《IEEE standard for receiver fixture interface.pdf》由会员分享，可在线阅读，更多相关《IEEE standard for receiver fixture interface.pdf（138页珍藏版）》请在三一文库上搜索。
1、IEEE Std 1505-2006 IEEE Standard for Receiver Fixture Interface I E E E 3 Park Avenue New York, NY 10016-5997, USA 16 April 2007 IEEE Standards Coordinating Committee 20 Sponsored by the IEEE Standards Coordinating Committee 20 on Test and Diagnosis for Electronic Systems Recognized as an American N
2、ational Standard (ANSI) IEEE Std 1505-2006 IEEE Standard for Receiver Fixture Interface Sponsor IEEE Standards Coordinating Committee 20 on Test and Diagnosis for Electron Systems Approved 7 August 2006 IEEE SA-Standards Board Approved 19 October 2006 American National Standards Institute The Instit
3、ute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2007 by the Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 16 April 2007. Printed in the United States of America. IEEE is a registered trademark in the U.S
4、. Patent and b) to develop within this framework a defined set(s) of interconnecting connector and mechanical specifications that supports available, accepted, low- cost commercial technology to reduced dependence on proprietary designs, and extend life- cycle availability. Keywords: connector, fixt
5、ure, framework, interface, interoperability, mass-interconnect, quick disconnect, receiver, specification IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating Committees of the IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its stan
6、dards through a consensus development process, approved by the American National Standards Institute, which brings together volunteers representing varied viewpoints and interests to achieve the final product. Volunteers are not necessarily members of the Institute and serve without compensation. Wh
7、ile the IEEE administers the process and establishes rules to promote fairness in the consensus development process, the IEEE does not independently evaluate, test, or verify the accuracy of any of the information contained in its standards. Use of an IEEE Standard is wholly voluntary. The IEEE disc
8、laims liability for any personal injury, property or other damage, of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, or reliance upon this, or any other IEEE Standard document. The IEEE does not warrant
9、 or represent the accuracy or content of the material contained herein, and expressly disclaims any express or implied warranty, including any implied warranty of merchantability or fitness for a spe- cific purpose, or that the use of the material contained herein is free from patent infringement. I
10、EEE Standards documents are supplied “AS IS.” The existence of an IEEE Standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE Standard. Furthermore, the viewpoint expressed at the time a s
11、tandard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. Every IEEE Standard is subjected to review at least every five years for revision or reaffirmation. When a document is more than five years
12、 old and has not been reaffirmed, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine that they have the latest edition of any IEEE Standard. In publishing and making this document
13、 available, the IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity. Nor is the IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing this, and any other IEEE Standards document, should rely
14、upon the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Interpretations: Occasionally questions may arise regarding the meaning of portions of standards as they relate to specific applications. When the need for interpretations is brough
15、t to the attention of IEEE, the Institute will initiate action to prepare appropriate responses. Since IEEE Standards represent a consensus of concerned interests, it is important to ensure that any interpretation has also received the concurrence of a balance of interests. For this reason, IEEE and
16、 the members of its societies and Standards Coordinating Committees are not able to provide an instant response to interpretation requests except in those cases where the matter has previously received formal consideration. At lectures, symposia, seminars, or educational courses, an individual prese
17、nting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the formal position, explanation, or interpretation of the IEEE. Comments for revision of IEEE Standards are welcome from any interested party, regardl
18、ess of membership affil- iation with IEEE. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Comments on standards and requests for interpretations should be addressed to: Secretary, IEEE-SA Standards Board 445 Hoe
