《ISO-8022-1990.pdf》由会员分享，可在线阅读，更多相关《ISO-8022-1990.pdf（11页珍藏版）》请在三一文库上搜索。
1、INTERNATIONAL STANDARD IS0 8022 Second edition 1990-07-15 ANSI Ilafrna“ Dcx SexY Surface active agents - Determination of wetting power by immersion Agents de surface - D maintenance of complete submersion in the solution, by means of the specially designed gripper, of the cotton disc, which tends t
2、o float to the surface due to air trapped in the cloth. After displacement of air and penetration of the solution into the cloth, the cotton disc starts to sink. Determination of the wetting time by measuring the interval between the moment of immersion of the cotton disc and the moment when it begi
3、ns to sink. Determination of the wetting time using two standard sol- utions, at five concentrations for each, and then using the sur- face active agent solution under test, also at five different con- centrations. After plotting the three “wetting time/concentration” curves, determination of the we
4、tting power of the surface active agent under test by comparison of the position of its curve with the two standard curves. IS0 3819: 1985, Laboratory glassware - Beakers. 5 Reagents and products 3 Definition For the purposes of this International Standard, the following definition applies. 5.1 Dist
5、illed water, or water of equivalent purity, complying with the specifications of IS0 2456. Other grades of water may be used provided details are noted in the test report. 1 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Defense Supply Ctr/99
6、60866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8022 : 1990 (El 6.2 Sodium di-n-hexylsulfosuccinate, of recognized analytical grade. 6.4 Stopwatch, accurate to 0,l s. Dimensions in millimetres 5.3 Sodium di-n-heptylsulfosucci
7、nate, of recognized analytical grade. 6.4 Raw cotton control cloth, of known nature and characteristics, conditioned in the standard temperate at- mosphere specified in IS0 139, i.e. a relative humidity of 65 % and a temperature of 20 OC. (Various types of commercially available control cloths are d
8、escribed in annex A.) 6 Apparatus Ordinary laboratory apparatus and, in particular: 6.1 Beaker, low form, of capacity 1 000 ml, complying with the specifications of IS0 3819. 6.2 Cloth-immersion gripper, made of stainless-steel wire of about 2 mm diameter and whose dimensions are given in figure 1 (
9、see also the photo, figure 2, which shows an example of a gripper constructed in accordance with figure 1, with three support arms projecting at right angles from the gripper body). These arms may be mounted on a sliding collar as shown in figure 1. It is important that the design of the gripper is
10、such that, when a raw cotton disc held in the gripper is immersed in 700 ml of test solution in the 1 000 ml beaker (6.11, the cotton disc is held about 40 mm below the surface of the solution. It is also important that the gripper tips only open about 6 mm so that the cotton disc remains nearly ver
11、tical in the solution. o tl! 6 6.3 Punch, of diameter 30 mm, carefully degreased using a volatile solvent (for example dichloromethane). Figure 1 - Cloth-immmersion gripper 2 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Defense Supply Ctr/9
12、960866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8022 : 1990 (El Figure 2 - Photo showing example of gripper constructed in accordance with the requirements specified in 6.2 Figure 3 - Illustration of procedure 3 Copyright In
13、ternational Organization for Standardization Provided by IHS under license with ISO Licensee=Defense Supply Ctr/9960866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8022 : 1990 (El 1 = 2 E C 2 E d E u O,l Sodium di-n-he lsulfosu
14、ccinate Wetting time (s) Figure 4 - “Wetting time/concentration” curves for surface active agents A, B and C, with standard curves for comparison 4 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Defense Supply Ctr/9960866100 Not for Resale, 0
15、4/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8022 : 1990 (El 7 Sampling The surface active agent laboratory sample shall be prepared and stored in accordance with IS0 607. 8 Procedure 8.1 Test portion Weigh, to the nearest 0,l g, 5 g of the laborat
16、ory sample into a 100 ml beaker. 8.2 Preparation of the surface active agent solution Dissolve the test portion (see 8.1) in water, if necessary after first making a paste of the surface active agent with water warmed to 40 “C, then diluting with water at about 20 “C. Transfer quantitatively to a 1
17、000 ml volumetric flask, make up to the mark with water and mix. Take 200 ml of the solution thus obtained, transfer to a 1 000 ml volumetric flask, make up to the mark with water and mix. If the Krafft temperature of the surface active agent is higher than 40 OC, make the paste and carry out the di
18、ssolution at a temperature at least equal to the Krafft temperature. Prepare the solution not less than 15 min, but not more than 2 h, before the measurement. Keep the solution at 20 - C + 2 OC until the beginning of the test. Conditions other than those given above (concerning the hard- ness or pH
19、of the water, temperature, possible assistants) may be chosen provided that they are noted in the test report. 8.3 Preparation of the discs of cotton control cloth Using the punch (6.31, cut out discs of 30 mm diameter from the raw cotton cloth (5.4). It is very important to avoid touching the cloth
20、 with the fingers as the presence of fatty materials or perspiration on the surface of the cloth may affect the results. 8.4 Cleaning the apparatus The success of the tests depends, to a certain extent, on the cleanness of the apparatus. Before the test, and if possible overnight, leave a chromic/ s
21、ulfuric acid mixtureI), prepared by gently stirring sulfuric acid fez0 I,84 g/ml) into an equal volume of a saturated solution of potassium dichromate, to stand in the beaker (6.1). Then rinse the beaker with water (5.1) until all traces of acid have disap- peared, finally rinsing with a small quant
