《ISO-15493-2003.pdf》由会员分享，可在线阅读，更多相关《ISO-15493-2003.pdf（70页珍藏版）》请在三一文库上搜索。
1、 Reference number ISO 15493:2003(E) ISO 2003 INTERNATIONAL STANDARD ISO 15493 First edition 2003-04-15 Plastics piping systems for industrial applications Acrylonitrile-butadiene- styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) Specifications fo
2、r components and the system Metric series Systmes de canalisations en matires plastiques pour les applications industrielles Acrylonitrile-butadine-styrne (ABS), poly(chlorure de vinyle) non plastifi (PVC-U) et poly(chlorure de vinyle) chlor (PVC-C) Spcifications pour les composants et le systme Sri
3、e mtrique Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15493:2003(E) PDF disclaime
4、r This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accep
5、t therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the fi
6、le; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2003 All rights
7、 reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the r
8、equester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2003 All rights reserved Copyright International Organization for Standardization Provided by IHS under license with I
9、SO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15493:2003(E) ISO 2003 All rights reserved iii Contents Page Foreword iv Introduction. v 1 Scope 1 2 Normative references 2 3 Term
10、s and definitions. 4 4 Symbols and abbreviated terms 7 5 Material. 8 6 General characteristics. 10 7 Geometrical characteristics. 10 8 Mechanical characteristics. 11 9 Physical characteristics . 11 10 Chemical characteristics 12 11 Adhesives 12 12 Performance requirements. 12 13 Classification of co
11、mponents 13 14 Design of a thermoplastics piping system for industrial applications 13 15 Installation of piping systems 13 16 Declaration of compliance 14 17 Marking. 14 Annex A (normative) Specific characteristics and requirements for industrial piping systems made from acrylonitrile-butadiene-sty
12、rene (ABS) 16 Annex B (normative) Specific characteristics and requirements for industrial piping systems made from unplasticized poly(vinyl chloride) (PVC-U) 30 Annex C (normative) Specific characteristics and requirements for industrial piping systems made from chlorinated poly(vinyl chloride) (PV
13、C-C). 44 Bibliography 62 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15493:2003(E
14、) iv ISO 2003 All rights reserved Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body int
15、erested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnic
16、al Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the
17、technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of p
18、atent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 15493 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 3, Plastics pipes and fittings for industrial applications. This d
19、ocument has been prepared under a mandate given by the European Commission and the European Free Trade Association and supports essential requirements of EU Directives. At the date of publication of this International Standard, the following standards had been published for piping systems, used for
20、industrial applications, made from other types of plastic: ISO 10931 (all parts), Plastics piping systems for industrial applications Poly(vinylidene fluoride) (PVDF) ISO 15494, Plastics piping systems for industrial applications Polybutene (PB), polyethylene (PE) and polypropylene (PP) Specificatio
21、ns for components and the system Metric series. Annexes A, B and C form a normative part of this International Standard. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:
22、27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15493:2003(E) ISO 2003 All rights reserved v Introduction This International Standard specifies the characteristics and requirements for a piping system and its components made from acrylonitrile-butadiene-styrene (A
23、BS), unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C), as applicable, intended to be used for industrial applications above ground by authorities, design engineers, certification bodies, inspection bodies, test laboratories, manufacturers and users. Copyright In
24、ternational Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- Copyright International Organization for Standardizat
25、ion Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- INTERNATIONAL STANDARD ISO 15493:2003(E) ISO 2003 All rights reserved 1 Plastics piping system
26、s for industrial applications Acrylonitrile- butadiene-styrene (ABS), unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly(vinyl chloride) (PVC-C) Specifications for components and the system Metric series 1 Scope This International Standard specifies the characteristics and requirements
27、for components such as pipes, fittings and valves made from one of the following materials: acrylonitrile-butadiene-styrene (ABS); unplasticized poly(vinyl chloride) (PVC-U); chlorinated poly(vinyl chloride) (PVC-C); intended to be used for thermoplastics piping systems in above-ground industrial ap
28、plications. This International Standard is applicable to ABS, PVC-U or PVC-C pipes, fittings, valves and ancillary equipment, to their joints and to joints with components made of other plastics and non-plastics materials, depending on their suitability, intended to be used for the conveyance of liq