19、s Lane Piscataway, NJ 08854 USA Authorization to photocopy portions of any individual standard for internal or personal use is granted by the Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright Clearance Center. To arrange for payment of li
20、censing fee, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. ivCopyright 200
21、7 IEEE. All rights reserved. Introduction Historical Background On September 19, 1996, a group of receiver fixture product vendors/integrators announced the formation of an industry standards group called the RFI Alliance. The organization later sought to gain identity through a standards organizati
22、on, which ultimately became the Institute of Electrical and Electronic Engineers, Inc. Under the joint sponsorship of the Instrumentation and Measurement Society and SCC-20 Subcommittee of the Computer Society, a PAR 1505 Standard Working Group was developed and authorized by the IEEE Standards Asso
23、ciation. Participation in the IEEE Std 1505 RFI Working Group is open to vendors, integrators and users. IEEE Std 1505 Receiver Fixture Interface Working Group focus The IEEE Std 1505 RFI Working Group sponsored by the IEEE Instrumentation and Measurement Society and the IEEE SCC-20 Technical Commit
24、tee was formed to define a common electrical/mechanical interface specifications for applications involving test, production processing, quick-disconnect electrical interfacing, and subassembly mating requirements. The group is made up of technical individuals from industry, govern- ment, and academ
25、ia, which reflect perspective views of a supplier, user, and general interest in the standard. To derive these specifications, the IEEE Std 1505 Working Group utilized the results of a study conducted by the Department of Defense Automatic Test System Research and (b) Annex B “Automatic Test System
26、Critical Interfaces Report, dated 9/30/96” B27, the results of a study conducted by the Department of Defense Automatic Test System Research and Development 1The number in brackets correspond to those of the bibliography in Annex C. IEEE Std 1505-2006IEEE STANDARD FOR 2Copyright 2007 IEEE. All right
27、s reserved. Integrated Product Team (ARI) Critical Interface Working Group (CIWG), which reviewed as part of their tasks the ATS test interface. 1.2 Purpose The purpose of this standard is to permit interchangeability of mechanical/electrical receiver/fixture/connec- tor product assemblies from vari
28、ous manufacturers under an “open architecture.” To develop within this framework, a defined set(s) of interconnecting connector and mechanical specifications that supports avail- able, accepted, low-cost commercial technology to reduce dependence on proprietary designs and extends life-cycle availab
29、ility. Technical requirements identified by government and industry include maximum flexibility, scalability, and range of application. 2. Normative references The following referenced documents are indispensable for the application of this document. For dated refer- ences, only the edition cited ap
30、plies. For undated references, the latest edition of the referenced document (including any amendments or corrigenda) applies. ANSI B46 Surface Texture (Surface Roughness Waviness and Lay).2 ANSI/NCSL Z540-1 Laboratories, Calibration, and Measuring and Test Equipment. ASTM A240, ASTM A666, ASTM A693
31、 Steel Plates, Sheets and Strip-Corrosion Resisting.3 ASTM A342 Indicator, Permeability, Low-Mu (GoNo Go). ASTM A484 Steel Products Wrought Stainless and Heat Resisting General Requirements. ASTM A581 Steel Wire Free Machining Stainless and Heat Resistant. ASTM A582 Free Machining Stainless and Heat
32、 Resisting Steel Bars, Hot Rolled or Cold Finished. ASTM A967, SAE AMS QQ-P-35 Passivation Treatment for Austenitic, Ferritic, and Martensitic Corrosion-Resistant Steel (Fastening Devices). ASTM B103 Phosphor Bronze Plate, Sheet Strip and Rolled Bar Specification. ASTM B121/B12M, QQ-B-613 Brass, Lea
33、ded/Non-Leaded; Flat Products. ASTM B134 Brass Wire. ASTM B139, QQ-B-750 Bronze, Phosphor, Bar, Plate, Rod, Sheet, Strip, Flat Wire, and Structural and Spe- cial Shaped Sections. ASTM B159 Wire Phosphor Bronze. ASTM B16 Rod, Brass, Free-Cutting, Bar and Shapes for Use in Screw Machines. 2ANSI public
34、ations are available from the Sales Department, American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA (http:/www.ansi.org/). 3ASTM publications are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken, PA 194
