《JIS-B-1575-1979-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-B-1575-1979-ENG.pdf（12页珍藏版）》请在三一文库上搜索。
1、- J I S B*1575 79 m 4933b08 0010735 O m UDC 62-725.2 7 - JIS JAPANESE I NDUSTRIAL STANDARD Grease Nipples JE B I 575 -1979 Translated and Published by Japanese Standards Asso Printed in Japan iati n Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees
2、/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- Translation without guarantee standard in Japanese is to be evidence i n the event of any doubt arising, the original Copyright Japanese Standards Association
3、Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- 1 i J I S B*l1575 79 4933608 0030737 4 UDC 62-725.2 JAPANESE INDUSTRIAL STANDARD J I S Gr3 Grease N
4、ipples B 1575-1979 1. Scope This Japanese Industrial Standard specifies grease nipples, hereinafter referred to as the “nipples“, to be used for general machines, automobiles, ships, etc, Remark: In this standard, the units and numerical values given in 1 are in accordance with the International Sys
5、tem of Units (SI), and are given for reference. Applicable Standards : J E 3 B 0202-Parallel Pipe Threads J E B 0203-Taper Pipe Threads JE B 0207-Metric Fine Screw Threads JE B 0211-Limits of Sizes and Tolerances for Metric Fine Screw Threads J E 3 B 0405-Permissible Machining Deviations in Dimensio
6、ns without Tolerance Indication JE B 9808-Grease Guns J E 3 G 4051-Carbon Steel for Machine Structural Use J E 3 G 4401-Carbon Tool Steels . JIS G 4804-Resulphurized Carbon Steels J E 3 H 3250-Copper and Copper Alloy Rods and Bars JE H 8610-Electroplated Coatings of Zinc on Iron and Steel Copyright
7、Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- JIS B*1575 77 W LI933608 0030738 b _- 2 B 1575-1979 Classes Material
8、 Surface hardening Treated with surface harden- ing (Symbol H ) Steel nipples Treated with no surface hardening Brass nipples - 2, Classes and Types Types (See Attached Figs.) Type A-M 6 F, Type A-MT 6 x 0.75, Type A-PT 1/8, Type A-PT 114, “Y& B and Type C Type A-MT 6 x 1, 3 Performance 3.1 Grease I
9、nflow When the grease is flowed into the nipple fixed to a chuck type nozzle (1) under the pressures of approx. 30 kgf/cm2 (3 MPa and then approx, 280 kgf/cm2 (28 MPa, the grease shall flow in condition and the steel ball shall turn without abnormality, Note (l) The chuck type nozzle is referred to
10、JE3 B 9808, . 3.2 Pressure Resistance When grease is injected into the threaded side of the nipple, under pressure of 35 kgf/cm2 (3.5 MPa, the nipple shall show no harmful leakage nor other abnormality. 3.3 impact Strength When a nipple which has been fixed to a testing apparatus, as shown in Fig. 1
11、, with its head screwed in horizontally is subjected to -an impact of 1,5 kg weight generally of 50 mm diameter cylinder made of SK 5 steel of JE3 G 4401) falling freely from a vertical height ( H ) given in Table 2, the nipple shall show no separation, crack and fissure. Copyright Japanese Standard
12、s Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S Ba1575 79 4933608 0010739 B 3 B 1576-1979 Fig. 1 1 i Table 2 Unit: mm T Y P Hei
13、ght (H) . 100 Types A-M 6 F, A-MT 6 x 1 and A-MT 6 x 0.75 Types A-PT 1/8 and A-PT 1/4 300 Types B and C I 100 i n this case, a proper guide shall be so provided that the smallest section of the nipple may position on the extended plane of the side face of the weight, and the nipple shall be so fixed
14、 that the bearing face of the hexagonal part may be in close contact with the testing apparatus. For the Types B and C, the impact strengths shall be referred to the nipple head. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wi
15、ng, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*1575 79 m 4933608 0010740 4 m I _ * 4 B 1575-1979 4. Hardness The steel nipples of which head has been surface hardened shall have depth of hardening of O. 1 mm or more wi
16、th surface of such hardness that the surface can scarcely be rasped with a file of 40 in hardness number on H,C scale, 5. Shape and Dimensions The shape and dimensions of the nipples shall conform to Attached Figures, 6 . Appearance The nipple shall be free from crack, harmful flaws, flashes and def
17、ects such as broken crest of the threaded portion. 7. Materials The materials of the nipple body and nipple head shall be in accordance with Table 3, as a rule. Table 3 Class I Ma ter ia1 S 15 C and S 20 C of JIS G 4051 SUM 22 o f JIS G 4804 Steel nipples Brass nipples C 3601 B to C 3604 B of JIS H
18、3250 8. Plating The steel nipples shall be subjected to zinc electroplating. It shall prove itself to be of Grade MFZn II or more, when tested in accordance with JIS H 8610. The threaded protioris are exempted from the above rule. . Specification for nickel plating, when required, onto the brass nip
19、ples shall be as agreed upon between the parties concerned in acceptance. . 9 . Inspection 9.1 Inspection on Grease Inflow The grease idow shall comply with the requirements o f 3 1 9.2 Inspection on Pressure Resistance The pressure resistance shall comply with the requirements of 3.2. Copyright Jap
20、anese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- 5 B 1575-1979 9.3 Inspection on Impact Strength The impact strength sha
