《BS-6272-1982 EN-50042-1980.pdf》由会员分享，可在线阅读，更多相关《BS-6272-1982 EN-50042-1980.pdf（14页珍藏版）》请在三一文库上搜索。
1、BRITISH STANDARD BS 6272:1982 EN 50 042 Specification for Low voltage switchgear and controlgear for industrial use Terminal marking Terminals for external associated electronic circuit components and contacts This European Standard EN 50 042 was given as from 30 September 1982 the status of a Briti
2、sh Standard UDC 621.316.54:621.3.027.2:621.315.684:003.62 Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6272:1982 This British Standard was published under the authority of the Board of BSI and comes into effect on 30 September 1982 BSI
3、 07-1999 The following BSI references relate to the work on this standard: Committee reference PEL/10 Draft for comment 79/24447 DC ISBN 0 580 12788 5 Cooperating organizations The European Committee for Electrotechnical Standardization (CENELEC), under whose supervision this European Standard was p
4、repared, comprises the National Committees of the following countries: AustriaLuxemburg BelgiumNetherlands DenmarkNorway FinlandPortugal FranceSpain GermanySweden GreeceSwitzerland IrelandUnited Kingdom Italy Amendments issued since publication Amd. No.Date of issueComments Licensed Copy: sheffieldu
5、n sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6272:1982 BSI 07-1999i Contents Page Cooperating organizationsInside front cover Foreword2 Text of EN 50 0423 National appendixA8 National appendix B8 Publications referred toInside back cover Licensed Copy: sheffie
6、ldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6272:1982 ii BSI 07-1999 A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a Brit
7、ish Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, the EN title page, pages 2 to 8, an inside back cover and a back cover. This standard has been updated (see copyright date) and may h
8、ave had amendments incorporated. This will be indicated in the amendment table on the inside front cover. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 50 042 Edition 1 December 1980 UDC
9、: 621.316.54:621.3.027.2:621.315.684:003.62 Key words: Electrical switchgear and controlgear, low voltage, industrial use, terminals, marking, external contacts, external electronic components English version Low voltage switchgear and controlgear for industrial use Terminal marking Terminals for ex
10、ternal associated electronic circuit components and contacts Appareillage industriel basse tension Marquage des bornes Bornes pour les composants de circuit lectronique et pour les contacts extrieurs associs Industrielle Niederspannungs-Schaltgerte Anschlussbezeichnungen Klemmen zum Anschluss zugehr
11、iger, aussenliegender elektronischer Bauelemente und Kontakte This European Standard was accepted by CENELEC on 1980-12-11. The CENELEC members are bound to adhere to the CENELEC Internal Regulations which specify under which conditions this European Standard has to be given, without any alteration,
12、 the status of a national standard. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CENELEC General Secretariat or to any CENELEC member. This European Standard is established by CENELEC in three official versions (English, Fre
13、nch, German). A translation made by another member under its own responsibility, in its own language, and notified to CENELEC has the same status. CENELEC members are the national electrotechnical committees of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Luxemburg, N
14、etherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de Stassart 35, B-1050 Brussels Copyr
15、ight reserved to all CENELEC members Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50 042 BSI 07-1999 2 Foreword Switchgear and controlgear may be given a terminal marking in accordance with the general rules of the European Standard EN
16、 50 005. This standard gives additional requirements. Contents Foreword2 1Scope3 2Marking of terminals for external associated electronic circuit components and contacts3 3Marking of terminals of a complete device5 Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncon
17、trolled Copy, (c) BSI EN 50 042 BSI 07-19993 1 Scope This standard applies to switching devices which are able to operate only when completed with external associated electronic circuit components and contacts. The rules in this standard apply only to terminals for external associated electronic cir
18、cuit components and contacts. These are a supplement to the general rules for the marking: of control supply terminals (see EN 50 005, clause 3.1), and of terminals for internal auxiliary contact elements (see EN 50 005, clause 4.2). The use of this standard is recommended where terminal marking is
19、a requirement of the relevant standard for switching devices or is usual practice. 2 Marking of terminals for external associated electronic circuit components and contacts Terminals for external associated electronic circuit components and contacts shall be marked in the following alpha-numerical m
20、anner. 2.1 Marking of terminals for external associated impedances 2.1.1 The two terminals for an external associated impedance Z shall be marked Z1 and Z2. 2.1.2 For an impedance Z with tappings, the terminals for the tappings shall be marked in sequential order Z3, Z4, etc. 2.1.3 In case of more t
21、han one impedance, the terminals shall be marked by using the letter Z and two-figure numbers, the first figure being a sequence number. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50 042 4 BSI 07-1999 2.1.4 For particular application
