《ISO-1173-2001.pdf》由会员分享，可在线阅读，更多相关《ISO-1173-2001.pdf（14页珍藏版）》请在三一文库上搜索。
1、Reference number ISO 1173:2001(E) ISO 2001 INTERNATIONAL STANDARD ISO 1173 Third edition 2001-04-01 Assembly tools for screws and nuts Drive ends for hand- and machine-operated screwdriver bits and connecting parts Dimensions, torque testing Outils de manuvre pour vis et crous Entranements des embou
2、ts tournevis main et machine et lments de connexion Dimensions, couple dessai Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted
3、without license from IHS -,-,- ISO 1173:2001(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer pe
4、rforming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this
5、 PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Centra
6、l Secretariat at the address given below. ISO 2001 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at
7、the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 ? CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2001 All rights reserved Copyright International Organizati
8、on for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1173:2001(E) ISO 2001 All rights reservediii Foreword ISO (the International
9、Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been esta
10、blished has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardiza
11、tion. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75
12、% of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 1173 was prepared by
13、Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This third edition cancels and replaces the second edition (ISO 1173:1988), which has been technically revised. Annex A of this International Standard is for information only. Copy
14、right International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardiz
15、ation Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARDISO 1173:2001(E) ISO 2001 All rights reserved1 Assembly tools for screws and
16、 nuts Drive ends for hand- and machine-operated screwdriver bits and connecting parts Dimensions, torque testing 1Scope This International Standard specifies the dimensions and torque testing of drive ends for hand- and machine-operated screwdriver bits as well as to driving spindles of screw drivin
17、g machines. It ensures the interchangeability of tool bits and tool holders. This International Standard defines only the distinctive features of individual drive ends. Details of design, e.g. of fixing devices, are left to the user of this International Standard. 2Dimensions See Figures 1 to 8 and
18、Tables 1 to 8. Details not given shall be chosen appropriately. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without licens
19、e from IHS -,-,- ISO 1173:2001(E) 2 ISO 2001 All rights reserved a Retaining system of the manufacturers choice Figure 1 Male hexagon form AFigure 2 Female hexagon form B Table 1 Male hexagon form A Dimensions in millimetres s1d1d3e1l1l3l5r Form Nominal dimension max.min.h9h12max.min.min. 0 0,2? 0,4
20、 0 ? min. 332,963,633,393,3419,511,97,41,00 A 5,55,505,456,75,76,216,16241610,91,25 Table 2 Female hexagon form B Dimensions in millimetres s2d2e2l2l4l6 Form Nominal dimension max.min.D10min.? 0,1 0,2 0 ?0 0,4? 33,063,023,63,4116,511,97,2 B 5,55,585,536,76,25211610,7 Copyright International Organiza
21、tion for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1173:2001(E) ISO 2001 All rights reserved3 Nominal dimension 4 Nominal dime
22、nsions 6,3, 8 and 12,5 a 40 u ? u 60 b 80 u ? u 120 a Retaining system of the manufacturers choice. Figure 3 Male hexagon form CFigure 4 Female hexagon form D Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/997254500
23、1 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1173:2001(E) 4 ISO 2001 All rights reserved Table 3 Male hexagon form C Dimensions in millimetres s1d3e1l1l3r Form Nominal dimension max.min.h12max.min.min. 0 0,2? min. 43,963,914,484,
24、4294 6,36,356,296,77,187,11118,2 87,937,878,28,968,9013,510,2 C 12,512,7012,6313,514,3514,2715,912,7 0,3 Table 4 Female hexagon form D Dimensions in millimetres s2e2l2l4 Form Nominal dimension max.min.min.? 0,1 0,2 0 ? 44,043,994,5184 6,36,456,397,22108,2 88,037,97912,510,2 D 12,512,8012,7514,414,91
25、2,7 a Retaining system of the manufacturers choice. Figure 5 Male hexagon form EFigure 6 Female hexagon form F Table 5 Male hexagon form E Dimensions in millimetres s1d3e1l1l3l7r Form Nominal dimension max.min.h12max.min.min. 0 0,1? ?min. 6,36,356,294,77,187,11259,512,4 (8)a 7,937,876,38,968,90275,4
26、1,22,4 E 11,211,1111,048,712,5612,4831,56,71,22,8 a Non-preferred dimension. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted w
27、ithout license from IHS -,-,- ISO 1173:2001(E) ISO 2001 All rights reserved5 Table 6 Female hexagon form F Dimensions in millimetres s2e2l2l4 Form Nominal dimension max.min.min.max. 0,1 0 ? 6,36,456,397,22249,5 (8)a8,037,97925,55,4 F 11,211,2311,1612,61306,7 a Non-preferred dimension. a Arrangement
28、with test role for the determination of the groove depth. a Retaining system of the manufacturers choice. Figure 7 Male flat end form GFigure 8 Female flat end form H Table 7 Male flat end form G Dimensions in millimetres d1d3e1l1l3l5r Form Nominal dimension f8h12max.min.min.? 0,2? 0,2min. G775,83,8