35、28-2959, USA (http:/www.astm.org/). IEEE RECEIVER FIXTURE INTERFACEStd 1505-2006 Copyright 2007 IEEE. All rights reserved.3 ASTM B194, QQ-C-530 Copper-Beryllium Alloy Bar/Rod/Wire (Copper Alloy Numbers 172/173). ASTM B194, QQ-C-533 Copper-Beryllium Alloy Strip (Copper Alloy Numbers 170 and 172). AST
36、M B196 Rod and Bar, Copper-Beryllium Alloy. ASTM B197 Wire, Alloy Copper-Beryllium. ASTM B206/B206M, QQ-W-321 Wire, Copper Alloy. ASTM B209, QQ-A-250/11 Aluminum Alloy 6061, Plate and Sheet. ASTM B209, QQ-A-250/12 Aluminum Allow 7075, Plate and Sheet. ASTM B209, QQ-A-250/2 Aluminum Alloy 3003 Plate
37、and Sheet. ASTM B209, QQ-A-250/4 Aluminum Alloy 2024 Plate and Sheet. ASTM B209, QQ-A-250/8 Aluminum Alloy 5052 Plate and Sheet. ASTM B209, SAE-AMS-QQ-A-250/1 -Aluminum Alloy 1100 Plate and Sheet. ASTM B301 Free Cutting Copper Rod and Bar. ASTM B36 Plate, Brass, Sheet, Strip, and Rolled Bar. ASTM B4
38、41 Copper Cobalt Beryllium Rod and Bar. ASTM B488 Gold for Engineering Uses, Electrodeposited Coatings of. ASTM B740 CDA 72,900 Copper Nickel Tin Alloy. ASTM D4067 Gold Plating, Electrodeposited. ASTM D5927 Thermoplastic Polyester (TPES) Injection and Extrusion Materials Based on ISO Test, Methods,
39、Standard Specification for. ASTM D5948, Type SDG-F Molding Plastics and Molded Plastic Parts, Thermosetting. ASTM-B121/B12M, QQ-B-626 Brass, Leaded/Non-Leaded; Rod/Shapes/Forgings/Flat Products with Fin- ished Edges (Bar and Strip). EIA 364, MIL-STD-1344A Test Methods for Electrical Connectors. EIA
40、557 Statistical Process Control Systems.4 Electrical Safety-Related Work Practices Inspection Procedures and Interpretation Guidelines. STD 01-16-007 STD 1-16.7 (1991, July 1). 4EIA publications are available from Global Engineering Documents, 15 Inverness Way East, Englewood, CO 80112, USA (http:/
41、IEEE Std 1505-2006IEEE STANDARD FOR 4Copyright 2007 IEEE. All rights reserved. Enforcement of the Electrical Power Generation, Transmission, and Distribution Standard. CPL 02-01-038 CPL 2-1.38 (2002, October 31).5 FED-STD-H28 Screw Thread Standards for Federal Services. IEC 309-1 Plugs, socket-outle
42、ts and couplers for industrial purposesPart 1.6 IEEE Standards Style Manual, July 2005.7 IEEE/ASTM SI 10, American National Standard for Use of the International System of Units (SI). Inspection Guidelines for 29 CFR 1910. STD 01-06-006 STD 1-6.6 (1995, June 16). IPC-D-275 Design Standard for Rigid
43、Printed Boards and Rigid Printed Board Assemblies. ISO 10012-1 Equipment, Quality Assurance Requirements for Measuring, Part 1: Meteorological Confirma- tion System for Measuring Equipment. ISO 9001 Quality Systems Model for quality assurance in design/development, production, installation and servi
44、cing.8 MIL -F-14072 Finishes for Ground Electronic Equipment. MIL-C-24308 Filter Connectors. MIL-C-83517 Connector, Coaxial, RF for Coaxial, Strip or Microstrip Transmission Line. MIL-C-83517 SMA Series Coaxial Connectors. MIL-DTL-16878/1 Wire, Electrical, Insulated, High TemperatureGeneral Requirem
45、ents for.9 MIL-DTL-55302 Connectors, Printed Circuit Subassembly and Accessories. MIL-DTL-55330 Connectors, Electrical and Fiber Optic, Packaging of. MIL-HDBK-217 Reliability Prediction of Electronic Equipment. MIL-HDBK-454A/4 General Guidelines for Electronic Equipment. MIL-M-24519 Molding Plastics
46、, Polyester Thermoplastic, Polyarylether Thermoplastic, Plastic Molding Material, Polyphenylene Sulfide, Glass Fiber Reinforced. 5U.S. Regulatory Guides are available from the Superintendent of Documents, U.S. Government Printing Office, P.O. Box 37082, Washington, DC 20013-7082, USA (http:/www.acce
47、ss.gpo.gov/). 6IEC publications are available from the Sales Department of the International Electrotechnical Commission, Case Postale 131, 3, rue de Varemb, CH-1211, Genve 20, Switzerland/Suisse (http:/www.iec.ch/). IEC publications are also available in the United States from the Sales Department,
48、 American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA (http:/ www.ansi.org/). 7These publications are available from the Institute of Electrical and Electronics Engineers, Inc., 445 Hoes Lane, Piscataway, NJ 08854, USA (http:/standards.ieee.org/). 8ISO publi
49、cations are available from the ISO Central Secretariat, Case Postale 56, 1 rue de Varemb, CH-1211, Genve 20, Switzer- land/ Suisse (http:/www.iso.ch/). ISO publications are also available in the United States from the Sales Department, American National Standards Institute, 25 West 43rd Street, 4th Floor, New York, NY 10036, USA (http:/www.ansi.org/). 9Copies of specifications, standards, drawings, and publications required by manufacturers in connection with specific procurement functions may be obtained from the U.S.Government Printing