《ISO-TR-11610-2004-EF.pdf》由会员分享，可在线阅读，更多相关《ISO-TR-11610-2004-EF.pdf（104页珍藏版）》请在三一文库上搜索。
1、 Reference number Numro de rfrence ISO/TR 11610:2004(E/F) ISO 2004 TECHNICAL REPORT RAPPORT TECHNIQUE ISO/TR 11610 First edition Premire dition 2004-04-15 Protective clothing Vocabulary Vtements de protection Vocabulaire Copyright International Organization for Standardization Provided by IHS under
2、license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 23:51:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 11610:2004(E/F) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing
3、policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Cent
4、ral Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been tak
5、en to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. PDF Exonration de responsabilit Le prsent fichier PDF peut contenir des polices de caractres intgres. C
6、onformment aux conditions de licence dAdobe, ce fichier peut tre imprim ou visualis, mais ne doit pas tre modifi moins que lordinateur employ cet effet ne bnficie dune licence autorisant lutilisation de ces polices et que celles-ci y soient installes. Lors du tlchargement de ce fichier, les parties
7、concernes acceptent de fait la responsabilit de ne pas enfreindre les conditions de licence dAdobe. Le Secrtariat central de lISO dcline toute responsabilit en la matire. Adobe est une marque dpose dAdobe Systems Incorporated. Les dtails relatifs aux produits logiciels utiliss pour la cration du prs
8、ent fichier PDF sont disponibles dans la rubrique General Info du fichier; les paramtres de cration PDF ont t optimiss pour limpression. Toutes les mesures ont t prises pour garantir lexploitation de ce fichier par les comits membres de lISO. Dans le cas peu probable o surviendrait un problme dutili
9、sation, veuillez en informer le Secrtariat central ladresse donne ci-dessous. ISO 2004 The reproduction of the terms and definitions contained in this International Standard is permitted in teaching manuals, instruction booklets, technical publications and journals for strictly educational or implem
10、entation purposes. The conditions for such reproduction are: that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar publications offered for sale; and that this International Standard is referenced as the source document. With
11、 the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member body in the country of the
12、requester. La reproduction des termes et des dfinitions contenus dans la prsente Norme internationale est autorise dans les manuels denseignement, les modes demploi, les publications et revues techniques destins exclusivement lenseignement ou la mise en application. Les conditions dune telle reprodu
13、ction sont les suivantes: aucune modification nest apporte aux termes et dfinitions; la reproduction nest pas autorise dans des dictionnaires ou publications similaires destins la vente; la prsente Norme internationale est cite comme document source. la seule exception mentionne ci-dessus, aucune pa
14、rtie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lISO ladresse ci-aprs ou du comit membre de lISO dans le pays du demandeur. ISO copyright office Cas
15、e postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland/Publi en Suisse ii ISO 2004 All rights reserved/Tous droits rservs Copyright International Organization for Standardization Provided by IHS under license with
16、ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 23:51:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 11610:2004(E/F) ISO 2004 All rights reserved/Tous droits rservs iii Foreword ISO (the International Organization for Standardi
17、zation) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to b
18、e represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standa
19、rds are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Inter
20、national Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO/TR 1161
21、0 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 94, Personal safety Protective clothing and equipment, Subcommittee SC 13, Protective clothing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Ag
22、reement). Throughout the text of this document, read “.this CEN Report.” to mean “.this Technical Report.”. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 23:51:18 MDTNo r
23、eproduction or networking permitted without license from IHS -,-,- ISO/TR 11610:2004(E/F) iv ISO 2004 All rights reserved/Tous droits rservs Avant-propos LISO (Organisation internationale de normalisation) est une fdration mondiale dorganismes nationaux de normalisation (comits membres de lISO). Lla
24、boration des Normes internationales est en gnral confie aux comits techniques de lISO. Chaque comit membre intress par une tude a le droit de faire partie du comit technique cr cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en liaison avec lISO participent ga
25、lement aux travaux. LISO collabore troitement avec la Commission lectrotechnique internationale (CEI) en ce qui concerne la normalisation lectrotechnique. Les Normes internationales sont rdiges conformment aux rgles donnes dans les Directives ISO/CEI, Partie 2. La tche principale des comits techniqu
26、es est dlaborer les Normes internationales. Les projets de Normes internationales adopts par les comits techniques sont soumis aux comits membres pour vote. Leur publication comme Normes internationales requiert lapprobation de 75 % au moins des comits membres votants. Lattention est appele sur le f
27、ait que certains des lments du prsent document peuvent faire lobjet de droits de proprit intellectuelle ou de droits analogues. LISO ne saurait tre tenue pour responsable de ne pas avoir identifi de tels droits de proprit et averti de leur existence. LISO/TR 11610 a t labor par le Comit europen de n
