《JIS-B-9218-1986-R2003-ENG.pdf》由会员分享，可在线阅读，更多相关《JIS-B-9218-1986-R2003-ENG.pdf（20页珍藏版）》请在三一文库上搜索。
1、J I S B*92L8 8b I 4933608 0024722 3 “JI$ o JAPANESE INDUSTRIAL STANDARD Standard Form of Specifications of Head- f eeding Type Com bines Translated and Published by Japanese Standards Association Printed in Japan UDC 631.351.36 11 s Copyright Japanese Standards Association Provided by IHS under lice
2、nse with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*21B Bb 4933608 0024923 5 M In the event of any doubt arising, the original Standard in Japanese is to be final author
3、ity. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S Ba9218 86 4933608 O024924 7 UDC 631.35/. 36 JAP
4、ANESE INDUSTRIAL STANDARD J I S Standard Form of Specifications of B 9218-1986 Head-feeding Type Combines 1. Scope This Japanese Industrial Standard specifies the standard form of specifications and its entry gist of head-feeding combines ( ) , hereinafter referred to as the llcombinesll. Note (l) I
5、t is also expressed by JIDATSUGATA combines, but in this standard it is called to be head-feeding dye combines. Remark: The units and numerical values given in in this Standard are based on the traditional units and are appended for informative reference. 2. Standard Form of Specifications a The sta
6、ndard form of specifications shall be as follows: (1) The standard form of specifications shall be in accordance with Attached Table 1 and Attached Table 2. (2) Attached Table 1 indicates the summary of elements and performances of combines, Attached Table 2 indicates uses, preparation and details f
7、or other technical purposes, and is used in combination with Attached Table 1. (3) Items may be selected corresponding to purposes, as required, structure, materials, test method, etc. of each part shall be appended and the drawings such as full view, layout drawing near the operator cab, etc., adde
8、d. (4) On the full view, outlines of outer profile of combine, layout of cab, and the like, and main dimensions shall be indicated. On the layout drawing near the operator cab, outlines and main relating dimensions of steering lever, each type pedal, each type lever, instruments, indicating apparatu
9、ses required for operation and travelling of combine shall be shown. (5) Applicable Standards: See page 9. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or net
10、working permitted without license from IHS -,-,- J I S B*92LB Bb 4933b08 0024925 9 = 2 B 9218-1986 3. Entry Gists of Specifications The entry gists of specifications shall be as follows: (1) Attached Table 1 The entry gist of Attached Table 1 shall be as follows : Name and Style Enter the manufactur
11、ers name mark and style symbol attached to the combine. Common Name The common name of the manufacturer shall be entered. Manufacturers Name The name of manufacturing company or name of manufacturing facotry of combine, and the like shall be entered. Division of Classes or large class special automo
12、bile according to the Road Vehicles The division of small class special automobile Act shall be entered. Main Dimensions the standard equipped condition of combine shall be entered, and dimensions at standard working, entered in parentheses. Overall Width The maximum width shall be entered and its p
13、osition, appended. The dimensions at the time of storage under Overaldl Width The maximum width shall be entered and its position, appended. Overall Height part shall be entered and its position, appended. The height from the ground up to the highest Minimum Ground Clearance part of machine body nea
14、r the machine body central line shall be entered its position, appended. Overall Mass the fuel is fully laden, the lubricating oil, working oil and cooling water are at specified amount, and specified portable tools and other accessories are equipped, shall be entered. The ground clearance of the lo
15、west The mass in the standard equipped condition when Endne Name and Style attached on the engine shall be entered. The manufacturers name mark and style symbol Type of Engine The cylinder layout, cooling system, number of gas cylinders, division of cycles, type of engine, and for others, as require
16、d, type of combustion chamber, valve arrangement and type of supercharger shall be entered. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or networking permitt
17、ed without license from IHS -,-,- J I S B*9218 86 4933608 O024926 O 3 B 9218-1986 (c) Overall Stroke Volume Ehe value calculated according to the following formula shall be entered: where v : overall stroke volume ( I ) D : inner diameter of cylinder (mm) L : stroke (mm) N : number of cylinders n :