29、uid and gaseous fluids as well as of solid matter in fluids for industrial applications such as: chemical plants; industrial sewerage engineering; power engineering (cooling and general-purpose water supply); electroplating and pickling plants; the semiconductor industry; agricultural production pla
30、nts; water treatment. NOTE 1 Where relevant, national regulations for specific applications (e.g. water treatment) apply. Other application areas are permitted if the requirements of this International Standard and/or applicable national requirements are fulfilled. Relevant regulations in respect of
31、 fire behaviour and explosion risk are applicable if applications are envisaged for inflammable media. The components have to withstand the mechanical, thermal and chemical demands to be expected and have to be resistant to the fluids to be conveyed. Copyright International Organization for Standard
32、ization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15493:2003(E) 2 ISO 2003 All rights reserved Characteristics and requirements which ar
33、e applicable to all three materials (ABS, PVC-U and PVC-C) are covered by the relevant clauses of this International Standard. Those characteristics and requirements which are dependent on the material are given for each material in the relevant annex (see Table 1). Table 1 Material-specific annexes
34、 Material Annex Acrylonitrile-butadiene-styrene (ABS) A Unplasticized poly(vinyl chloride) (PVC-U) B Chlorinated poly(vinyl chloride) (PVC-C) C NOTE 2 Components conforming to any of the product standards listed in the bibliography or to national standards, as applicable, may be used with components
35、 conforming to this International Standard provided they conform to the requirements for joint dimensions and to the other relevant requirements of this standard. 2 Normative references The following normative documents contain provisions which, through reference in this text, constitute provisions
36、of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the most recent editions of the norma
37、tive documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 7-1, Pipe threads where pressure-tight joints are made on the threads Part 1: Dimensions
38、, tolerances and designation ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation ISO 265-1, Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unp
39、lasticized poly(vinyl chloride) (PVC-U) ISO 306, Plastics Thermoplastic materials Determination of Vicat softening temperature (VST) ISO 472, Plastics Vocabulary ISO 580:1), Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fittings Oven test Test method and basic specifications ISO 727-1
40、, Fittings made from unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly(vinyl chloride) (PVC-C) or acrylonitrile/butadiene/styrene (ABS) with plain sockets for pipes under pressure Part 1: Metric series ISO 1043-1, Plastics Symbols and abbreviated terms Part 1: Basic polymers and their spe
41、cial characteristics ISO 1158, Plastics Vinyl chloride homopolymers and copolymers Determination of chlorine content ISO 1167:1996, Thermoplastics pipes for the conveyance of fluids Resistance to internal pressure Test method 1) To be published. (Revision of ISO 580:1990) Copyright International Org
42、anization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/04/2007 23:27:19 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO 15493:2003(E) ISO 2003 All rights reserved 3 ISO 1183-2, Plastic
43、s Methods for determining the density of non-cellular plastics Part 2: Density gradient column method ISO 2505-1:1994, Thermoplastics pipes Longitudinal reversion Part 1: Determination methods ISO 2505-2:1994, Thermoplastics pipes Longitudinal reversion Part 2: Determination parameters ISO 2507-1, T
44、hermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 2507-2, Thermoplastics pipes and fittings Vicat softening temperature Part 2: Test conditions for unplasticized poly(vinyl chloride) (PVC-U) or chlorinated poly(vinyl chloride) (PVC-C) pipes and fittings and
45、 for high impact resistance poly(vinyl chloride) (PVC-HI) pipes ISO 3126, Plastics piping systems Plastics piping components Measurement and determination of dimensions ISO 3127, Thermoplastics pipes Determination of resistance to external blows Round-the-clock method ISO 3514, Chlorinated polyvinyl
46、 chloride (CPVC) pipes and fittings Specification and determination of density ISO 4065, Thermoplastics pipes Universal wall thickness table ISO 9080, Plastics piping and ducting systems Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation ISO
47、 9311-1, Adhesives for thermoplastics piping systems Part 1: Determination of film properties ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method ISO 9853, Injection-moulded unplasticized poly(vinyl chloride) (PVC-U) fitti
48、ngs for pressure pipe systems Crushing test ISO/TR 10358, Plastics pipes and fittings Combined chemical-resistance classification table ISO 11922-1:1997, Thermoplastics pipes for the conveyance of fluids Dimensions and tolerances Part 1: Metric series ISO 12092, Fittings, valves and other piping system components made of unplasticized poly(vinyl chloride) (PVC-U),