《ISO-1163-2-1995.pdf》由会员分享,可在线阅读,更多相关《ISO-1163-2-1995.pdf(7页珍藏版)》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 I 163-2 Second edition 1995-08-15 Plastics - Unplasticized poly(vinyl chloride) (PVC-U) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties Plastiques - Poly(chlorure de viny/e) non plastifik (PVC-U) pour moulage et extr
2、usion - Partie 2: Wparation des Bprouvettes et d - use test procedures as specified in this part of IS0 1163. 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this part of IS0 1163. At the time of publication, the editi
3、ons indicated were valid. All standards are subject to revision, and parties to agreements based on this part of IS0 1163 are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. Members of IEC and IS0 maintain registers of currently valid
4、International Standards. IS0 62:1980, Plastics - Determination of water ab- sorption. IS0 75-l :I 993, Plastics - Determination of tempera- ture of deflection under load - Part 7: General test method. IS0 75-2: 1993, Plastics - Determination of tempera- ture of deflection under load - Part 2: Plasti
5、cs and ebonite. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 03:24:15 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 1163-2:1995(E) Q IS0 IS0
6、178:1993, Plastics - Determination of flexural properties. IS0 179:1993, Plastics - Determination of Charpy impact strength. IS0 291 :1977, Plastics - Standard atmospheres for conditioning and testing. IS0 293:1986, Plastics - Compression moulding test specimens of thermoplastic materials. IS0 306:1
7、994, Plastics - Thermoplastic materials - Determination of Vicat softening temperature IVSTI. IS0 527-1:1993, Plastics - Determination of tensile properties - Part 1: General principles. IS0 527-2:1993, Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusi
8、on p/as tics. IS0 527-4:-l , Plastics - Determination of tensile properties - Pat-t 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites. IS0 899-l :I 993, Plastics - Determination of creep behaviour - Part 1: Tensile creep. IS0 1163-I :A), Plastics - Unplasticized po
9、lyfvinyl chloride) (PVC-U) moulding and extrusion materials - Part 7: Designation system and basis for specifi- cations. IS0 1183:1987, Plastics - Methods for determining the density and relative density of non-cellular plastics. IS0 1210:1992, Plastics - Determination of the burning behaviour of ho
10、rizontal and vertical specimens in contact with a small-flame ignition source. IS0 2818:1994, Plastics - Preparation of test speci- mens by machining. IS0 3167:1993, Plastics - Multipurpose test speci- mens. IS0 45892:-l), Plastics - Determination of burning behaviour by oxygen index - Part 2: Ambie
11、nt- temperature test. IS0 458%3:-l), Plastics - Determination of burning behaviour by oxygen index - Part 3: Elevated- temperature test. IS0 8256:1990, Plastics - Determination of tensile- impact strength. IS0 10350:1993, Plastics - Acquisition and presen- ta tion of comparable single-point data. IE
12、C 93:1980, Methods of test for volume resistivity and surface resistivity of solid electrical insulating ma teriais. IEC 112: 1979, Method for determining the compar- ative and the proof tracking indices of solid insulating materials under moist conditions. IEC 243-l :1988, Methods of test for elect
13、ric strength of solid insulating materials - Part 7: Tests at power frequencies. IEC 250:1969, Recommended methods for the deter- mination of the permittivity and dielectric dissipation factor of electrical insulating materials at power, audio and radio frequencies including metre wavelengths. IEC 2
14、96: 1982, Specification for unused mineral insu- lating oils for transformers and switchgear. 3 Preparation of test specimens Test specimens shall be prepared by compression moulding. The method applied shall be indicated in the list of properties for every test specimen, using “Q” as the code-lette
15、r for compression moulding. It is essential that all specimens prepared by a par- ticular method are prepared using the same process- ing conditions given in tables 1 and 2. 3.1 Treatment of the material before moulding Before compression moulding, the material shall be preplasticized in a two-roll
16、mill, using the conditions specified in table 1. 3.2 Compression moulding Place the required number of milled sheets, prefer- ably crosslayered, in the preheated mould and prepare compression-moulded sheets in accordance with IS0 293, using the conditions specified in table2. 1) To be published. 2)
17、To be published. (Revision of IS0 1163-1:1985) 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 03:24:15 MDTNo reproduction or networking permitted without license from IHS -,-,
18、- IS0 1163-2:1995(E) Table 1 - Conditions for preplasticizing test specimens Material All grades Mill-roll surface Milling time Roll surface Friction Roll nip Roll temperature speed ratio width diameter Roll length “C min m/min mm mm mm VST/B + 90 521 e.g. 10 1:1,2 e.g. 1 e.g. 150 e.g. 300 (Ik 10) T
19、able 2 - Conditions for compression moulding of test specimens “C -C/min “C MPa min MPa min All grades VST/B + 100 15 * 3 8Ox 380x1 a Frequency 1 kHz (compensate for Dissipation factor electrode edge effect) - 1 Volume resistivity IL. m IEC 93 80 380x1 cl Voltage 500 V Surface resistivity s-2 Electr
20、ic strength kV/mm IEC 243-l 380 280x1 Q Use 25 mm/75 mm coaxialcylinder electrode configuration. Immerse in IEC 296 transformer oil. Use short time (rapid rise) test Comparative tracking index - IEC 112 315x 2 15x4 Q Use solution A Other properties Water absorption % IS0 62 50 x 50 x 4 Q 24 h immers
21、ion in water at 23 “C Density kglm3 IS0 1183 10x10x4 0 I) 0 = Compression moulding 2) Designatory property Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 03:24:15 MDTNo reproduc
22、tion or networking permitted without license from IHS -,-,- IS0 1163-2:1995(E) ICS 83.080.20 Descriptors: plastics, homopolymers, copolymers, polyvinyl chloride, unplasticized polyvinyl chloride, tests, determination, properties. Price based on 4 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/27/2007 03:24:15 MDTNo reproduction or networking permitted without license from IHS -,-,-