21、ll comply with the requirements of 3.3. undiscerned after the application of the impact, the surrounding of the steel ball of the head shall be sealed tightly as shown in Fig. 2, and pneumatic pressure of 3 + 0.5 kgf/cm2 (0.3 c + 0.05 MPa shall be applied from the fitting thread side of the nipple,
22、However, in the case where the existence of abnormalities are visually When no leakage appears, the nipple shall be accepted. Fig. 2 Tightly sealed pressure - - - 9.4 Inspection on Hardness The hardness shall satisfy the requirements of 4. 9.5 Inspection on Shape and Dimensions The shape and dimensi
23、ons shall conform to the specifications of 5. 9.6 Inspection on Appearance The appearance shall comply with the re- quirements of 6. 9.7 Inspection on Materials The materials shall comply with the require- ments of 7, 9.8 Inspection on Plating The plating shall satisfy the requirements of 8. 10. Des
24、ignation The nipples shall be designated in the order of the number or title of this standard, type, material and surface hardening. When the title of this standard is used in the designation, the material Examples 1. JIS B 1575 Type A-M 6 i ? S 20 C H identification shall precede. 2, Steel grease n
25、ipple Type A-PT 1/8 3, JIS B 1575 Type A-MT 6 x 1 BsBM Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- J I
26、 S B*3575 79 E 4933606 O030742 B W 6 B 1575-1979 11. Marking The package of the nipples shall bear the following particulars on its outs ide : (1) (2) Quantity (3) Class and type (The product having been subjected to surface hardening shall bear the symbol H.) Name of manufacturer or its abbreviatio
27、n Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*1575 79 I I 4933608 0010743 T A-M 6 F 1 Caulked
28、part Attached Figure Type A-MT 6 x 1 Type A-MT 6 x 0.75 Type A-PT 1/8 Type A-PT 1/4 7 B 1675-1979 Unit: mm Shape and dimensions of head b-y 1 $5.6 4 Caulked part L max. B O Type A-M 6 F M6XO.75 13.5 dz O. 4 4 5.4 7-0.2 Type A-MT 6 X 1 M T 6 X 1 13.5 f O. 4 4 5.4 7-0.2 Type A-MT 6 x 0.75 MT6XO.75 13.
29、5 f O. 4 4 5.4 7-0.2 -I Designation of (d) screw threads 5 p e O - O O Type A-PT 1/8 PT1/s 20 f 0.4 8 9.5 10-0.2 Type A-FT 1/4 PTI4 25 *0.4 11 12.5 14 4 . 2 5 Type B TYP c 102.2 102 Remarks 1. The screw threads for Type A-M 6 F shall be as specified in J E B 0207, and the accuracy shall conform to 6
30、 g or Grade 2 specified in JE B 0211. The screw threads for Types A-PT 1/8 and A-PT 1 / 4 and the screw threads for bodies of the Types B and C shall be as specified in JE B 0203. The fitting screw threads of the nipple heads of Types B and C may be altered, when speoified by the purober, Dimensiona
31、l tolerance, unless otherwise speoified, shall be of Medium Grade specified in JI8 B 0406. The direction of the hexagonal parta of Types B and C is shown for example. . 2 . 3 . 4 . The taper screw threads for MT 6 x 1 and MT 6 x 0.76 shall conform b-Appendix. Copyright Japanese Standards Association
32、 Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S BX1575 79 4933b08 0030744 I 8 B 1575-1979 Appendix Taper Screw Threads MT 6 x 1 and MT 6 x 0
33、.75 Basic profile Taper screw threaded portion . Position of gauge diameter * I / ! . Caulkedpart p C L , pitch Height of thread Designation P h MT6X1 1 O. 613 II MT6XO.75 I 0.75 I 0.460 Radius of rounding r O . 144 O. 108 H=O. 8660 P h=O. 6134 P r=O. 1443 P Unit: mm Gauge diameter Pdtlon of gauge d
34、iameter Applioable thread From pipe end grade of length Tolerance Major Pitch Minor internal diameter diameter diameter . Basic d, d S U 6 d O 6H O 6H 6.000 5.350 4.773 1. o O 6.000 5.513 5.080 -1.0 or Grade 2 -1.0 or Grade2 Copyright Japanese Standards Association Provided by IHS under license with
35、 JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- 9. B 1575-1979 e Reference: The button head and pin type grease nipples shown below do not constitute a part of this standard, but ar
36、e given for reference Button head Pin type Unit: mm - L max. - 9.5 Designation of thread (dl H B Designation (d) of thread H I zi O 17-0.25 18 f O. 4 27 f 0.4 8 30 f 0.4 11 O 17-0. z 21 i : 0.4 11 - 12.5 - Remarks 1. The screw threads PT 1/8 ard PT 1/4 are as specified in JIS B 0203 and the threads
37、PF 1/8 and PF 1/4 in JIS B 0202. 2. Unless otherwise specified, dimensional tolerance shall be of Medium Grade specified in JE B 0405. 3. The product shall be designated in the order of the name of product, designation of thread (d) and material. Example: Button head PT 1/8 Brass Copyright Japanese
38、Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,- B 1575-1979 Edition 1 Japanese Text Established by Minister of International
39、Trade and Industry Date of Establishment: 1960-11-01 Date of Revision: 1979-01-01 Date of Public Notice in Official Gazette: 1979-01-29 nves tigated by: Japanese indus trial Standards Committee Divisional Council on Machine Element This English translation is published by: Japanese Standards Associa
40、tion 1-24, Akasaka 4, Minato-ku, Tokyo 107 Japan 0 JSA, 1980 Rinted in Tokyo by Hohbunsha Co.,Ud. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/12/2007 09:13:43 MDTNo reproduction or networking permitted without license from IHS -,-,-