the availability of components qualified to this detail
44、specification is given in IEC QC 001005 (9) 1 General data 1.1 Recommended method(s) of mounting (to be inserted) See IEC 60384-19, 1.4.2 1.2 Dimensions Table 1 Case size reference and dimensions Dimensions mm Case size reference L1 max W1 max H1 max L2 L3 L4 min When there is no case size reference
45、, Table 1 may be omitted and the dimensions shall be given in Table 2, which then becomes Table 1. The dimensions shall be given as maximum dimensions or as nominal dimensions with a tolerance. 60384-19-1 IEC:2006(E) 7 1.3 Ratings and characteristics Capacitance range (see Table 2) Tolerance on rate
46、d capacitance Rated voltage (see Table 2) Category voltage (if applicable) (see Table 2) Climatic category Rated temperature Max. a.c. voltage (if applicable) Max. pulse load (if applicable) Tangent of loss angle Insulation resistance Table 2 Values of capacitance and of voltage related to case size
47、s Rated voltage Category voltagea Case size Case size Case size Case size Rated capacitance (in nF and/or F) a If different from the rated voltage. 1.4 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the editi
48、on cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60384-1, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60384-19, Fixed capacitors for use in electronic equipment Part 19: Sectional sp
49、ecification Fixed metallized polyethylene-terephthalate film dielectric surface mount d.c. capacitors IEC 60410, Sampling plans and procedures for inspection by attributes 1.5 Marking The marking of the capacitor and the package shall be in accordance with the requirements of IEC 60384-19, 1.6. The details of the marking of the component and package shall be given in f