29、63,742620141,5 Table 8 Female flat end form H Dimensions in millimetres d2e2l2l4l6 Form Nominal dimension H10 0,1 0 ? max.min.? 0,2 H774,12620,514 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Re
30、sale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1173:2001(E) 6 ISO 2001 All rights reserved 3Design Form D ?Magnetic types for hand-operated screwdriver bits may be manufactured without a bore for a ball or without a groove for a retaining (sna
31、p) ring. Form G ?Male flat ends may also have a V-shaped ring groove instead of a circular arc shape ring groove (of the manufacturers choice), which shall comply with the pictorial representation. 4Designation A drive end conforming to this International Standard shall be designated by a)“Male hexa
32、gon“ or “Female hexagon“ in the case of a design with a male or a female hexagon drive respectively; b)“Male flat end“ or “Female flat end“ in the case of a design with a male or female flat end respectively; c)reference to this International Standard, i.e. ISO 1173; d)capital letter for the respect
33、ive form (A, B, C, D, E, F, G or H); e)nominal dimension. EXAMPLE 1A male hexagon Form A of nominal dimension 3 is designated as follows: Male hexagon ISO 1173 - A 3 EXAMPLE 2A female hexagon Form B of nominal dimension 3 is designated as follows: Female hexagon ISO 1173 - B 3 EXAMPLE 3A male hexago
34、n Form C of nominal dimension 8 is designated as follows: Male hexagon ISO 1173 - C 8 EXAMPLE 4A female hexagon Form D of nominal dimension 8 is designated as follows: Female hexagon ISO 1173 - D 8 EXAMPLE 5A male hexagon Form E of nominal dimension 11,2 is designated as follows: Male hexagon ISO 11
35、73 - E 11,2 EXAMPLE 6A female hexagon Form F of nominal dimension 11,2 is designated as follows: Female hexagon ISO 1173 - F 11,2 EXAMPLE 7A male flat end Form G of nominal dimension 7 is designated as follows: Male flat end ISO 1173 - G 7 EXAMPLE 8A female hexagon Form H of nominal dimension 7 is d
36、esignated as follows: Female flat end ISO 1173 - H 7 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS
37、-,-,- ISO 1173:2001(E) ISO 2001 All rights reserved7 5Torque testing 5.1Test piece For torque testing, test devices shall be used which correspond in their dimensions to the respective “counterbodies“ of the connecting parts to be tested. The same dimensional specifications apply to the test pieces
38、as to the connection parts, however, they do not have to be equipped with a retaining system. The torque test device and the test pieces shall have a hardness of at least HRC 62. 5.2Test values The test torque values for torque testing are given in Table 9. Following the application of the test torq
39、ue the connecting parts shall show no permanent deformation or any other damage, such as e.g. cracks or fractures, which might affect the usability of the tool. Table 9 Test torque values Nominal dimension Test torquea min. Form mmN?m 37,6 A, B 5,547 418 6,371 8144 C, D 12,5478 6,371 8144E, F 11,239
40、6 G, H725 a The values for the test torque apply only to connecting parts made of alloyed steel for hardening and tempering or tool steel, heat treated over its whole length, having a hardness of at least HRC 53. When testing with the test torque it shall be ensured that the connecting parts to be t
41、ested are engaged under load over their whole lengths l1and l2. The test torque shall be applied smoothly and steadily. Following the application of the minimum test torque, any resulting damage or deformation shall not affect the usability of the tool. Copyright International Organization for Stand
42、ardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1173:2001(E) 8 ISO 2001 All rights reserved Annex A (informative) Explanatory notes In th
43、e case of screwdriver bits and driving spindles of electric and pneumatic screwdrivers driving is performed by hexagon connection or a flat end connection. The interchangeability of tool bits and tool holders is ensured by the standardization of the drive ends. To emphasize the relation between the
44、matching dimensions of male and female hexagons or male and female flat ends respectively, this International Standard has been editorially designed such that dimensional letters for male parts have only uneven subscripts (1, 3, 5 .) and for female parts even subscripts (2, 4, 6 .). In order to coor
45、dinate the corner dimensions of the hexagon ends they were calculated according to following formulae: e1 max= 1,13 s1 max e1 min= 1,13 s1 min e2 min= 1,13 s2 min Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/99725
46、45001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo
47、 reproduction or networking permitted without license from IHS -,-,- ISO 1173:2001(E) ICS 25.140.30 Price based on 8 pages ISO 2001 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:47:38 MDTNo reproduction or networking permitted without license from IHS -,-,-