《ISO-15785-2002.pdf》由会员分享，可在线阅读，更多相关《ISO-15785-2002.pdf（14页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 15785:2002(E) ISO 2002 INTERNATIONAL STANDARD ISO 15785 First edition 2002-07-01 Technical drawings Symbolic presentation and indication of adhesive, fold and pressed joints Dessins techniques Reprsentation symbolique et indication des assemblages colls, replis et clinchs Copyr
2、ight International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) PDF disclaimer This PDF file may c
3、ontain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the respons
4、ibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
5、parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2002 All rights reserved. Unless oth
6、erwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyrig
7、ht office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.ch Web www.iso.ch Printed in Switzerland ii ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technica
8、l Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) ISO 2002 All rights reserved iii Contents Page Foreword.iv 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Graphical symbols.2 5 Indi
9、cation of joints in drawings3 6 Basic conventions for symbolic presentation and indication of joints.4 7 Designation examples.5 Annex A (normative) Presentation and dimensions of graphical symbols7 Copyright International Organization for Standardization Provided by IHS under license with ISO Licens
10、ee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) iv ISO 2002 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of nati
11、onal standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internat
12、ional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the ru
13、les given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at
14、 least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15785 was prepared by Technical Co
15、mmittee ISO/TC 10, Technical product documentation, Subcommittee SC 6, Mechanical engineering documentation. Annex A forms a normative part of this International Standard. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standard
16、s 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 15785:2002(E) ISO 2002 All rights reserved 1 Technical drawings Symbolic presentation and indication of adhesive, fold and pressed joints 1 Scope Th
17、is International Standard establishes rules for the symbolic presentation and indication of adhesive, fold and pressed joints in technical drawings. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions of this Intern
18、ational Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents
19、 indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 128-20, Technical drawings General principles of presentation Part 20: Basic conventions for lines ISO
20、 128-22, Technical drawings General principles of presentation Part 22: Basic conventions and applications for leader lines and reference lines ISO 128-24:1999, Technical drawings General principles of presentation Part 24: Lines on mechanical engineering drawings ISO 129-1:1), Technical drawings In
21、dication of dimensions and tolerances Part 1: General principles ISO 2553, Welded, brazed and soldered joints Symbolic representation on drawings ISO 3098-0:1997, Technical product documentation Lettering Part 0: General requirements ISO 17659:2002, Welding Multilingual terms for welded joints with
22、illustrations 3 Terms and definitions For the purposes of this International Standard, the terms and definitions given in ISO 128-22 and the following apply. 3.1 joint junction of workpieces or edges of workpieces that are to be joined or have been joined ISO 17659:2002, definition 3.1 1) To be publ
23、ished. (Revision of ISO 129:1985) Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:200
24、2(E) 2 ISO 2002 All rights reserved 3.1.1 adhesive joint joint of two or more parts of similar or different materials made using adhesives 3.1.2 fold joint joint of two edges of surfaces of similar or different materials made by catching and coupling 3.1.3 pressed joint joint of two or more parts of
25、 sheet materials made by simultaneous deformation from two sides by means of (cylindrical, rectangular etc.) tools 4 Graphical symbols 4.1 General The joints specified in this International Standard are identified by the symbols shown in Figures 1 to 4. The manner of presentation and the dimensions
26、of these symbols are given in Annex A. NOTE The symbols shown in Figures 1 to 3 are identical to those given in ISO 2553 for joints of identical configuration. 4.2 Adhesive joints Adhesive joints shall be identified by the symbols shown in Figures 1 and 2. A surface joint shall be identified by the
27、symbol shown in Figure 1. Figure 1 Symbol for surface joint An inclined joint shall be identified by the symbol shown in Figure 2. Figure 2 Symbol for inclined joint 4.3 Fold joint A fold joint shall be identified by the symbol shown in Figure 3. Copyright International Organization for Standardizat
28、ion Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) ISO 2002 All rights reserved 3 Figure 3 Symbol for fold joint 4.4 Pressed joint A
29、pressed joint shall be identified by the symbol shown in Figure 4. Figure 4 Symbol for pressed joint 5 Indication of joints in drawings The symbols shall be drawn using a continuous wide line in accordance with ISO 128-24 (see Figure 5 for an example), supplemented by the applicable information in a
30、ccordance with ISO 2553. The distance between the graphical symbol and the reference line shall be at least 2d (for d, see Annex A). The leader line and reference line shall be drawn using a continuous narrow line in accordance with ISO 128-22. The leader line shall end in an arrow (see Figure 5) an
31、d the reference line may begin with a fork (see Figure 6), where additional requirements may be indicated (see Figure 7). Figure 5 Symbol with reference line and leader line Figure 6 Reference line with fork Figure 7 Additional information with reference line Copyright International Organization for
32、 Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) 4 ISO 2002 All rights reserved In addition to the symbol, the followi
33、ng may be indicated with the reference line, as necessary: a) the dimensions of the cross-section of the joint (width and height, punch diameter, depth of punching etc.), placed at left of symbol; b) other characteristics, for example, designations of the material, placed at right of symbol; c) addi
34、tional requirements for the joint, placed in the fork (see Figure 7). The dimensions that locate the joint shall be indicated in accordance with ISO 129-1. 6 Basic conventions for symbolic presentation and indication of joints 6.1 Adhesive joints Adhesive joints shall be shown without an indication
35、of the adhesive, as shown in Figures 8 and 9. Figure 8 Indication of surface joint Figure 9 Indication of inclined joint To indicate a continuous adhesive joint formed around the periphery of a part, a circle shall be added at the intersection between the leader and reference lines in accordance wit
36、h ISO 128-22 (see Figure 10). Figure 10 Indication of joint around periphery Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted w
37、ithout license from IHS -,-,- ISO 15785:2002(E) ISO 2002 All rights reserved 5 An adhesive joint limited to an area shall be indicated using a type 05.1.8 long-dashed double-dotted narrow line in accordance with ISO 128-24:1999 (see Figure 11). Figure 11 Indication of limited area 6.2 Fold joints Fo
38、ld joints shall be presented in accordance with the general principles given in ISO 128-20, ISO 128-22 and ISO 128-24. 6.3 Pressed joints If a joint is made by mechanical pressing in more than one place, the dimensions specifying the locations of the pressings shall be shown on the presentation of t
39、he parts being jointed (see Figure 12). Figure 12 Indication of pressed joint 7 Designation examples Examples of designations are given in Table 1. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for R
40、esale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) 6 ISO 2002 All rights reserved Table 1 Designation examples Type of connection Presentation Designation Adhesive Fold Pressed Copyright International Organization for Standardizatio
41、n Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15785:2002(E) ISO 2002 All rights reserved 7 Annex A (normative) Presentation and dimensions of gr
42、aphical symbols The presentation and dimensions of the graphical symbols shall be as shown in Figures A.1 to A.4. The line width, d, for both graphical symbols and upright letters shall be d = 0,1 h where h is the lettering height according to ISO 3098-0:1997. Figure A.1 Adhesive joint Surface joint
43、 Figure A.2 Adhesive joint Inclined joint Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 1
44、5785:2002(E) 8 ISO 2002 All rights reserved Figure A.3 Fold joint Figure A.4 Pressed joint Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networki
45、ng permitted without license from IHS -,-,- Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO
46、 15785:2002(E) ICS 01.100.20 Price based on 8 pages ISO 2002 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=NASA Technical Standards 1/9972545001 Not for Resale, 04/22/2007 08:23:12 MDTNo reproduction or networking permitted without license from IHS -,-,-