《IEC-62425-2007.pdf》由会员分享，可在线阅读，更多相关《IEC-62425-2007.pdf（198页珍藏版）》请在三一文库上搜索。
1、 IEC 62425 Edition 1.0 2007-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Railway applications Communication, signalling and processing systems Safety related electronic systems for signalling Applications ferroviaires Systmes de signalisation, de tlcommunications et de traitement Systmes lectroniq
2、ues de scurit pour la signalisation IEC 62425:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, includi
3、ng photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
4、your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les
5、microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de vo
6、tre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, ele
7、ctronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. ? Catalogue of IEC publications: www.iec.ch/searchpu
8、b The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. ? IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Jus
9、t Published details twice a month all new publications released. Available on-line and also by email. ? Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent
10、terms in additional languages. Also known as the International Electrotechnical Vocabulary online. ? Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us:
11、Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes.
12、A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. ? Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue
13、en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. ? Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouve
14、lles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. ? Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et
15、dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. ? Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette public
16、ation ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62425 Edition 1.0 2007-09 INTERNATIONAL STANDARD NORME INTERNATIONALE Railway applications Communication, signalling and processing systems Safet
17、y related electronic systems for signalling Applications ferroviaires Systmes de signalisation, de tlcommunications et de traitement Systmes lectroniques de scurit pour la signalisation INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XD ICS 45.060 PRICE CODE CODE
18、 PRIX ISBN 2-8318-9310-0 2 62425 IEC:2007 CONTENTS FOREWORD.5 INTRODUCTION.7 1 Scope.8 2 Normative references9 3 Terms, definitions and abbreviations.10 3.1 Definitions .10 3.2 Abbreviations.15 4 Overall framework of this standard16 5 Conditions for safety acceptance and approval17 5.1 The safety ca
19、se .17 5.2 Evidence of quality management19 5.3 Evidence of safety management 21 5.3.1 Introduction .21 5.3.2 Safety life-cycle .22 5.3.3 Safety organisation 23 5.3.4 Safety plan 24 5.3.5 Hazard log.25 5.3.6 Safety requirements specification.25 5.3.7 System/sub-system/equipment design25 5.3.8 Safety
20、 reviews .25 5.3.9 Safety verification and validation 25 5.3.10 Safety justification26 5.3.11 System/sub-system/equipment handover26 5.3.12 Operation and maintenance .26 5.3.13 Decommissioning and disposal 26 5.4 Evidence of functional and technical safety 26 5.5 Safety acceptance and approval 29 5.
21、5.1 Introduction .29 5.5.2 Safety approval process.30 5.5.3 After safety approval32 5.5.4 Dependency between safety approvals.32 Annex A (normative) Safety integrity levels.33 Annex B (normative) Detailed technical requirements .47 Annex C (normative) Identification of hardware component failure mod
22、es .62 Annex D (informative) Supplementary technical information79 Annex E (informative) Techniques and measures for safety-related electronic systems for signalling for the avoidance of systematic faults and the control of random and systematic faults .86 Bibliography95 Figure 1 Scope of the main I
23、EC railway application standards.9 Figure 2 Structure of IEC 62425 .17 62425 IEC:2007 3 Figure 3 Structure of safety case19 Figure 4 Example of system life-cycle (from IEC 62278) .21 Figure 5 Example of design and validation portion of system life-cycle 23 Figure 6 Arrangements for independence .24
24、Figure 7 Structure of technical safety report29 Figure 8 Typical safety acceptance and approval process.31 Figure 9 Examples of dependencies between safety cases/safety approval.32 Figure A.1 Safety requirements and safety integrity 34 Figure A.2 Global process overview36 Figure A.3 Example risk ana
25、lysis process.37 Figure A.4 Definition of hazards with respect to the system boundary38 Figure A.5 Example hazard control process40 Figure A.6 Interpretation of failure and repair times 41 Figure A.7 Treatment of functional independence by FTA .42 Figure A.8 Relationship between SILs and techniques