18、3.1416 Further, for entry value shall be of three places of decimals by discarding up to four places of decimals. (d) Engine Output The number of revolutions and output designated by the manufacturer shall be entered. (e) Using Fuel Classification such as gasoline, gas oil, etc. shall be entered. (f
19、) Fuel-Tank Capacity The tank capacity shall be entered, and in the case of having auxiliary tank, it, appended. (g) Starting System The system such as cell motor type, recoil type, etc. shall be entered. (1.8) Travel Parts (a) Crawler The width of crawler, track gauge and average ground contact pre
20、ssure shall be entered. Further, for track gauge, the central distance of right and left crawlers shall be entered and for average ground contact pressure, the value of gravity acting on overall mass divided by the crawler ground contact area shall be entered. (b) Speed Change Style pressure type sh
21、all be entered, and, as required, speed change style, number of change stages, style of pump, class of working oil, etc., appended. The division of mechanical type and oil (c) Travel Speed speeds shall be entered by design value. The minimum value and maximum value of travel (d) Working Speed speed
22、shall be entered by design value. The minimum value and maximum value of working (1.9) Harvesting Parts (a) Harvesting Width The maximum harvesting width by action of divider shall be entered. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/11111
23、11001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S B*218 86 m 4933608 0024927 2 m 4 B 9218-1986 Number of Harvesting Streaks for harvesting of rice of planting streak interval of 28 to 33 cm shall be entered an
24、d for machine changeable the number of streaks, its pursuit, appended. The number of streaks guaranteed Number of Speed Change Stages The speed change stages of harvesting apparatus or the like, shall be entered. Width of Blade outer sides of harvesting blade shall be entered. The interval of tips o
25、f blade receiver at both Range of Harvesting Height in the range capable of guaranteeing the harvesting of vertical crops shall be entered and the division of oil pressure and manual working, appended. The lowest value and highest value (i. 10) Threshing Selecting Part (a) Style of Threshing mixing
26、up, axial flow type, etc. shall be entered. The division of upper mixing up ( 2 ) , lower Note ( 2 ) llKOKI1l of threshing part is also called to be “KOGI“, but in this Standard it is unified with “KOKI“. (b) Mixing-up Shell Diameterx width and number of revolutions shall be entered. Further, for di
27、ameter, mixing-up tooth is not included. For width, the mixing-up shell width shall be entered, and in the case where the numbers of revolutions for rice and for barley are different, the effect, appended. Treatment Shell shell. (c) It shall be entered same as that of mixing-up (d) Selecting Style T
28、he division of pressure wind, suction oscillation, etc. shall be entered. (1.11) Cereal-Power Taking-Out Part (a) Style The division of grain tank type, hopper bag filling type, discharge outlet bag filling type, etc. shall be entered and for bag filling type, the number of discharge outlets, append
29、ed. Further, rice-hulling bag used for bag filling type shall be entered. Furthermore, in the case of according to Appendix, the effect shall be appended. (b) Capacity The capacities of tank, and hopper shall be entered by number of bags and volume or mass. (1.12) Waste Straw Treatment Part Division
30、 of dropper cutter, binder, etc. shall be marked, and division of standard equipment and option, appended. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or net
31、working permitted without license from IHS -,-,- J I S B*92L8 8b I 4933b08 0024928 4 I 5 B 9218-1986 (1.13) Working Efficiency lated from the following formula, and the range, entered. The treatment time per 10 a shall be calcu- where H : treatment time per 10 a (min) w: blade width (m) v : the lowe
32、st speed capable of harvesting, the highest speed capable of harvesting (m/s) Further, the entering value shall be of integer and the decimal number be counted to unit of integer. (1.14) Automatic Control Apparatus In the case where the automatic control apparatus is provided, its name shall be ente
33、red. (1.15) Safety Apparatus described, it shall be entered. When there is an apparatus to be specially (1.16) Alarm Apparatus described, it shall be entered. When there is an apparatus to be specially (1.17) Others (a) Style Recognition Number or New Style Report Number The style recognition number