28、ormalisation (CEN) en collaboration avec le comit technique ISO/TC 94, Scurit individuelle Vtements et quipements de protection, sous-comit SC 13, Vtements de protection, conformment lAccord de coopration technique entre lISO et le CEN (Accord de Vienne). Tout au long du texte du prsent document, li
29、re le prsent Rapport CEN avec le sens de le prsent Rapport technique . Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 23:51:18 MDTNo reproduction or networking permitted w
30、ithout license from IHS -,-,- ISO/TR 11610:2004(E/F) ISO 2004 All rights reserved/Tous droits rservs v Contents 1 Scope 1 1 Domaine dapplication. 1 1 Anwendungsbereich 1 2 General. 2 2 Gnralits. 2 2 Allgemeines. 2 3 Terms and definitions. 3 3 Termes et dfinitions 3 3 Begriffe. 3 Copyright Internatio
31、nal Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 23:51:18 MDTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 11610:2004(E/F) vi ISO 2004 All rights reserved/Tous d
32、roits rservs Foreword This document (CEN ISO/TR 11610:2004) has been prepared by Technical Committee CEN/TC 162, “Protective clothing including hand and arm protection and lifejackets“, the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 94 “Personal safety - Pr
33、otective clothing and equipment“. Avant-propos Le prsent document CEN ISO/TR 11610:2004 a t labor par le Comit Technique CEN/TC 162 “Vtements de protection, y compris la protection de la main et du bras et y compris les gilets de sauvetage”, dont le secrtariat est tenu par DIN, en collaboration avec
34、 le Comit Technique ISO/TC 94 “Scurit individuelle - Vtements et quipements de protection”. Vorwort Dieses Dokument (CEN ISO/TR 11610:2004) wurde vom Technischen Komitee CEN/TC 162 Schutzkleidung einschlielich Hand- und Armschutz und Rettungswesten”, dessen Sekretariat vom DIN gehalten wird, in Zusa
35、mmenarbeit mit dem Technischen Komitee ISO/TC 94 Personal safety - Protective clothing and equipment” erarbeitet. Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 04/03/2007 23:51:18 M
36、DTNo reproduction or networking permitted without license from IHS -,-,- ISO/TR 11610:2004(E/F) ISO 2004 All rights reserved/Tous droits rservs vii Introduction The definitions compiled in this document are based on the standards and draft standards prepared by CEN/TC 162. For this reason, the terms
37、 and definitions laid down in this technical report do not only cover protective clothing and related terms but also terms from the areas of protective gloves and lifejackets which come within the scope of CEN/TC 162. Since the document was developed under clause 5.2 of the Vienna Agreement, it also
38、 takes account of terms and definitions of the relevant ISO-TC for protective clothing, ISO/TC 94/SC 13. In addition, terms from the ISO/IEC Guide as well as terms applied in American standardisation are included in so far as CEN/TC 162 use them in its standardising activities. The document is based
39、 on the compilation of terms and definitions existing in the area of standardisation of CEN/TC 162 and ISO/TC 94/SC 13 as published before February 1999. The objective was not to establish a complete, consistent terminology as described in ISO 704, ISO 860 and ISO 10241. In order to set up this docu
40、ment, a compilation of the established definitions was realised on the basis of the existing standards and draft standards in CEN/TC 162 and relevant documents in ISO/TC 94/SC 13. The subject matter of the definitions taken from standards and draft standards have not been modified, but since there w
41、ere some inconsistencies in the wording of definitions and since some terms were given several definitions, it has proved necessary to simplify or alter some wordings and to harmonise the definitions concerned. This was done in co-ordination with the convenors of the Working Groups in CEN/TC 162 and
42、 those responsible in ISO/TC 94/SC 13, so as to eliminate contradictions wherever possible. Introduction Les dfinitions runies dans ce document sont bases sur des normes et des projets de normes prpars par le CEN/TC 162. Pour cette raison, les termes et dfinitions arrtes dans ce rapport technique co
43、uvrent non seulement des vtements de protection et des termes associs mais concernent galement les domaines des gants de protection et des gilets de sauvetage qui entrent dans de domaine de comptences du CEN/TC 162. tant donn que le document a t tabli conformment au paragraphe 5.2 de lAccord de Vien
44、ne, il tient galement compte des termes et dfinitions de lISO-TC appropris aux vtements de protection, ISO/TC 94/SC 13. De plus, les termes du Guide ISO/IEC ainsi que les termes utiliss dans la normalisation amricaine sont inclus dans la mesure o le CEN/TC 162 les emploie dans ses activits de normal
45、isation. Ce document est bas sur la compilation des termes et dfinitions existant dans le domaine de normalisation du CEN/TC 162 et lISO/TC 94/SC 13 publis avant Fvrier 1999. Lobjectif ntait pas dtablir une terminologie complte, cohrente comme dcrit dans lISO 704, lISO 860 et lISO 10241. Pour ralise
46、r ce document, une compilation des dfinitions tablies a t ralise sur la base des normes et projets de normes existant au CEN/TC 162 ainsi que des documents appropris de lISO/TC 94/SC 13. Einleitung Die Grundlage fr die Erarbeitung der in diesem Norm-Entwurf zusammengestellten Definitionen bildeten d
47、ie in den Normen des CEN/TC 162 bestehenden Definitionen. Aus diesem Grund beziehen sich die in diesem technischen Bericht festgelegten Begriffe und Definitionen nicht ausschlielich auf Schutzkleidung und hiermit in Zusammenhang stehende Begriffe, sondern umfassen auch Begriffe aus den Bereichen Sch
48、utzhandschuhe und Rettungswesten, die jeweils im Geltungsbereich des CEN/TC 162 eingeschlossen sind. Da die Erarbeitung des Dokuments unter Abschnitt 5.2 des Wiener Abkommens erfolgte, wurden auerdem Begriffe und Definitionen aus dem Bereich des entsprechenden ISO-TCs fr Schutzkleidung ISO/TC 94/SC 13 be