22、 to a control system associated with thermistors for built-in thermal protection of rotating electrical machines, the rules for terminal marking T1, T2, . . . or 1T1, 1T2, . . . and 2T1, 2T2, . . . are given in IEC Publication 34-11 (1978), clause 6.2.1. 2.2 Marking of terminals for external associa
23、ted contacts 2.2.1 The two terminals for an external associated make or break contact or a group of contacts shall be marked Y1 and Y2. NOTE 1A bridge between two terminals is considered as a permanently closed contact and the corresponding terminals shall be marked Y1 and Y2. Licensed Copy: sheffie
24、ldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50 042 BSI 07-19995 NOTE 2For an external circuit comprising an association of impedance(s) and contact(s), the corresponding terminals shall be marked Y1 and Y2. 2.2.2 In case of more than one contact or one gro
25、up of contacts, the terminals shall be marked by using the letter Y and two-figure numbers, the first figure being a sequence number. 2.2.3 The three terminals necessary for connection of several contacts which operate simultaneously (e.g. forming a change-over contact) shall be marked Y1, Y2 and Y3
26、, Y1 being the common. 3 Marking of terminals of a complete device To illustrate the association of the general rules EN 50 005 and the rules of this standard, four examples of the terminal marking of a complete device are given as follows: Example 1. Switching device having: two control supply term
27、inals A1, A2 two terminals Z1, Z2 for an external associated variable resistor and three terminals 15, 16, 18 for an internal delayed change-over contact. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50 042 6 BSI 07-1999 Example 2. Swi
28、tching device having: two control supply terminals A1, A2 four terminals for two external associated impedances (Z11, Z12 for a variable resistor and Z21, Z22 for a capacitor) and three terminals 15, 16, 18 for an internal delayed change-over contact. Example 3. Switching device having: two control
29、supply terminals A1, A2 two terminals Y11, Y12 for an external associated group of contacts three terminals Y21, Y22, Y23 for an external associated change-over contact and three terminals 11, 12, 14 for an internal change-over contact. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27
30、 GMT+00:00 2006, Uncontrolled Copy, (c) BSI EN 50 042 BSI 07-19997 Example 4. Switching device having: two control supply terminals A1, A2 two terminals Y1, Y2 for an external bridge three terminals Z1, Z3, Z2 for an external associated resistor with a tapping and three terminals 15, 16, 18 for an i
31、nternal delayed change-over contact. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6272:1982 8 BSI 07-1999 National appendix A The United Kingdom participation in the preparation of this European Standard came under the direction of the
32、 Power Electrical Engineering Standards Committee of BSI. The committee consists of representatives from the following: Associated Offices Technical Committee Association of Short Circuit Testing Authorities* British Electrical and Allied Manufacturers Association (BEAMA) British Railways Board Brit
33、ish Steel Corporation Department of Energy Electricity Department of Industry Electrical Contractors Association* Electrical Contractors Association of Scotland Electricity Supply Industry in England and Wales* Energy Industries Council ERA Technology Ltd* Institute of Purchasing & Supply Institutio
34、n of Electrical Engineers* Ministry of Defence National Coal Board National Economic Development Office* Trades Union Congress The organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee involved with the work on this standard:
35、 Association of Control Manufacturers Tacma (BEAMA) Association of Supervisory and Executive Engineers Control and Automation Manufacturers Association (BEAMA) Electrical Installation Equipment Manufacturers Association (BEAMA) Electronic Components Industry Federation Engineering Equipment Users As
36、sociation Health and Safety Executive The Transmission & Distribution Association (BEAMA) National appendix B With reference to the foreword and clauses 1 and 3, EN 50 005 has been published as BS 5472. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy
37、, (c) BSI BS 6272:1982 BSI 07-1999 Publications referred to BS 5472 EN 50 005, Specification for low voltage switchgear and controlgear for industrial use. Terminal marking and distinctive number. General rules. IEC 34-11, Rotating electrical machines Part 11: Built-in thermal protection Chapter 1:
38、Rules for protection of rotating electrical machines. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI BS 6272:1982 EN 50 042 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body resp
39、onsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amen
40、dments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be f
41、ound on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards public
42、ations should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards B
43、SI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centr
44、e. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 700
45、1. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transm
46、itted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details
47、are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070. Licensed Copy: sheffieldun sheffieldun, na, Tue Dec 05 07:19:27 GMT+00:00 2006, Uncontrolled Copy, (c) BSI