34、 of small type special automobile or new style report number of large type special automobile in accordance with the Road Vehicles Act shall be entered. (ia) Style Inspection Compliance Number In the case where there is a test result of style inspection to be erected by country or by other public in
35、stitute such as safety judgement compliance number and test result of other public institute, its number or the like shall be entered. (2) Attached Table 2 follows : The entry gist for Attached Table 2 shall be as e Travel Performance Range of Travelling Speeds travelling speed stage shall be entere
36、d by design value. The travelling speed at each Range of Working Speed shall be entered by design value. The working speed at each speed stage Minimum Slewing Radius machine-body outermost side slewing radius shall be entered by actually measured value. Concerning left slewing and right slewing, Cop
37、yright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or networking permitted without license from IHS -,-,- J I S BX92LB 86 4933608 0024929 b = 6 B 9218-1986 (2.2) Engin
38、e (2.2.1) Fuel System (a) Speed Governor Division of centrifugal type, pneumatic type, all speed type, etc. shall be entered. Further, as required, style attached by the manufacturer shall be appended. (b) Carburetor, Injection Pump and Nozzle The type or style attached by the manufacturer shall be
39、entered. (2.2.2) Lubricating System (a) Lubricating Style Division of pressure feed type, splash type, etc. shall be entered. (b) Lubricating Oil Capacity The total capacity shall be entered. (c) Filtration Style Division of full-flow type, bypass type, etc. shall be entered. (2.2.3) Cooling System
40、(a) Cooling Style The style of cooling shall be entered. (b) Cooling-Water Capacity The total capacity including the capacities in water jacket and radiator shall be entered. the case where auxiliary tank, heating apparatus, etc. exist, the effect shall be appended. In (2.2.4) Air Cleaner Style Divi
41、sion of filter paper type, oil-tank type, centrifugal type, etc. shall be entered. (2.2.5) Accumulator Number of units, voltage, and capacity shall be entered. Oil- Hv dr aulic Ax, D arat u s Pump Style Division of gear pump, vane pump, etc. shall be entered, and, as required, using site, oil-hydrau
42、lic diagram, etc. , appended. Working Oil The name, symbol, etc. shall be entered and the cooling system, appended. Working-Oil Capacity The total capacity shall be entered. Clutch Travel Clutch entered. The style and the like of the clutch shall be Steering Clutch entered. The style and the like of
43、 the clutch shall be e o Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS Employees/1111111001, User=Wing, Bernie Not for Resale, 03/16/2007 00:16:48 MDTNo reproduction or networking permitted without license from IHS -,-,- JIS B*9218 Ab I 4933608 0024930 2
44、 I 7 B 9218-1986 (c) Harvesting Clutch entered. The style and the like of the clutch shall be (d) Threshing Clutch entered. The style and the like of the clutch shall be (e) Straw Treatment Clutch shall be entered. The style and the like of the clutch (2.5) Change Gear (2.5.1) Machine Type (a) Style
45、 The gear style, speed-change style and operating style shall be entered and the lubricating system, appended. (b) Number of Stages entered. The number of speed-change stages shall be (2.5.2) Oil-Hydraulic Type (a) Pump Style Division of gear pump, vane pump, etc. shall be entered, and, as required,
46、 the using site, oil pressure diagram, etc. , appended. (b) Working Oil The name, symbol, etc. shall be entered and the cooling system, appended. (6) Working Oil Capacity The total capacity shall be entered. Braking Device Travelling Brake Division of pedal type, manual type, etc., and the division
47、of wet type and dry type shall be entered. Steering Brake Division of pedal type, manual type, etc. and the division of wet type and dry type shall be entered. Parking Brake Division of pedal type, manual type, etc. and the division of wet type, and dry type shall be entered. Operating Apparatus Sea
48、t Division of fixed type, adjusting type, etc. shall be entered. Lever and Pedals The names of lever and pedals used for working operation shall be entered. Instruments The name shall be entered. Further, the alarming apparatus and the like substitutive to the instrument shall be also entered. Illuminating Device The name shall be entered. Others The names of other devices such as alarm device, rear reflection mirror, etc. required for operation. Copyright Japanese Standards Association Provided by IHS under license with JSALicensee=IHS E