26、45 Figure B.1 Influences affecting the independence of items52 Figure B.2 Detection and negation of single faults.55 Figure C.1 Example of a 4-terminal resistor, using a hybrid thick layer technique 65 Figure D.1 Example of a fault analysis method .83 Table A.1 SIL-table 45 Table C.1 Resistors68 Tab
27、le C.2 Capacitors69 Table C.3 Electromagnetic components69 Table C.4 Diodes .71 Table C.5 Transistors.72 Table C.6 Controlled rectifiers 73 Table C.7 Surge suppressors .74 Table C.8 Opto-electronic components.75 Table C.9 Filters.76 Table C.10 Interconnection assemblies 76 Table C.11 Fuses.77 Table
28、C.12 Switches and push/pull buttons.77 Table C.13 Lamps77 Table C.14 Batteries.78 Table C.15 Transducers/sensors (not including those with internal electronic circuitry)78 Table C.16 Integrated circuits.78 Table D.1 Examples of measures to detect faults in large-scale integrated circuits by means of
29、 periodic on-line testing, with comparison (SW or HW), in a 2-out-of-n system 84 Table E.1 Safety planning and quality assurance activities (referred to in 5.2 and 5.3.4)88 Table E.2 System requirements specification (referred to in 5.3.6).88 Table E.3 Safety organisation (referred to in 5.3.3) .89
30、Table E.4 Architecture of system/sub-system/equipment (referred to in 5.4).89 4 62425 IEC:2007 Table E.5 Design features (referred to in 5.4) 90 Table E.6 Failure and hazard analysis methods (referred to in 5.4) .91 Table E.7 Design and development of system/sub-system/equipment (referred to in 5.3.
31、7)91 Table E.8 Design phase documentation (referred to in 5.2).92 Table E.9 Verification and validation of the system and product design (referred to in 5.3.9)93 Table E.10 Application, operation and maintenance (referred to in 5.3.12 and 5.4).94 62425 IEC:2007 5 INTERNATIONAL ELECTROTECHNICAL COMMI
32、SSION _ RAILWAY APPLICATIONS COMMUNICATION, SIGNALLING AND PROCESSING SYSTEMS SAFETY RELATED ELECTRONIC SYSTEMS FOR SIGNALLING FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC Nati
33、onal Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publi
34、cly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- govern
35、mental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on
36、 technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted
37、 by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international
38、uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter
39、. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its dire
40、ctors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arisin
41、g out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is dr
42、awn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62425 has been prepared by IEC technical committee 9: Electrical equipment and sys
43、tems for railways. It was submitted to the National Committees for voting under the Fast Track Procedure as the following documents: FDIS Report on voting 9/1057/FDIS 9/1087/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the abo
44、ve table. This document is based on EN 50129. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. 6 62425 IEC:2007 The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site un
45、der “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 62425 IEC:2007 7 INTRODUCTION This standard is the first International Standard defining requirements for the acceptan
46、ce and approval of safety-related electronic systems in the railway signalling field. This standard is derived from the European Standard EN 50129. Safety-related electronic systems for signalling include hardware and software aspects. To install complete safety-related systems, both parts within th
47、e whole life-cycle of the system have to be taken into account. The requirements for safety-related hardware and for the overall system are defined in this standard. Other requirements are defined in associated IEC standards. This standard is the common base for safety acceptance and approval of ele
48、ctronic systems for railway signalling applications. The aim of railway authorities and railway industry is to develop railway systems based on common standards. The safety authorities having jurisdiction can apply this standard to the relevant matters they choose. On this basis, cross- acceptance o
49、f safety approvals for sub-systems and equipment can be applied by the different national safety authorities. Cross-acceptance is applicable to generic approval, not to specific applications. The standard consists of the main part (Clause 1 to Clause 5) and Annexes A, B, C, D and E. The requirements defined in the main part of t