22、ity of the solution under test. Clean the gripper (6.2) for 30 min in an azeotropic mixture of ethanol and trichloroethylene, dry, then rinse with a small quantity of the solution under test. For a particular surface active agent under test, the apparatus is only rinsed between measurements with the
23、 solution at a new concentration. 8.5 Filling the measurement beaker Using a measuring cylinder, introduce 700 ml of the test sol- ution prepared in 8.2 into the measurement beaker (6.1). During these operations, in order to avoid the formation of undesirable foam, it is recommended that the test so
24、lution be allowed to flow down the internal walls of the vessels. If necessary, remove any foam formed on the surface of the sol- ution in the measurement beaker with a filter paper. 8.6 Determination (see figure 3) Measure, to the nearest 1 C, the temperature of the solution. Clamp a raw cotton dis
25、c (8.3) in the gripper (6.2). Immerse the disc in the solution, starting the stopwatch (6.4) at the moment when the lower part of the disc touches the solution. Rest the support arms on the rim of the beaker and allow the gripper to open. Stop the stopwatch when the disc begins to sink of its own ac
26、cord. In the case of solutions at high temperatures, it is important to wait at least 15 min after stabilization of the temperature before carrying out the measurement. If the wetting time for the first test solution (concentration 1 g/l) is not about 300 s, adjust the mass of the test portion cor-
27、respondingly and repeat the procedure until the test solution concentration has been found which gives a wetting time of about 300 s. When this test solution concentration has been found, repeat the measurement nine times on this solution, but taking a fresh cotton disc for each measurement. Calcula
28、te the arithmetic mean of the IO measurements and record this as the wetting time for that particular test solution concentration. Prepare, in the same way as for the first test solution, four further solutions of increasing concentration and determine the wetting time for each, using the procedure
29、specified above. En- sure, by carrying out preliminary measurements if necessary, that the solution of highest concentration has a wetting time of 5 s k 1 s. If this wetting time cannot be attained, use a saturated solution as the solution of highest concentration. I) Other cleaning solutions may be
30、 used provided that they are noted in the test report. 5 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Defense Supply Ctr/9960866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,
31、- IS0 8022 : 1990 (E) 8.7 Calibration of the cloth Determine, using the same procedure and at the same temperature as for the surface active agent under test, the wet- ting times for five solutions of each of the two di-n-alkyl- sulfosuccinate standards (5.2 and 5.3). The first (least concentrated)
32、solution of sodium di-n-heptyl- sulfosuccinate (5.3) shall be 0,2 g/l. The first (least concen- trated) solution of sodium di-n-hexylsulfosuccinate (5.2) shall be I,3 g/l. The calibration of the cloth is necessary only if a new batch of cotton control cloth is used, or if it is desired to compare th
33、e results obtained from two different control cloths. 9 Expression of results On log-log paper, plot wetting time against concentration for the surface active agent under test and for the two di-n- alkylsulfosuccinate standards (see figure 4 for an example). A comparison of the positions of the thre
34、e curves gives a reasonable estimate of the wetting power of the surface active agent under test. 10 Test report The test report shall contain the following information: a) all details necessary for complete identification of the sample; b) the nature and characteristics of the raw cotton cloth from
35、 which the discs were cut (see annex A); c) the method used (a reference to this International Standard); d) the nature of the water used and, if appropriate, the assistants used; e) the exact temperature of the determination; f) the curves representing the results; g) details of any operations not
36、specified in this Inter- national Standard or in the International Standards to which reference is made, and details of any operations regarded as optional, as well as details of any incidents which may have influenced the results. Copyright International Organization for Standardization Provided by
37、 IHS under license with ISO Licensee=Defense Supply Ctr/9960866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8022 : 1990 (E) Annex A (informative) Commercially available control cloths German cloth Unbleached cotton cloth - mass
38、 per unit area determined in accordance with IS0 3801: 494 g/m* - number of threads in warp determined in accordance with IS0 7211-2: 11 threads per centimetre - number of threads in weft determined in accordance with IS0 7211-2: 11 threads per centimetre - warp threads: 50 tex 2 330 x 4s 330; R 200
39、 tex - weft threads: 50 tex 2 330 x 4S 330; R 200 tex French cloth Unbleached cotton cloth pure superior America, without finish or charge - mass per unit area determined in accordance with IS0 3801: 300 g/m* - number of threads in warp determined in accordance with IS0 7211-2: 18 threads per centim
40、etre - number of threads in weft determined in accordance with IS0 7211-2: 13 threads per centimetre - warp threads: 42 tex 2 550 x 2S 500; R 84,5 tex - weft threads: 42 tex Z 550 x 2S 500; R 84,5 tex Annex B (informative) Bibliography IS0 3801 : 1977, Textiles - Woven fabrics - Determination of mas
41、s per unit length and mass per unit area. IS0 721 l-2 : 1984, Textiles - Woven fabrics - Construction - Methods of analysis - Part 2: Determination of number of threads per unit length. 7 Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Defense
42、 Supply Ctr/9960866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,- IS0 8022 : 1990 (E) UDC 621.185 : 620.1 : 532.696.1 Descriptors : sutfactants, tests, determination, wettability, immersion. Price based on 7 pages Copyright International Organization for Standardization Provided by IHS under license with ISO Licensee=Defense Supply Ctr/9960866100 Not for Resale, 04/24/2007 10:26:08 MDTNo reproduction or networking permitted without license from IHS -,-,-